RME 2-B

Question 1

For 809 A circuits, the minimum insulation resistance shall be

Answer 1

5000 ohms

Question 2

Receptacles located within the room bathrooms, playroom, activity room, and patient care areas if pediatric wards shall be listed as _______

Answer 2

Tamper resistant

Question 3

Surface metal raceways and their fittings shall not be so designed that the sections can be _______.

Answer 3

Electrically coupled together
Mechanically coupled together
Installed without subjecting the wire to abrasion

Question 4

No ______ shall be located in cellulose nitrate film storage vault.

Answer 4

Receptacles
Heaters
Portable electric equipment

Question 5

Listed baseboard heaters include instructions that may not permit their installation _____ dwelling unit receptacles outlets

Answer 5

Below

Question 6

Branch circuit that supplies a number of outlets for lighting and appliances

Answer 6

General purpose branch circuit

Question 7

This type of cable is a fabricated assemble of insulated conductors enclosed in a flexible metal sheath.

Answer 7

Armored cable

Question 8

Flexible appliances rated are not over ____ VA or 1/8 hp, the branch circuit overcurrent device shall be permitted to serve as the disconnecting means.

Answer 8

300

Question 9

Type MI cable shall be permitted ______

Answer 9

As feeders and branch circuits
For wet and dry locations
For concealed or exposed

Question 10

Expansion fittings for RNC shall be provided to compensate for thermal expansion and contraction where length change , expected to be _____ or greater

Answer 10

6 mm

Question 11

A device that, by insertion in a receptacle, establishes a connection between the conductors of the attached flexible cord and the conductors connected permanently to the receptacle is called a(n) _______.

Answer 11

Attachment plug
Plug cap
Plug

Question 12

Multioutlet assembly may be used _____.

Answer 12

In dry locations

Question 13

Multispeed motors shall be marked with the Code letter designating the locked-rotor ______ per horsepower for the highest speed at which the motor can be started

Answer 13

KVA

Question 14

The power conductors in non-metallic sheathed cable (type NMS cable) are manufactured in sizes _____ copper.

Answer 14

2.0 mm2 to 30 mm2

Question 15

_______ is an electric power production system that is operating in parallel with and capable of delivering energy to an electric primary source supply system

Answer 15

Interactive system

Question 16

At least how many receptacle outlet(s) shall be installed in the bathroom?

Answer 16

One

Question 17

Bends in FMC ______ between pull points

Answer 17

Shall not exceed more than 360 degrees

Question 18

Operation of equipments in excess of normal, full load rating or of a conductor in excess of rated ampacity.

Answer 18

Overload

Question 19

A ______ is a circuit operating at 600 volts nominal, or less, between phases that connects two power sources or power supply points, such as secondaries of two transformers

Answer 19

Secondary tie

Question 20

If there are no overcurrent protective device rated 30 A or less with neutral connection, this panelboard is classified as a _______

Answer 20

Power panelboard

Question 21

The exposed surface of space heaters used to prevent condensation of moisture during shutdown periods shall not exceed ______ of the ignition temperature in degrees Celsius of the gas or vapor involved when operated at rated voltage.

Answer 21

80%

Question 22

Receptacles and attachment plugs shall be permitted to be of a lower ampere rating than the branch circuit but bit less than ____ percent of the luminaire (fixture) load current

Answer 22

125

Question 23

Liquid tight flexible nonmetallic conduit shall NOT be used where the voltage of the contained conductors is in excess of ______.

Answer 23

600 V

Question 24

When computing the service load, more than three fixed appliances are computed with a demand factor of ______ of the nameplate rating

Answer 24

75%

Question 25

A box of blank cover which is inserted in one or more runs of raceway to facilitate pulling of the conductor

Answer 25

Junction box

Question 26

Busways shall be permitted to be installed behind panels if means is access are provided and if the conditions below are met. One of them is NOT valid. Which one is this?

Answer 26

The busway is open and of ventilator type

Question 27

Similar ____ conductor length limitations applied at apartment buildings and commercial buildings will help to reduce voltages that may be developed between the building power and communications system during lighting events.

Answer 27

Grounding

Question 28

If the project extensive and requires more time for checking and for computations of fees, the issuance of electrical permit need not be issued immediately. However, the delay shall not be longer than how may working days?

Answer 28

5

Question 29

When computing the service load with the standard method, a 29 kW electric space heating unit is computed at _____ percent

Answer 29

100

Question 30

Heating panels or heating panel sets in poured concrete or masonry shall not exceed _______ watts/m2 of heated area

Answer 30

355

Question 31

Metal faceplates for park trailers shall be of ferrous metal not less than ____ in thickness or of non-ferrous metal not less than _____ in thickness

Answer 31

0.75 mm; 1.0 mm

Question 32

Thermal insulation shall not be installed within _____ of the recesses fixture enclosure

Answer 32

38 mm

Question 33

Each transformer shall be provided with a nameplate giving the name if the manufacturer, rated kVA, frequency, primary and secondary voltage, and impedance of transformers ____ kVA and larger.

Answer 33

25

Question 34

Auxiliary gutters shall not contain more than ____ current carrying conductors at any cross section.

Answer 34

30

Question 35

Bare bulbs installed backstage that shall come into contact with combustible material shall be guarded and provided with at least _______ mm of air space

Answer 35

50

Question 36

A bushing or adapter shall be provided to ____ the wire from abrasion unless the box, fitting or enclosure design provides equivalent protection

Answer 36

Protect

Question 37

The location of the disconnecting means for an elevator shall be ______ to qualified persons.

Answer 37

Readily accessible

Question 38

Conductors used in lighting protection system shall have no bend forming an included angle less than ______

Answer 38

90 degrees

Question 39

The long time rating for x-ray equipment is based on an operating time of _____ minutes or longer.

Answer 39

Five

Question 40

Rod electrodes of steal or iron shall be at least ____ in diameter

Answer 40

16mm

Question 41

A branch circuit that supplies a number of outlets for lighting and appliances

Answer 41

General purpose branch curcuit

Question 42

It is the intent of PEC that factory-installed internal winding or the construction of equipment need not to be inspected at the time of installation of the equipment except _______

Answer 42

To detect alterations

Question 43

Where the secondary tie system is grounded, each transformer secondary supplying the tie system shall be _____ in accordance with the requirements for the separately derived system.

Answer 43

Grounded

Question 44

Any switch or device normally used to start and stop a motor by making and breaking the motor circuit current

Answer 44

Controller

Question 45

At least one receptacle outlet shall be installed directly above a show window for each ______ linear meter length or a major fraction thereof.

Answer 45

Three

Question 46

Flat cable assemblies shall have conductors of _____ special stranded copper wires

Answer 46

5.5mm2

Question 47

To cut rigid steel conduits, an electrician should

Answer 47

Use a hack saw and ream the ends

Question 48

The minimum size of an amateur station outdoor antenna conductors, where the span is less than 45 meters, shall be at least _____.

Answer 48

2.0 mm2

Question 49

For an ambient temperature of 30 degree Celsius. A THW insulated copper conductor with a cross sectional area of 3.5mm2 and buried underground has the following ampacity. Which one is correct?

Answer 49

30 A

Question 50

At least ____ of free conductors shall be left at each outlet, junction, and switch point for splice or the connection of fixtures or devices

Answer 50

150 mm