SPV2020 Flashcards

1
Q

You see a flashing amber OPEN light next to the cockpit door switch (with the associated aural alarm). What does this mean?

A

Someone in the cabin has started an emergency access procedure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

With the EMER EXIT LT switch in the ARM position, what causes the emergency lighting system to illuminate?

A
  • Exit Signs, overhead emergency, and floor proximity lights illuminate with loss of normal electric power
  • Exit signs only with excessive cabin altitude
  • The exit signs will illuminate with landing gear extension if the NO SMOKING switch is in AUTO
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

With the STROBE switch in AUTO, when do the strobe lights operate?

A

WoW

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

With the LAND switches selected OFF, what is the status of the landing lights?

A

Extended but off

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Which lights illuminate with the EMER EXIT LT selected ON?

A

Overhead emergency, EXIT signs, floor proximity emergency escape path marking system are illuminated. Note, internal batteries (EPSUs) are not charged in this position and may only last 10 minutes in use.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What happens to the nose wheel response to tiller input as ground speed increases?

A

Nose wheel deflection response to tiller input is reduced as ground speed increases.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What does a fault light in the TERR pb mean?

A
  1. Terrain detection fault failure

2. Basic modes 1 - 5 still operational

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What will occur if the TERR PB is selected OFF?

A

Inhibits the database terrain detection function and keeps the basic GPWS modes 1 - 5 operative

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What does the GPWS SYS fault light indicate?

A

Basic GPWS mode 1 to 5 malfunction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is inhibited when the G/S MODE pb is selected off?

A

Mode 5, glideslope mode (“Glide Slope” aural) is inhibited

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What will occur if you selected the FLAP MODE push button off?

A

Flap mode 4 “TOO LOW, FLAPS” is inhibited to avoid nuisance warnings when landing with a reduced flap setting

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What occurs when the LDG FLAP 3 pb is selected ON?

A

Flap mode 4 “TOO LOW, FLAPs” is inhibited when FLAPS CONF 3 is selected. In this case, the ECAM LDG MEMO displays “Flaps….3” instead of “Flaps…..full”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Do we receive an ECAM notification when the smoke light illuminates and aural alert annunciates?

A

No, system is aftermarket and has no suppression or ECAM alert

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What does the RACK POWER smoke light and associated aural alert indicate?

A

SMOKE detected in the Aft Avionics Rack

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

If the SMOKE light in the RACK POWER illuminates and the associated aural alert is present, would you expect to see an associated ECAM?

A

No, it isn’t connected to the FWCs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

If an emergency access is initiated, how much time do you have to select “LOCK” in order to prevent unauthorized access to the flight deck?

A
  • Select the LOCK position within 30 seconds of the start of the emergency access procedures to deny entry
  • The cockpit door is locked, and emergency access is denied for 5 minutes
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Which cockpit lighting is available on battery power only?

A

The FO dome light is available with battery power

Capt flood lights work as well

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

With the EMER EXIT LT selector to ARM, when will the overhead emergency lights illuminate?

A

Loss of normal electric power

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

With the EMER EXIT LT selector to ARM, when will the EXIT SIGNS illuminate?

A
  • Loss of normal electric power
  • Excessive cabin altitude
  • With NO SMOKING sign in AUTO, EXIT signs also come on with the L/G down
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

With the EVAC switch in the CAPT position and an alert activated from the CABIN, what indications would be present in the cockpit?

A
  • The cockpit horn sounds for 3 seconds
  • CAPT sw: If activated from the cabin, the signal will only be apparent in the flight deck and will only sound in the flight deck for 3 seconds
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

The lights in the EMER switch flash and you hear 3 long buzzers sound in the Flight Deck. What does this indicate?

A

An emergency call has been made from the cabin to the flight deck

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Which button should be used to communicate with the cabin in an emergency?

A

EMER CALL button

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

What happens when you push the MECH pb?

A
  • COCKPIT CALL illuminates in blue on the external power panel and a horn sounds in the Nose L/G bay
  • Horn will sound as long as button is held
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

When are the CVR and FDR energized with RCRD GND CTL PB in AUTO (extinguished)?

A

AUTO: (extinguished) The CVR and FDR are energeized when

  • On the ground, 5 minutes after electrical power to the aircraft
  • On the ground, After engine start
  • Continuously in flight (whether engines are running or not)
  • On the ground, it is stopped automatically 5 minutes after the last engine shutdown
25
Q

What does the flashing amber CALL light indicate?

A

An incoming call detected by the SATCOM system

26
Q

What does the flashing blue ATC MSG light indicate?

A

ATC message received by CPDLC

27
Q

What is the primary difference on the engine warning display (EWD) as associated with engine monitoring on the NEO Pratt & Whitney engine?

A

On the Neo EWD, N1 replaces EPR as the primary engine parameter

28
Q

Due to improved stall margins on the PW1000G, logic for the automatic selection of Continuous Ignition is changed. Unlike CEO engines, the following do not trigger (or require) continuous ignition:

A
  • Engine A/ICE
  • TOGA or FLX thrust
  • Approach IDLE (flaps > 0)
29
Q

T/F - With the use of DUAL COOLING it is acceptable to start both PW1100G engines simultaneously.

