Chapter 3 - The Way Buildings are Built: Structural Design Features Flashcards
(144 cards)
0
Q
What are some of the sources loads arise from?
A
gravity, wind, earthquakes, and soil pressure
p72
1
Q
What is defined as any effect (or force) that a structure must resist?
A
Load
p72
2
Q
_______ creates a force on a building through the weight of the building components and all its contents.
A
Gravity
p72
3
Q
Force acting to draw an object toward the earth’s center; force is equal to the objects weight.
A
Gravity
p72
4
Q
When air is in motion, it possesses _______ _______ according to the following fundamental relationship.
A
kinetic energy
p73
5
Q
Forces of wind on a building:
- ________ ________ - the impact effect the wind has on a surface. This force may be reduced by streamlining the surface encountered
A
Direct pressure
p73
6
Q
Forces of wind on a building:
- __________ ______ - when wind encounters an object its fluid nature causes it to flow around the object. This exerts a drag effect on the object.
A
Aerodynamic drag
p73
7
Q
Forces of wind on a building:
- ________ ________- a suction effect produced on the downwind side of the building resulting in an outward pressure.
A
Negative pressure
p73
8
Q
The energy possessed by a moving object is ?
A
Kinetic Energy
p73
9
Q
Secondary effects produced by the wind:
- _______ _______ - a back and forth effect due to variations in the velocity of the wind
A
Rocking effects
p73
10
Q
Secondary effects of the wind:
- ________ - wind passing over a surface such as a roof may cause _______ of the surface depending on the velocity of the wind and the harmonic characteristics of the surface.
A
Vibration / vibration
p73
11
Q
Secondary effects of the wind:
- _____-____ _____ - the tendency of wind to dislodge objects from a building
A
Clean-off effect
p73
12
Q
Earthquakes can cause vibrational motion of the surface that subjects buildings to forces known as ______ ______ that can be very destructive, as history has shown.
A
seismic forces
p75
13
Q
________ forces are produced in a structural member when it is twisted
A
Torsional
p76
14
Q
________ forces are movements of relatively large amplitude resulting from a small force applied at the natural frequency of a structure
A
Resonant
p76
15
Q
Soil _________ occurs where the soil is of a loose, sandy nature and is saturated with water.
A
liquefaction
p77
16
Q
The tendency of a body to remain in motion or at rest until it is acted upon by force is called ?
A
Inertia
p77
17
Q
Buildings with geometric ___________ are inherently more susceptible to damage from earthquakes than buildings having a __________ design.
A
irregularities / symmetrical
p77
18
Q
To overcome the difference and possible damage due to height differences in sections of a building a ______ ______ can be designed into the structure between the two sections
A
seismic joint
p78
19
Q
One method to protect a building against earthquake forces is to increase a buildings stiffness through the use of _____ _____ and ______ ______.
A
shear walls and cross bracing
p78
20
Q
Earthquakes
Another method for increasing a buildings stability is to use continuous structures with a high degree of ___________ in their ____________ _________.
A
redundancy / structural frames
p78
21
Q
__________ ________ are typically installed at the connections between columns and beams, and they absorb energy as the structure begins to move.
A
Damping mechanisms
p79
22
Q
A structural element designed to control vibration is called ?
A
Damping Mechanism
p79
23
Q
The basic concept of _____ ________ is to isolate the building from horizontal movement of the earths surface.
A
base isolation
p79
24
* _________ ________ - Create a layer between the building and the foundation, which has a low horizontal stiffness
Elastomeric bearings
p79
25
* ________ _______ - make use of special plates sliding on each other (a less common method of building isolation)
Sliding systems
p79
26
Like the forces caused by wind and earthquakes, the force generated by _____ pressure must be evaluated in the design process.
Soil
p79
27
Soil exerts a _________ pressure against a foundation.
horizontal
p79
28
The pressure exerted by the soil against the foundation is known as _______ _____ pressure.
active soil pressure
p79
29
The force of the foundation against the soil is known as the _______ _____ pressure.
passive soil pressure
p79
30
As the temperature outside a building changes, the structural members at the ________ of the building expand and contract.
periphery
p81
31
Vibration can arise from sources within a building such as _________ _________.
rotating machinery
ex. blower motors for the ventilation system
p81
32
Vibrations can also arise from sources outside a building such as the ?
passing of a freight train
p81
33
________ can occur in wood structural members as the lumber dries over time.
Shrinkage
p81
34
Shrinkage can result in ______ forces at connections between members.
tensile forces
p81
35
The forces on a building resulting from gravity are classified into two types: ?
dead loads and live loads
p81
36
A _____ _____ is the weight of any permanent part of a building.
dead load
p81
37
A dead load has the characteristic of being fixed in ________ and accurately _______.
location / known
p81
38
A ____ _____ is any load that is not fixed or permanent.
live load
p82
39
Force placed upon a structure by the addition of people, objects or weather is called ?
