203 a b review

Question 1

what is advantage of isometric drawings over other drawing

Answer 1

seen in all the directions

Question 2

what orientation is always used on isometrics spool sheets

Answer 2

north

Question 2

a precision dimension is usually expressed in what unit?

Answer 2

decimals

Question 3

Can all sides of a oblique drawing be drawn to scale?

Answer 3

no

Question 4

dimensions should always be placed _____ the object for clarity.

Answer 4

outside

Question 5

for general welding work, you should be able to read an imperial rule to the nearest:

Answer 5

1/16

Question 6

which of the following defines a polygon?

Answer 6

closed figure bounded by 3 or more straight lines

Question 7

how are all views shown in an orthographic projection

Answer 7

vertical horizontal and parallel to each other

Question 8

how are are baseline dimensioned

Answer 8

taken from common extension line

Question 9

when tolerance are encountered, it is a good practice to always use the _____ measurements for layout work.

Answer 9

maximum

Question 10

why should t squares only be used from one side of the drafting board?

Answer 10

the board edges are not always parallel

Question 11

what do oblique drawings use foreshortening for.

Answer 11

reduce the dept to make it look more realistic

Question 12

a metric rule is graduated in?

Answer 12

mm

Question 13

what are the three types of pictorial drawings?

Answer 13

perspective oblique isometric

Question 14

how many view are normally used to developed an orthographic projection?

Answer 14

3

Question 15

what views are shown most often in orthographic projections?

Answer 15

top front right

Question 16

which of the following tools would be used to draw vertical and included lines on a drawing?

Answer 16

T-squares set squares

Question 17

how are arcs curves dimensioned?

Answer 17

radius and focal point

Question 18

what is one aspect of perspective drawings?

Answer 18

difficult to draw

Question 19

how do perpendicular lines appear?

Answer 19

90 degree angle

Question 20

should drawings combine fractions and decibels dimensioning?

Answer 20

no

Question 21

what is four-sided figure with two parallel sides called?

Answer 21

trapizoide

Question 22

will title block contain tolerances for drawing?

Answer 22

yes

Question 23

what are the receding lines on an oblique drawing usually drawn at?

Answer 23

45

Question 24

how are low stress stamps identified?

Answer 24

dimpled apperance

Question 25

which of the following are measuring tools?

Answer 25

squares devider trammels

Question 26

how many times should a wraparound, wrap a pipe?

Answer 26

twice ( 2 times)

Question 27

when repeated accuracy in layout is required you would use?

Answer 27

template

Question 28

what are two common methods of marking material for alignment?

Answer 28

center punch, letter stamps

Question 29

what are lines which are drawn perpendicular to horizontal lines called?

Answer 29

vertical lines

Question 30

how are circles dimensioned

Answer 30

diameters location of center

Question 31

to produce drawing smaller than actual size, which type of scale would you use?

Answer 31

reduced scale

Question 32

what happens to the receding lines when foreshortening an oblique drawing 45 degrees ?

Answer 32

half as long as the scale size

Question 33

what are the receding lines on an oblique drawing usually drawn at?

Answer 33

45 degrees

Question 34

what is an oblique line?

Answer 34

any line not horizontal or vertical

Question 35

with conventional dimensioning, how are final sizes determined?

Answer 35

addiction and subtraction

Question 36

how many equal sides does a pentagon have?

Answer 36

5

Question 37

what does the term obtuse angle referrer to?

Answer 37

greater then 90 degrees

Question 38

what view represents a general impression of a simple shape?

Answer 38

pictorial view

Question 39

what is a metric rule graduated in?

Answer 39

mm

Question 40

A title block may contain scale used on the drawing?

Answer 40

yes

Question 41

when objects are drawn to actual size and dimensioned in metric, how would the scale be represented?

Answer 41

1:1

Question 42

what is the difference between eccentric circles and concentric circles?

Answer 42

concentric has a circle in the middle

Question 43

how is a scalene triangle defined?

Answer 43

no equal sides

Question 44

the measurements of an imperial rule are graduated in ______ level of accuracy.

Answer 44

1/16

Question 45

how are the views in an orthographic projection aliened?

Answer 45

vertical, horizontal

Question 46

Running dimensions are similar to which format?

Answer 46

baseline

Question 47

in drafting, what is the purpose of scale?

Answer 47

draw at reduced scale

Question 48

what is straight line not touching the center of a circle but touching the circumference with both ends called?

Answer 48

chord

Question 49

at what angle should leader lines be drawn?

Answer 49

45

Question 50

when is double line layout used for flame cutting?

Answer 50

several adjoining pieces to cut form

Question 51

what does the abbreviation BCD stand for?

Answer 51

bolt center diameter

Question 52

to check curvature while rolling plate etc., what would you use?

Answer 52

template