Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

truck > *Logbooks LTI Aerial Ladder > Flashcards

*Logbooks LTI Aerial Ladder Flashcards

1
Q

What diameter are the K-braced rungs on the LTI aerial?

A

1 1/2”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How far apart are the rungs spaced apart on the LTI aerial?

A

14” on center

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the retracted length of the LTI aerial?

A

31’8”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is the extended length of the LTI aerial?

A

94’

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What is the total reach for the LTI aerial when fully extended?

A

100ft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

LTI aerial- The hydraulic pump is an axial piston, variable displacement type pump with a capacity of ___ gpm.

A

20 gpm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

LTI aerial- Hydraulic oil is supplied from an all steel reservoir with a capacity of ___ gallons.

A

40 gal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

LTI aerial- The ladder elevation ranges from ___º to ___º

A

-4° to 75°

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The variable displacement type pump that provides hydraulic oil to the LTI aerial will create ____ psi and approximately ___ gpm.

A

2800 PSI and 20 GPM

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

LTI aerial- When is the emergency power unit (EPU) used?

A

When there is hydraulic or electrical failure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Personnel on the LTI aerial should be spaced how far apart?

A

10 ft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Is the LTI aerial designed with its maximum strength in the supported or unsupported configuration?

A

Unsupported

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

LTI aerial- Position the ladder approximately ___ to ___ inches above the objective.

A

6-12 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Always keep the aerial ladder at least ___ feet away from all electrical wiring.

A

10 ft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Do not operate an extended aerial in wind conditions exceeding ___ mph.

A

30

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

On grades between 6% and 14% (3.5º and 8.0º) capacities of the aerial are reduced by ___%

A

50%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

On grades between ___ and ___degrees, capacities of the aerial are reduced by 50%

A

3.5 and 8 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

On grades between ___% and ___%, capacities of the aerial are reduced by 50%

A

6% and 14%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Operating the LTI aerial on grades in excess of ___% (or ___ degrees) is prohibited.

A

14%

9 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

In relation to the aerial load chart, the turntable of the aerial is considered level if the street grade is less than ___% or ___ degrees

A

6% or 3.5°

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

The fast idle switch at the outrigger control box will set the engine speed between ____ and ____ rpm.

A

1500-1600 rpm

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

‘03 ALF- When the load on the aerial is between ___% to ___%, 19-20 bars will illuminate on the “Aerial Loading Warning Display”. The display will also begin to flash.

A

90-100%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

‘03 ALF Aerial Loading Warning Display - When the max load on the aerial is exceeded by ___ to ___lbs, an alarm on the pedestal will sound.

A

50-100lbs

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

LTI aerial- the outrigger system relief valve relieves at _____ psi

A

2000 psi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

LTI aerial- For the apparatus level indicator, yellow indicates ____ percent operating capacity. (___ to ___degrees)

A

50%

3.5° to 8°

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

LTI aerial- The green, yellow and red marks on the Apparatus Level Indicator represent what operational limitations?

A

Green- full operating capacity
Yellow- 50% operating capacity
Red- aerial operation prohibited

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

LTI aerial- In the event of an electrical failure, once activated, the _______ allows hydraulic fluid to the outrigger valve bank and aerial controls

A

Manual Circuit Selector (blocking solenoid valve)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

‘03 ALF- When the load on the aerial is ___%, 18 bars will illuminate on the “Aerial Loading Warning Display”. The display will also begin to flash.

A

80%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

‘09 ALF- The anchor attachments points on the 5th wheel have a rating of ______ lbs.

A

9000 pounds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

‘06 and ‘09 ALF LTI- While using the EPU and the rotation interlock override, The aerial can be moved ___ to ___ degrees past the tiller cab toward the short set side and ___ degrees past the tractor cab toward the short set side.

A
  1. 8-10 degrees

2. 2 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

What is the tip load rating on all LTI aerials?

A

250 lbs

32
Q

LTI Aerial- The Hydraulic System Pressure Gauge registers working pressure in the system from zero to _____ psi.