Live load
p82
40
Load that is applied at one point or over a small area ?
Concentrated load
p82
41
____ and ____ can be considered live loads.
Rain and snow
p83
42
The load exerted on a roof from the weight of snow is known as ?
Snow load
p83
43
Frequently, the snow load calculated for a roof may be on the order of ____ to ____ pounds per square foot.
20 to 30 pounds per square foot
p84
44
Water from fire fighting operations can add an additional ?
live load
p84
45
A stream of water discharging 250 gpm introduces ______ pounds of water per minute.
2082 lbs
p84
46
A water depth of 3 inches will impose a load of ____ pounds per square foot.
20.8 lbs
p84
47
In addition to their origin, the loads applied to buildings may be classified as ______ or ________.
static or dynamic
p84
48
Loads that are steady, motionless, constant, or applied gradually are called ?
Static Loads
p84
49
The dead load of a building, the snow load and many live loads are ______ loads.
Static
p84
50
Loads that involve motion are ?
Dynamic Loads
p84
51
Examples of dynamic loads are ?
wind, moving vehicles, earthquakes, vibration, firefighters and falling objects
p84
52
Dynamic loads differ from static loads in that they are capable of delivering __________ to a structure in addition to the _________ of an object.
energy / weight
p84
53
Condition in which the support provided by a structural system is equal to the applied loads?
Equilibrium
p85
54
The forces that resist the applied loads are known as ?
Reactions
p86
55
A beam that is supported at one end is known as a ?
Cantilever beam
p87
56
Projecting beam or slab supported at one end is a ?
Cantilever
p87
57
Exterior loads can create different kinds of interior forces in materials and are classified according to the direction in which they occur in the material:
* _________ tends to pull the material apart
* __________ tends to squeeze the material
* _____ tends to slide one plane of a material past an adjacent plane
Tension
Compression
Shear
p87
58
The direction of the interior forces is important because the strength of materials varies with ?
direction
p87
59
It is commonly recognized that wood has strength in the direction of its ______, which is different from the strength perpendicular to the ______.
grain / grain
p87
60
A material such as _________ has good compressive strength but little tensile strength.
concrete
p87
61
The magnitude of the interior forces that occur in structural members is evaluated by a quantity known as ______.
stress
p87
62
Stress is a measurement of ______ _______ and is expressed as force units divided by the area over which the force is applied.
force intensity
p87
63
Point at which material ceases to perform satisfactorily. Depending on the application this can be breaking, permanent deformation, excessive deflection or vibration.
Failure point
p88
64
An ____ load is a load applied to the center of the cross-section of a structural member and perpendicular to that cross section.
axial
p88
65
An _______ load is a load that is perpendicular to the cross section of the structural member but does not pass through the center of the cross section.
eccentric
p89
66
A ________ load is offset from the center of the cross section of the structural member and at an angle to or in the same plane as the cross section.
torsional load
p89
67
Structural member subjected to loads, usually vertical, perpendicular to its length ?
Beam
p90
68
At the middle of the beam, a point known as the neutral axis, the tension and compression stresses are actually _____.
zero
p91
69
_____ beams are capable of supporting greater loads than _____ beams, even if they have the same cross-sectional area.
Tall / short
p93
70
Vertically supporting members are called ?
Columns
p93
71
An _____ is a curved structural member in which the interior stresses are primarily compressive.
arch
p93
72
______ can be thought of as flexible structural members that can be used to support roofs, brace tents, and restrain pneumatic structures.
Cables
p94
73
A cable used to support loads over a great distance will assume the shape of a ?
parabola
p94
74
______ are framed structural units made up of a group of triangles in one plane.
Trusses
p95
75
Typical truss shapes are available to span distances of ___ to ___ feet, but in today's construction truss spans in excess of ____ feet are not uncommon.