A

False

30
Q

Airborne Traffic Situational Awareness (ATSAW) utilizes which technology in order to provide enhanced traffic awareness?

A

ADS-B IN/OUT

31
Q

Turbulence detection has been extended to ___ miles and is indicated in ____ on the ND with the enhanced “Hazard V2” weather radar.

A

60, magenta

32
Q

The soft-go-around function automatically adapts the thrust to maintain approximately what rate of climb?

A

2000 feet per minute

33
Q

To initiate the Soft Go Around Function, the pilot should move the Thrust Levers to:

A

TOGA initially then back to the FLX/MCT detent

34
Q

What is the position of the Pack Flow Control valves when the APU BLEED is ON?

A

High flow is provided if the APU is supplying bleed air (and in single pack operation regardless of selector position)

35
Q

What happens to the ENG BLEED valves when the APU BLEED valve opens?

A

Engine Bleed valves close

36
Q

Regardless of switch position, what Pack Flow is provided during single pack operations

A

HIGH

37
Q

What is indicated by a FAULT light in the HOT AIR pushbutton?

A

Duct overhead

38
Q

If the APU bleed valve is open and the X BLEED selector is in AUTO, what is the position of the X BLEED valve?

A

Open

39
Q

With the LDG ELEV selector in Auto, how is the LDG ELEV set?

A

FMGC database information

40
Q

What does the fault light in the cabin pressure MODE SEL switch indicate?

A

BOTH CAB PR systems have failed

41
Q

What happens to the ventilation system when either the BLOWER or EXTRACT p/b are selected to OVRD?

A

Air is added to the ventilation air from the Air Conditioning system

42
Q

What happens when the ditching pushbutton is selected on ON?

A

Sends a close signal to the inlets and valves below the water line

43
Q

With both ENG’s running, APU supplying bleed are, and the X BLEED switch in AUTO, what is the position of the X BLEED valve?

A
  • X BLEED valve is open

- ENG 1 (2) valves closed

44
Q

On takeoff, what speed does SRS command with both engines operating?

A

SRS gives pitch guidance to maintain airspeed at V2 + 10

45
Q

On takeoff, what speed does SRS command if an engine failure is detected?

A

SRS gives pitch guidance to maintain the greater of V2 or current speed, limited to V2 + 15

46
Q

When does the airplane exit SRS mode?

A

Automatically at the Acceleration Altitude or when another Vertical Mode is engaged

47
Q

With V/S active, what would happen if you selected a higher speed?

A

Thrust will increase (up to CLB, if needed) until the selected speed is attained. Then the thrust will reduce to maintain selected speed.

48
Q

Based on the PFD shown, what thrust is being commanded? (v/s descent going faster than selected speed)

A

Thrust at idle since speed selected is below indicated at descent

49
Q

During a normal takeoff, when will the A/THR become engaged?

A

A/THR becomes engaged (with A/THR on FMA) after the thrust lever is moved to the CLB detent

50
Q

In a managed climb, what FMA changes will occur if you pull HDG?

A

NAV mode will change to HDG, CLB mode will change to OP CLB

51
Q

In a managed descent, what FMA changes will occur if you pull HDG?

A

NAV mode will change to HDG, DES mode will change to V/S, THR mode will change to SPEED

52
Q

During an ILS Approach, at approximately what altitude will the LOC/GS indication change to LAND on the FMA an what does LAND mean?

A
  • Below 400’ RA
  • LAND indicates that the LOC and GS modes are locked. No action on the FCU will disengage the LAND Mode. FLARE and ROLLOUT Modes will successively engage
53
Q

During an autoland, when do you expect the FMA FLARE indication to appear?

A

40’ RA

54
Q

During an autoland, with the FMA ‘flare’ indication displayed, what actions are occurring within the autopilot and autothrust?

A
  • Autopilot aligns yaw axis with runway centerline and flares in pitch
  • Autothrust reduces thrust to idle if engaged
55
Q

Durn an autoland, what does ‘roll out’ indicate?

A

The autopilot is guiding the aircraft along the runway centerline and the yaw bar is displayed on the PFD

56
Q

What are the three ways you can disconnect the Autothrust?

A
  • Press either the autothrust instinctive disconnect pushbutton
  • Mode both thrust levers to idle
  • Push A/THR pb on the FCU (will cause thrust lock)
57
Q

In level flight with the with the thrust levers in the CL detent, what will happen to the thrust if you press the instinctive disconnect pb?

A

Thrust will go to CL (matching current position)

58
Q

What does THR LK mean?

A
  • Means: Thrust is fixed at the current setting. (Could result from a fault OR pressing the FCU/A/THR button)
  • To fix: move the thrust levers
59
Q

How would you get out of THR LK?

A

Move the thrust levers