A

5000

33
Q

LTI Aerial- The pressure in the hydraulic system to hoist the aerial should not exceed _____ psi

A

2800

34
Q

LTI Aerial- The pressure in the hydraulic system to rotate the aerial should not exceed _____ psi

A

1500

35
Q

LTI Aerial- The pressure in the hydraulic system to extend or retract the aerial should not exceed _____ psi

A

2000

36
Q

LTI Aerial- The inclinometer at the base of the aerial is a floating ball-type angle indicator calibrated from ___ to ___ degrees.

A

-20 to +80 degrees

37
Q

LTI Aerial- Located along the handrails of the main section are extension indicators marked off in ___ foot increments.

A

5

38
Q

LTI Aerial- An “over the rear” aerial throw is defined as angles up to and including ___ degrees to either side of the apparatus centerline.

A

45 degrees

39
Q

LTI Aerial- If on a hill, chock blocks for an aerial operation should be placed where?

A

Downhill side of front and tiller tires

40
Q

LTI Aerial- The “outrigger fully deployed” green light on the outrigger control box will illuminate when an outrigger is fully deployed and pressure being applied to the ground is a minimum _____ lbs.

A

800

41
Q

The proper method for deployment of the outriggers is to relieve the weight from the tractor’s ________, allowing the load forces to be absorbed by the aerial _____ and chassis frame.

A

Rear springs

Torque box

42
Q

LTI Aerial Outriggers- When inserting the locking pin choose a hole that is a minimum ___ inch below the jack skirt, then back pin out ___ inch

A

1/4”

1/2”

43
Q

LTI Aerial- What should you do if the apparatus turntable cannot be leveled without the outriggers raising the tires?

A

Do not level turntable and operate within the reduced capacities

44
Q

‘06 and ‘09 ALF LTI- With the equipped aerial “rotation limiting system”, both rotational directions are allowed but swinging toward the short jacked side will be cut-out after approximately ___ degrees of rotation.

In an emergency, how would you override this feature?

A

4 degrees

Activate the blocking solenoid and rotation interlock override.

45
Q

‘06 and ‘09 ALF LTI- In the event of electrical failure at the pedestal, what two override features must be activated in order for aerial operation?

A
  1. Blocking solenoid valve

2. Rotation Interlock Override

46
Q

LTI Aerial- The EPU is a 12-volt dc electric motor and a ___ gpm at _____ psi pump

A

1.5 gpm

2000 psi

47
Q

LTI Aerial- What in cab switch should be turned off prior to utilizing the EPU?

A

Aerial PTO

48
Q

‘95 Simon to ‘03 ALF LTI Aerial- The EPU is rated for a maximum of ___ minutes continuous operation

A

3

49
Q

‘95 Simon to ‘03 ALF LTI Aerial- The EPU can be used over a long period of time at a ___% duty cycle. This % equates to ___ seconds every ___ minutes.

A

7%

21 sec every 5 min

50
Q

‘06 and ‘09 ALF LTI Aerial- The EPU is rated for a maximum of ___ minutes continuous operation

A

7 min

51
Q

‘06 and ‘09 ALF LTI Aerial- The EPU can be used over a long period of time at a ___% duty cycle. This duty cycle equates to ___ minutes use in every ___ minutes ( which equals ___ minutes on and ___ minutes off).

A

23% cycle

  1. 3 and 10
  2. 3 on / 7.7 off
52
Q

LTI Aerial- what is the max system pressure for the aerial hydraulic system?

A

2800 psi

53
Q

‘93 Simon LTI Aerial only- The load gauge at the pedestal will read what color when the ladder has a forward load?

A

Green. Should normally be this color during normal aerial/ladder pipe operations

54
Q

‘93 Simon LTI Aerial only- The load gauge at the pedestal will read what color when the ladder has a rearward load?