22 to 70 feet / 100 feet
p96-97
76
Lightweight wood or metal trusses, known as truss joist, have become very common in ______ construction, taking the place of solid joists.
floor
p97
77
Lightweight wood trusses are also commonly used in _____ construction.
roof
p97
78
From a fire fighting standpoint, trusses have the potential for early ?
failure under adverse conditions
p97
79
_____ ______ are truss structures that are developed in three dimension.
Space frames
p97
80
The _________ in truss assemblies are a critical part of the truss.
connectors
p98
81
Wall that supports itself and the weight of the roof and/or other internal structural framing components such as the floor beams above it.
Bearing wall
p98
82
In a ______ structure, structural support is provided in a manner similar to the way the skeleton supports the human body.
frame
p99
83
When the joist between a column and a beam are reinforced so bending stresses can be transmitted through the joints, the structural system is known as a ?
rigid frame
p100
84
_____ and ______ frames are most frequently encountered in concrete structures.
Slab and column
p101
85
System of construction in which the building consists primarily of an enclosing surface and in which the stresses resulting from the applied loads occur with in the surface bearing wall structures is called ?
Surface System
p101
86
Structure with an enclosing surface of a thin stretched flexible material. Examples of these are a simple tent or an air-supported structure.
Membrane Structure
p101
87
Rigid, three-dimensional structure having an outer "skin" thickness that is small compared to other dimensions is called ?
Shell Structure
p102
88
Determining the type and magnitude of the ________ to which the structure will be subjected is the most critical aspect of engineering design.
forces
p 71
89
The air that makes up the atmosphere is a gas that, like all substances, has ________.
mass
p 73
90
Wind
The "clean-off effect" noted above is of particular concern where a building has projections such as _________ and _________.
canopies and parapets
p 73
91
Wind
In designing buildings to withstand the force of wind, the primary effect considered is the force due to __________ ___________.
direct pressure
p 73
92
Wind
The force resulting from wind is particularly dangerous when it occurs against an _________ ________. Situations of this type can occur at ______________ sites.
unbraced wall / construction
p 74
93
- Forces developed by earthquakes. These are some of the most complex forces exerted on a building.
Seismic Forces
p 75
94
Earthquakes
In some areas, the design professional needs to give little or no special consideration to seismic loads because the structural provisions for ________ or _______________ loads are adequate for likely seismic loads.
wind or gravitational
p 75
95
Earthquakes
The vibrational motion produced by earthquakes can be _______-_____________.
three-dimensional
p 75
96
The magnitude of the forces developed within a building during an earthquake depend on several factors, including the following:
* Magnitude of the __________ __________
* Type of _____________
* Nature of the _______ under the building
* ___________ of the structure
* Presence of __________ mechanisms within the building
* vibratory motion
* foundation
* soil
* stiffness
* damping
p 76-77
97
Although the movement of the ground beneath a building can be three-dimensional, the ____________ motion is the most significant force.
horizontal
p 77
98
As the ground moves under a building, _________ tends to keep the upper portion of the building momentarily in its initial position.
inertia
p 77
99
Earthquakes:
Increasing the ____________ of a building reduces its susceptibly to ground motions that have a relatively long (meaning slow) vibrational period.
stiffness
p 78
100
Earthquakes
Buildings designed with ____________ structural frames are less likely to collapse if one member fails.
redundant
p 79
101
Earthquakes
Damping mechanisms operate on a principle similar to the manner in which a _______ closer controls the speed of a _______.
door / door
p 79
102
Elastomeric bearings
The bearings are made of either ________ _________ or _________.
natural rubber or neoprene
p 79
103
Soil pressure
In determining the force created by active soil pressure, the soil is assumed to behave like a ________.
fluid
p 80
104
In addition to the forces already discussed, other forces arising from ______________ ________, ___________ and __________ also may be exerted on a building.
temperature change, vibration, and shrinkage
p 81
105
- Weight of the structure, structural members, building components and any other feature permanently attached to the building that is constant and immobile. Load on a structure due to its own weight and other fixed weights.
