*'93 Simon-LTI

Question 1

‘93 Simon- Transmission temp normal operating range?

Max temp before needing to cool trans oil via high idle?

Answer 1

160°-220°F

250°F, if cooling procedures fail, notify shops

Question 2

‘93 Simon LTI- how long is the electrical cord reel mounted on the apparatus?

unknown

Answer 2

200 ft

Question 3

On the ‘93 Simon-LTI, below what PSI will the “Low Air Pressure” indicator light illuminate?

Answer 3

60

Question 4

‘93 Simon- How many quarts of 15w-40 engine oil are needed for an oil change including the oil filter?

Answer 4

44 qts

Question 5

‘93 Simon- Normal voltage operating range with engine running?

different from other rigs

Answer 5

13.8-14.2v

Question 6

‘93 Simon- Normal engine coolant operating range?

Answer 6

160°-190°F

Question 7

On the ‘93 Simon-LTI, the high water temperature indicator light will illuminate at what degrees?

Answer 7

220 degrees F

Question 8

‘93 Simon- Normal oil pressure operating range @idle, @1200 rpm and @2100 rpm?

Answer 8

10 psi min @ idle

35psi min @1200

45 psi min @ rated 2100 log book also states 40-50 rpm @2100

Question 9

On the ‘93 Simon-LTI, if the “Air Cleaner Gauge” reads ___ inches of H2O, check for restrictions at the filter intake screen and notify shops if problem was not solved.

Answer 9

25 inches h20

Question 10

‘93 Simon LTI- what two degrees will the “Approaching Jackknife” indicator light illuminate?

Answer 10

62° and 90°

Question 11

‘93 Simon- How many quarts of 15w-40 engine oil are needed for an oil change not including the oil filter?

Answer 11

38 qts

Question 12

‘93 Simon- Length and width of apparatus?

unknown

Answer 12

Length- 54’10”

Width- 10’

Question 13

On the ‘93 Simon-LTI, the “Low Engine Oil Pressure” indicator light illuminates when oil pressure drops below what psi?

Answer 13

3 psi

Question 14

On the ‘93 Simon-LTI, what is the normal operating range for engine rpm?

Also, The driver should manually keep the rpm’s between ____ and ____ when driving

Answer 14

1100-1600 rpm

1550-2100 rpm

Question 15

‘93 Simon LTI- What is the total outrigger spread when fully deployed?

unknown

Answer 15

16 ft

Question 16

‘93 Simon- fuel rank capacity?

Answer 16

50 gal

Question 17

On the ‘93 Simon-LTI, what is the maximum air restriction for a CLEAN “Air Cleaner Gauge”?

Answer 17

10 inches h20

Question 18

‘93 Simon- Due to the nature of this engine, it may take more than ___ seconds of engine cranking to start.

Answer 18

5 secs

Question 19

‘93 Simon LTI- A red warning light (no audible alarm) will illuminate when transmission temperature reaches ____ degrees F.

Answer 19

250°F

Question 20

‘93 Simon- Due to the heat output created by the tillerbucket heater exhaust, keep objects away at least ___ inches

Answer 20

6”

Question 21

‘93 Simon: what is the tire psi for the front/rear/tiller tires?

Answer 21

110 front
90 rear
110 tiller

Question 22

‘93 Simon Rockwell brake system:

1. The disc brake system uses pads that are different thicknesses for the REAR brakes. Which pad is thinner and which is thicker? (Ie; inside pad vs outside pad) Also, what are the sizes of brake pads when new?
2. The FRONT brake pads, inner and outer, are identical, both are ____ of an inch when new and normally appear to be wearing at the same rate.

Answer 22

1. Inner pad is thicker (new 7/8”)
   Outer pad is thinner (new 9/16”)
   The rotor compensates for this difference by being thicker on the outboard side and thinner on the inboard side.
2. 5/8”

Question 23

For a ‘93 hot engine shutdown (water temp operating range high):

Run rig at 900 to 1100 rpm (high idle) for 3 to 5 minutes or until temperature returns to normal, and then run it at idle for ____ seconds before shutdown.

Answer 23

30

This lets the oil carry away heat by circulation and gives the turbo time to cool

Question 24

‘93 Simon:

The outriggers should operate from the stowed to deployed position in ____ seconds or less

Answer 24

90

Question 25

‘93 Simon:

The tread wear bar indicator is the raised rubber portion located at the bottom of each tread groove, approximately ___ to ____ inches apart, around the circumference of the tire.

What is the width and height of the tread wear bar?

Answer 25

6 to 20”

1/2” wide by 3/32” high

Question 26

‘93 Simon logbook:

Problems are likely to result if tires on a dual assembly differ by more than ____ inch in diameter.

Answer 26

1/2”

If a slight mismatch does occur, the smaller of the two tires should be installed on the inside. The most accurate way to measure an inflated tire is to measure the circumference with a steel tape.

Question 27

‘93 Simon- Height of tiller cab, front cab, and full tilted cab?

unknown

Answer 27

Unknown
Tiller- 11’8”

Front cab- 10’5”

Full tilted cab- 16’2”