2015 KME Flashcards

1
Q

What is the normal operating range for the air brakes on the 2015 KME?

A

90-120

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is the capacity of the def tank on the 2015 KME?

A

5 gallons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the load rating of the tires on the 2015 KME?

A

J

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is the normal range for oil pressure on the 2015 KME?

A

12-30

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

In the 2015 KME, which circuit does the primary air reservoir gauge read?

A

Rear axle brakes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

In the 2015 KME, the reverse indicator light will stay red for how long when indicating “stop”?

A

3 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

In the 2015 KME, the best fuel economy is delivered between what RPM range?

A

1200-1800 rpm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

In the 2015 KME, what eliminates the need for throttle linkage?

A

Electronic foot pedal.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

In the 2015 KME, what is the name of the process in which carbon in the exhaust is collected and burned off?

A

Regeneration

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What are the 2 types of regeneration?

A

Passive- occurs when driving at highway speeds

Active- small amount of diesel is injected into the exhaust stream to generate more heat during normal driving conditions. Exhaust temp may reach 1100-1500 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

In the 2015 KME, the selective catalytic reduction system converts exhaust into what 2 non toxic gases?

A

Nitrogen and water vapor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What makes up the DEF solution?

A
  1. 5% automotive grade urea

67. 7% deionized water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the percent of DEF consumption compared to fuel consumption?

A

2%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

How shall DEF fluid be stored and what is the shelf life?

A

Between 10-90 degrees

2 years

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

When does the “malfunction indicator lamp” illuminate?

A

When there’s a problem with the emissions system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

In the 2015 KME, what does a flashing DPF lamp along with an illuminated check engine light mean?

A

A parked regeneration is required

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

How long does the active regeneration process take?

A

20-40 minutes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

How is active regeneration stopped when in the middle of the process?

A

By releasing the parking brake or tapping the service brake

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Does regeneration affect pumping operations?

A

No

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

During regeneration, how far shall the exhaust be from all objects?

Flammable objects?

A

Keep 2 feet away from all objects

Keep 5 feet from flammable objects

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

When regeneration is complete, how long will the exhaust gasses remain hot?

A

3-5 minutes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

If the engine fails to start within ___ seconds, wait ___ seconds before trying again. If the engine fails to start after ___ attempts, investigate the problem.

A

15 seconds

Wait 15 seconds

4 tries

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Once the engine has started, oil pressure should be 12 psi within how many seconds?

A

10-15

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

Do not shut off the engine if the coolant is over what temperature?

A

195 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

In the 2015 KME the low air warning buzzer sounds when the air pressure drops below what psi?

A

65 psi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

In the 2015 KME, the spring brakes will automatically engage when the pressure in both tanks drops to what psi?

A

40 psi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

In the 2015 KME, in how much time does the engine brake activate?

A

1/4 second

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

When should the jake brake not be engaged?

A

1) When driving on wet streets

2) During pumping operations

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

In the 2015 KME, when does load shedding of the electrical system begin?

A

When the volts drop below 11.9 for 1 minute

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

On the 2015 KME, the floodlights produce how many Lumens?

A

7,000

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

On the 2015 KME, how in the reverse control system designed to fail?

A

In the “safe mode”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q

On the 2015 KME, what does a flashing indicator light indicate on the handheld reverse transmitter?

A

Indicates “low battery”

Replace with 2 C cell batteries

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q

On the 2015 KME, what indicates it is clear to back up with the reverse control system?

A

A green light with 3 high pitched tones

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q

On the 2015 KME, what indicates “Stop!” On the reverse control system?

A

Red light and a low pitched tone.

Red light and tone both last for 3 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q

On the 2015 KME, how long is the “bounce timer” in the seatbelt indicator?

A

2-5 seconds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
36
Q

The front suction relief valve relieves at what psi?

A

250

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
37
Q

The intake relief valve relieves at what psi?

A

250

38
Q

The TFT keystone relief valve relieves at what pressure?

A

300 psi

39
Q

What size are the intake relief valve drains?

A

2.5”

40
Q

What shall NOT be done to the intake relief valve drains?

A

DO NOT cap them

41
Q

On the 2015 KME, what gpm does the wagon battery provide?

A

1250 gpm

42
Q

On the 2015 KME, what are the sizes of the stacked tips that can be used on the wagon battery?

A

2”, 1 3/4”, 1 1/2”, 3/4”

43
Q

What is the first indication that wear is becoming a problem in the pump?

A

When increased RPM is needed to flow the rated GPM.

44
Q

At what percent of capacity and gpm shall the transfer valve be moved from pressure to volume?

A

70% or 1050 gpm

45
Q

When pumping over what psi shall the transfer valve be in pressure?

A

200 psi

46
Q

Can going from pressure to volume be done while pumping?

A

Yes but at less than 75 psi discharge pressure

47
Q

How long does it take for water to fill the pump when dumping the tank?

A

Allow for 30 seconds

48
Q

In order for the relief valve to work, how much difference must there be between intake and discharge pressure?

A

At least 50 psi

49
Q

When pumping, the intake pressure gauge shall always read over how many psi?

A

Over 0

50
Q

When priming, open the priming pump until the main suction gauge reads a vacuum of what?

A

Intake gauge shows At least 20 Hg

Discharge gauge shows some pressure

51
Q

When drafting, if a prime cannot be achieved within ___ seconds, stop and investigate.

A

45 seconds

52
Q

What type of tank is the water tank?

A

500 gallon polypropylene

53
Q

On the 2015 KME, what is the maximum fill rate and psi for the water tank?

A

Max fill rate 500 gpm at 100 psi

54
Q

On the 2015 KME, At what pressure does the relief valve operate?

A

70-300 psi

55
Q

On the 2015 KME, where are the 4 relief valves located and at what pressure do the relieve?

A

(2) 1 on each keystone 300 psi
(1) on the front suction 250 psi
(1) on the suction side of the pump 250 psi. This relief valve can be closed in order to achieve pressure over 250 psi. Valve is behind the access door on the right (off) side panel

56
Q

The foam pro class A system on apparatus can proportion foam between what concentrations?

A

0.1%-3%

57
Q

What is the max operating pressure of the foam system?

A

400 psi

58
Q

What is the minimum gpm needed for the foam pro system to work?

A

30 gpm

59
Q

What will the foam pro system display if the flow requirements exceed the maximum capacity of the foam pump?

A

HI FLO

60
Q

What are the (4) display functions of the foam pro?

A

1) Flow in gpm
2) Total water
3) % of foam
4) Total foam pumped

61
Q

When priming the foam pump, prime can not be achieved if the water pump is pumping over what pressure?

A

100-150 psi

62
Q

What are the dimensions of the suction hose for the foam fill?

A

6’ x 1”

63
Q

The foam fill pump with automatically turn off if now flow is detected for how long?

A

20 seconds

64
Q

On the 2015 KME, what is the max flow and pressure of the wagon battery?

A

Max flow is 1250 gpm

Max pressure is 200 psi

65
Q

On the 2015 KME, what is the max rotational travel of the wagon battery?

What is the maximum and minimum degrees from horizontal?

A

Max rotational travel is 450 degrees (225 each way)

Max vertical stream is 90 degrees
Minimum stream is 45 degrees under horizontal

66
Q

On the 2015 KME, how long is the tether cable for the remote that controls the wagon battery?

A

30’

67
Q

On the 2015 KME, what are the sizes of the stackable tips?

A

2”, 1 3/4”, 1 1/2”, 3/4”

68
Q

On the 2015 KME, at what pressure do the internal drain valves of the wagon battery open/close?

A

Above 5 psi they close

Below 5 psi they open

69
Q

On the 2015 KME, is the stream straightener used with the spray tip on the wagon battery?

A

No

70
Q

On the 2015 KME, when pressing a button on the remote controlling the wagon battery, after how many seconds of holding the button will the motor speed up for faster movement?

A

After 2 seconds of holding the button

71
Q

On the 2015 KME, what is the range of the wireless remote for the wagon battery?

A

500’

72
Q

On the 2015 KME, how is the wireless remote for the wagon battery powered?

How much operating time is left once the power light begins to flash indicating low battery?

A

Powered by (4) AA batteries

When the “power” light begins to flash you have 3 hours of continuous operation left.

73
Q

On the 2015 KME, after how much time of non use will the wireless remote for the wagon battery turn off?

A

5 minutes

74
Q

On the 2015 KME, how many pumps may it take to BEGIN to lift the cab manually?

A

20

75
Q

On the 2015 KME, when lowering the cab, how long shall you continue to lower the cab once it has made contact with the mounts?

A

5 seconds

76
Q

On the 2015 KME, how do you manually cage the brakes?

A

Turn the 1/2” bolt counterclockwise with a 3/4” box wrench until it doesn’t turn anymore

77
Q

On the 2015 KME, prior to manually caging the brakes, what can be done to make the process easier?

A

Push in the yellow knob to release the brakes

78
Q

On the 2015 KME, when viewing the diagnostic codes, after how much time will the system return to normal?

A

10 minutes

79
Q

On the 2015 KME, when using the gear selector to check transmission fluid, what temperature should the fluid be between?

How long shall the rig be stationary for?

A

Transmission fluid should be between 104-220 degrees

Rig should be stationary for at least 2 minutes

80
Q

On the 2015 KME, when checking the transmission fluid manually, a COLD CHECK can be done when the fluid is between what temperature?

A

60-120 degrees

81
Q

What type of gas do the batteries give off in the 2015 KME?

A

Hydrogen gas. Highly explosive

82
Q

In the 2015 KME, what is the capacity of the DEF storage tank?

A

5 gallons

83
Q

On the 2015 KME, when checking the steering box and linkage, how many short movements of the steering wheel should be made?

A

40-60

84
Q

On the 2015 KME, when checking the drive belt, how much tension is allowed midway between the pulleys?

A

Up to 1/2”

85
Q

On the 2015 KME, what discharge gates need to be lubricated?

Where are the zerks located?

How are they lubricated?

A

Discharge gates that don’t have a wheel.

Located behind the access door on the right side pump panel

Lube with a hand pump grease gun. About 5 pumps

86
Q

Tires shall be replaced when the tread reaches what depth?

A

4/32

87
Q

What are the dimensions of the KME’s?

A

29’ long

10’ wide

9’7” tall

88
Q

What is the wheelbase of the KME?

A

182”

89
Q

What is the operating range of the coolant in the KME’s?

A

160-212 degrees

Fan engages at 212 or when in pump

90
Q

What is the normal operating range for the transmission fluid in the KME’s?

A

180-210

91
Q

The 2013-15 KME’s have what engine/transmission?

A

Cummings engine/ Allison transmission

92
Q

What is the engine oil capacity (with filter) of the KME’s?

A

48 quarts