Dead load
p 81
106
Earthquakes:
Increasing the ____________ of a building reduces its susceptibly to ground motions that have a relatively long (meaning slow) vibrational period.
stiffness
p 78
107
Earthquakes
Buildings designed with ____________ structural frames are less likely to collapse if one member fails.
redundant
p 79
108
Earthquakes
Damping mechanisms operate on a principle similar to the manner in which a _______ closer controls the speed of a _______.
door / door
p 79
109
Elastomeric bearings
The bearings are made of either ________ _________ or _________.
natural rubber or neoprene
p 79
110
Soil pressure
In determining the force created by active soil pressure, the soil is assumed to behave like a ________.
fluid
p 80
111
In addition to the forces already discussed, other forces arising from ______________ ________, ___________ and __________ also may be exerted on a building.
temperature change, vibration, and shrinkage
p 81
112
- Weight of the structure, structural members, building components and any other feature permanently attached to the building that is constant and immobile. Load on a structure due to its own weight and other fixed weights.
Dead load
p 81
113
___________ distributed loads must have structural support to counter the different stresses.
Unevenly
p 83
114
An industrial paper cutter is an example of a _____________ load.
concentrated
p 83
115
A building collapses or partially collapses - when the _________ loads exceed the ability of the structural system to support them. The collapse represents a loss of ____________.
applied / equilibrium
p 85
116
The loads and forces applied to a structural member creates __________ _________ within the member.
internal forces
p 86
117
Internal forces - stress
This bending force is known as a ___________ ___________ and is equal to the force multiplied by the distance at which the bending moment is applied.
bending moment
p 87
118
- Those vertical or horizontal forces that tend to pull things apart; for example the force exerted on the bottom chord of a truss.
Tension
p 87
119
In the design of structures, the _________ within structural members must be kept below the _________ at which the material being used would fail.
stresses / stresses
p 88
120
Stresses
It is typical for stresses to occur in ______________ within an individual member.
In the beam shown in figure 3.27, the applied load creates ________ stress in the bottom of the beam and ___________ stresses in the top of the beam.
combination / tension / compressive
p 88
121
Stress
Exterior loads can also be classified as _______, __________, or ___________ according to the manner in which they are applied.
axial, eccentric, or torsional
p 88
122
Stress
Axial loads are applied along the members ______.
axis
p 89
123
Stress
Eccentric loads are applied to one side of the cross section, creating a ___________ tendency.
bending
p 89
124
Stress
Torsional loads are applied at an angle to the cross section, creating a ___________ tendency.
twisting
p 89
125
A _______ is a structural member that can carry loads perpendicular to its longitudinal dimension.
beam
p 90
126
A ________ ___________ beam is supported at each end and is free to rotate at the ends.
simply supported
p 90
127
A _____________ beam is supported at one end.
cantilever
p 90
128
______________ beams are rigidly supported at each end.
Restrained
p 90
129
If a beam supports loads, the top of the beam is subjected to _______________ stresses and the bottom of the beam is subjected to __________.
compressive / tension
p 91
130
The maximum compression and tension stresses in a beam occur in the ______ and ________ of the beam.
top and bottom
p 92
131
In an I-beam, the top and bottom portions of the beam are known as the top and bottom ________.
flanges
p 92
132
___________ are structural members designed to support an axial compressive load.
Columns
p 93
133
Arches are designed to carry loads across a __________ and have application as support for roofs and entrances in masonry buildings.
distance
p 93
134
- Structural member used to form a roof or floor framework. These form triangles or combinations of triangles to provide maximum load bearing capacity with a minimum amount of material; often rendered dangerous by exposure to intense heat, which weakens gusset plate attachment.
Truss
p 95
135
The top members of a truss are called the _____ _______ and the bottom members are called the ________ ________. The diagonal members are called either ___________ or _____ __________.
top chords / bottom chords / diagonal or web members
p 96
136
Lightweight _______ trusses, known as ______ _________, are also used for floor and roof construction in fire-resistive and non combustible construction.
steel / bar joists
p 97
137
Failure of a ____________ will result in failure of the truss.
connector
p 98
138
A common method of construction use the ________ of a building to support spanning elements such as beams, trusses, and precast concrete slabs. These are appropriately known as ________ _______ structures.
walls / bearing wall
p 98
139
In a bearing wall structure, the walls are subjected to __________ loads.
compressive
p 98
140
________ _______ wall construction uses relatively closely spaced vertical steel studs connected by top and bottom horizontal members.
Steel stud
p 99
141
_______ and _______ construction uses a series of vertical elements to support horizontal elements.
Post and beam
p 99
142
Post and beam:
The vertical posts may be spaced up to _____ inches apart, unlike stud wall construction where the studs are ____ to ____ inches apart.
24 / 12 to 16
p 100
143
A power station cooling tower is an example of a _______ _________.
shell structure
p 102
