Flashcards in Flows Deck (37):
What are the tasks associated with the Safety Check?
HYDRAULIC PUMP 3A
FFOD CREW OXYGEN MASK
FFOD OBSERVER OXYGEN MASK
What are the CP tasks on the originating flow?
What are the CP pre-start Tasks?
What aural warnings do you hear when you complete the cargo fire test?
What messages do you see when completing the cargo fire test 1? Test 2?
1: SMOKE CARGO warning message CARGO SQUIB 1 advisory message
2: SMOKE CARGO warning msg CARGO SQUIB 2 advisory msg
Which lights are illuminated on the panel when completing cargo test 1? Test 2?
1: NORMAL and STANDBY CARGO SMOKE PUSH
NORMAL BOTTLE ARMED PUSH TO DISCH
2: NORMAL and STANDBY CARGO SMOKE PUSH
STANDBY BOTTLE ARMED PUSH TO DISC
What aural warnings are heard when completing the bleed detection test?
“BLEED AIR DUCT”
What messages appear when completing the bleed detection test?
L & R 10th and L & R 14th DUCT, & ANTI ICE DUCT msgs
What lights illuminate when completing the Bleed Air Duct test?
L & R 10th and L & R 14th DUCT FAIL warning lights
DUCT FAIL warning light
What indications are shown when completing the ICE DETECTOR test?
ICE light illuminated and ICE caution message
ICE advisory message
How long do you hold the button for the CVR test?
What aural warnings are heard in the MLG overheat test?
“GEAR BAY OVERHEAT”
What warning msg is associated with MLG overheat test?
MLG BAY OVHT msg
What indications are present when completing the MLG OVHT TEST WARN FAIL?
Single chime and master caution
MLG OVERHEAT FAIL caution msg
What emergency equipment needs to be checked in the flight deck?
3 life vests under seats
1 crash axe behind FO
1 escape rope by hatch
2 LED flashlights one on each side
1 PBE behind the CA
1 halon Fire Extinguisher behind FO
What conditions must be met to complete the FFOD Stall Test?
HYD 3A on
Stab Trim 6.0
STALL PTCT ON
Stall : press
After the FFOD Stall Test what needs to be turned off?
What test is completed with the EFIS section of the Originating flow?
What indicates a successful CVR test?
Needle goes in the green arc
Green light illuminates
What does the CA say when responding to the O2 part of the Originating checklist?
Checked and actual O2 reading
When should the anti-skid switch be moved to armed?
During the originating check flow, when reaching the upper pedestal
When are the thrust reversers armed?
During the originating check flow when reaching the thrust lever quadrant
When is the TCAS tested?
During the originating check flow, when reaching the lower pedestal
What modes must be selected to complete the FFOD Radar Test?
Tilt + 6 degrees
Auto tilt: off
Radar mode selector: off
What are the steps of the STAB TRIM TEST?
1. Select : STAB TRIM, CH 1, MACH TRIM
2. Look for STAB TRIM CH2 INOP msg
3. Operate both stab trims in both directions
4. Disconnect FOs stab trim
5. See STAB TRIM and MACH TRIM caution msgs
6. STAB TRIM is inop
7. Select STAB TRIM, CH2 and MACH TRIM
8. See STAB TRIM CH 1 INOP msg
9. Move both switches up/down to clicker activation
10. Press CAs stab trim disconnect
11.see STAB TRIM and MACH TRIM caution msg
12. STAB TRIM is inop
What is the last step for the FFOD Stab Trim Test?
Select STAB TRIM CH 1 & 2 and MACH TRIM
Note: caution and status msgs disappear
What is the normal position for the compasses?
What needs to be accomplished with the Trim on the originating check?
move the Aileron and rudder trim, and return to center
What is the recommended time to start the APU?
10 min prior to departure
What do you need to check when turning on the BATT MASTER?
That the charger is greater than 22 volts for the MAIN BATT and the APU BATT
What aural warnings are associated with the FFDO Firex Warning Test?
“JET PIPE OVERHEAT”
Which lights are illuminated during the FIREX WARN TEST?
L / R ENG FIRE PUSH
APU FIRE PUSH
L / R BOTTLE 1 / 2 ARMED PUSH TO DISCH
APU BOTTLE ARMED PUSH TO DISCH
What ED1 msgs are displayed during the FFDO Firex Monitor Test?
L/R JETPIPE OVERHEAT
L/R ENG FIRE
During the FFDO Firex Monitor Test Fail what ED1 indications are shown?
APU FIRE FAIL
R / L JET OVHT FAIL
R / L FIRE FAIL
When testing the ENG BTL 1 & 2 and APU BTL on the FFDO Firex monitor test, what indications are you looking for?
ED2 advisory msgs:
L/R ENG SQUIB 1/2
APU SQUIB 1/2
Why must HYD 3A be energized during the safety check?
To ensure operation of nose gear doors for walk around inspection
To ensure pressure for parking brake operation