A

Orange. This occurs when:

(1) the aerial is powered into an obstruction
(2) when there is extremely high nozzle pressure from a ladder pipe operation
(3) during normal bedding of the aerial into the cradle.

55
Q

LTI Aerial: outriggers

Deploy the first outrigger out and down on the low side until the bubble in the aerial leveling indicator moves just past level or ____ of an inch

A

1/8”

56
Q

LTI Aerial:

Extension and retraction of the aerial is provided by dual, extension/retraction _____ and _____ drive combination.

A

Cylinders

Cable

57
Q

LTI Aerial:

An automatic ____ type brake is used to stop the rotation of the aerial.

A

Disc

58
Q

LTI Aerial:

Electrical power is supplied by the tractor’s electrical system. The aerial electrical system is a ____ wire; negative ground return type, utilizing the apparatus frame as ground

A

Single

59
Q

LTI Aerial:

Power from the tractor’s system is transferred to the aerial through what?

A

Electrical swivel coupling

The coupling consists of numerous sets of brushes and brush holder assemblies, collector rings and connectors which provide uninterrupted current flow to the aerial circuits through 360º of aerial rotation

60
Q

LTI Aerial:

The power take off (PTO) switch is an electric switch that energizes a _____, which allows transmission fluid to the PTO

A

Solenoid

61
Q

Aerial operating capacities are governed by what?

A

The Aerial Load Chart

62
Q

LTI Aerial:

An anti-friction ____ and ring gear attaches the aerial ladder to the trailer and permits 360º continuous of rotation

A

Ball Bearing

63
Q

The construction for the outriggers are double box horizontal ____ and vertical ____

A

Beams

Jacks

64
Q

For emergency response the beam IN and jack UP can be operated simultaneously after jack pressure is _____

A

Released

Beam control and jack control switches shall be operated as a single function to watch each beam and jack extend and/or retract

65
Q

If at anytime the road transmission is shifted into gear while performing
aerial operations, the _____ will automatically disengage the PTO

A

Chelsea Hot Start

66
Q

True or False?

The outrigger interlock override system is designed to allow use of the aerial in situations where lives are at risk and no other options are available

A

True

67
Q

Outrigger Operation: Override/Emergency Operation

Prior to actuating the applicable button(s) on the outrigger valve bank,
the _____ handle must be pulled and held in the actuated position, for the duration of the outrigger operation.

A

4 way solenoid

This manually shifts the blocking solenoid valve, shutting off the oil to the aerial system and directing the flow to the outrigger valve bank.

68
Q

When using the EPU, The system is capable of all functions in a ____ load condition

A

No load condition

69
Q

‘03 ALF Aerial:

The Class 1 Aerial Loading Display is designed to warn aerial operators of dangerous loading conditions when the aerial device is operated at ____ (low or high?) angles of elevation.

A

Low

70
Q

Lockout cylinders:
There are times when the drive axle might be sitting higher or lower than the steering axle (i.e. uneven pavement). In these instances, either the two front or two rear lockout cylinders will not make contact with the fifth wheel once fully extended. Does this reduce the capacity of the aerial ladder?

A

No, all functions and limitations are the same

71
Q

‘09 ALF Aerial:

The capstan has a _____ lb rating

A

250

72
Q

‘09 ALF Aerial:

When using the wench system, turning the handle _______ provides more torque for heavy lifting at slower speeds and _______ provides faster lifts but for lighter loads.

A

Clockwise

Counterclockwise

73
Q

‘09 ALF Aerial wench system:

To start, wrap the rope around the mechanical winch in a _____ direction (when looking down on the unit from the top) ____ to ____ times starting at the bottom and working up.

A

Clockwise

4 to 5

74
Q

Actual operating time of the EPU is dependent upon what two criteria?

A
  • batteries state of charge

- hydraulic pressure in control being moved

75
Q

In the event of an electrical failure, the outrigger controls and the aerial controls will become disabled because of the _____ system.

A

Interlock

76
Q

What are the height of the handrails on the LTI aerial?

A

15”

truck (145 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions