120202a GTAW Process (Q&A) Flashcards
Define the term GTAW.
- Gas tungsten arc welding (GTAW), often referred to by its non-preferred term TIG, is a process in which fusion welding is accomplished by the heat of an electric arc drawn between a non-consumable tungsten electrode and the work.
- The electrode, arc, weld puddle and the adjacent heated area of the workpiece are protected from atmospheric contamination by an externally applied gaseous shield.
- Filler rod may or may not be added.
With GTAW, the heat of the arc is transferred to the work through a nonconsumable:
a) titanium electrode.
b) carbon electrode.
c) tungsten electrode.
d) ceramic electrode.
c) tungsten electrode.
GTAW requires an inert gas to:
a) shield the weld puddle.
b) cool the ceramic cup.
c) cool the base metal.
d) reduce current resistance across the arc.
a) shield the weld puddle.
GTAW is used primarily when:
a) high deposition rates are required.
b) high heat input is desirable.
c) welding on thick materials.
d) high quality welds are mandatory.
d) high quality welds are mandatory.
For what application would hot wire GTAW be used?
a) where high production welds are required
b) for square butt joints on thin wall tubing
c) for the joining of precision parts
d) where weld quality is of no concern
a) where high production welds are required
State the major difference between hot wire GTAW and cold wire GTAW.
Hot wire GTAW has the wire preheated with an auxiliary AC current prior to the wire entering the weld pool, whereas the cold wire process feeds wire that is at ambient temperature and without an auxiliary power source attached.
In what positions can the GTAW process be used?
a) flat only
b) flat and horizontal only
c) vertical only
d) all positions
d) all positions
Which metal requires a full preheat when welded with the GTAW process?
a) aluminum
b) carbon steel
c) magnesium
d) cast iron
d) cast iron
GTAW has an advantage over SMAW because it:
a) reduces the overall cost of welding.
b) can eliminate the need to use a flux.
c) does not require a skilled operator.
d) uses inexpensive welding equipment.
b) can eliminate the need to use a flux.
The intensity of the ultraviolet light produced by the GTAW process is like ____________ metal arc welding, but is much greater than that produced by the ____________ metal arc welding process.
The intensity’ of the ultraviolet light produced by the GTAW process is like gas metal arc welding, but is much greater than that produced by the shielded metal arc welding process.
When welding with GTAW, you should wear:
a) dark-coloured, tightly woven clothing.
b) light-coloured, open mesh clothing.
c) light-coloured, heavy weight clothing.
d) dark-coloured, synthetic fabric clothing.
a) dark-coloured, tightly woven clothing.
When using GTAW, good ventilation is required to prevent:
a) gamma radiation poisoning.
b) an oxygen deficiency.
c) smoke inhalation.
d) explosive gas mixtures.
b) an oxygen deficiency.
The arc radiation from GTAW reacts with elements in atmospheric air to form:
a) CO (carbon monoxide).
b) CO? (carbon dioxide).
c) O3 (ozone).
d) SO? (sulphur dioxide).
c) O3 (ozone).
Ultraviolet radiation from GTAW can react with chlorinated degreasing solvents to
produce:
a) phosgene gas.
b) sulphur dioxide gas.
c) ammonia gas.
d) ozone gas.
a) phosgene gas.
Pulsing the arc with GTAW is an advantage when:
a) a wide heat-affected zone is required.
b) penetration on thin metals must be controlled.
c) maximum bead width is preferred.
d) high current settings must be used.
b) penetration on thin metals must be controlled.
