2010 KME Log Book Info

Question 1

The MDT will continue to draw electrical current _____ even though the battery master switch is turned _____.

Answer 1

(approximately 7 to 8 amps) / OFF.

Question 2

Air Cleaner Restriction Gauge:

Maximum inlet restriction for a new air cleaner is ____. If the gauge reads ____ check for restrictions.

Answer 2

10” H2O / 25” H2O,

Question 3

The best fuel economy is delivered between ____.

Answer 3

1200 – 1800 RPM

Question 4

When the engine is cold, this additional RPM could be very harmful due to ____ and due caution should be exercised.

Answer 4

minimal lubrication

Question 5

Do not idle in R (Reverse) for more than ____. Extended idling in R (Reverse) may cause ____.

Answer 5

five minutes / transmission damage.

Question 6

Do not idle in D (Drive) for more than _____. Extended idling in D (Drive) may cause transmission damage.

Answer 6

five minutes

Question 7

Gear 1 = RPM / Speed

Answer 7

2100 / 14 mph

Question 8

Gear 2 = RPM / Speed

Answer 8

2100 / 26 mph

Question 9

Gear 3 = RPM / Speed

Answer 9

2100 / 36 mph

Question 10

Gear 4 = RPM / Speed

Answer 10

2100 / 54 mph

Question 11

Gear 5 = RPM / Speed

Answer 11

2000 / 66 mph

Question 12

Gear 6 = RPM / Speed

Answer 12

1700 / 66 mph

Question 13

A good indicator that all of the moving parts are getting lubrication is when the oil pressure gauge registers pressure ____ at idle speed.

Answer 13

(at least 10 psi)

Question 14

If there is no oil pressure indicated within ____ , stop the engine and check the lubricating system. The pressure should not fall below ____ and normal operating pressure should be higher.

Answer 14

10 to 15 seconds / 30 psi at 1200 rpm

Question 15

Incomplete combustion of fuel is the end result of this, which can cause crankcase dilution, formation of_____ on the valves, pistons, and rings, and rapid ____ in the engine.

Answer 15

lacquer or gummy deposits / accumulation of sludge

Question 16

When on scene with all warning lights activated, engage the engine high idle feature. Doing so will assist the ____ in keeping up with the electrical current demands placed on it and prevent the Load Manager from “cutting out” electrical accessories due to insufficient current flow.

Answer 16

alternator

Question 17

Try not to shut down the engine unless coolant temperature is____.

Answer 17

195 F or less.

Question 18

Stopping a turbocharged engine immediately after high-speed operation may cause damage to the turbocharger as it will continue to turn without an _____.

Answer 18

oil supply to the bearings.

Question 19

If air pressure is reduced to approximately ___ in both systems, the spring brake valve will automatically apply.

Answer 19

40 psi

Question 20

Do not engage the Jake Brake on _____. The additional braking effort on the drive wheels (duals) can cause them to lock up which could result in an uncontrollable skid.

Answer 20

wet streets

Question 21

After the battery voltage drops to a preselected setting approximately_____, the engine throttle will be ____ to compensate for the low voltage and electrical system loads.

Answer 21

12.8 volts / increased

Question 22

The fast idle output will remain ON for a minimum of ____and until ____ is achieved.

Answer 22

10 minutes / 13.0 VDC

Question 23

An alarm sounds if a low-voltage condition (below ____) develops.

Answer 23

11.9 volts

Question 24

If the low-voltage condition continues (for approximately ____), then the shedding of electrical loads will begin.

Answer 24

1 minute

Question 25

A ____ is the voltage that will cause a load to be turned off if the system voltage drops to this point.

Answer 25

shed point

Question 26

An ____ is the voltage that must be achieved before a load is turned back on once it has been shed

Answer 26

unshed point

Question 27

A shed system (load) will not be recognized for ___ or until the unshed voltage setting is maintained for ____.

Answer 27

5 minutes / 1 minute

Question 28

The fast idle system will be maintained for a minimum of ___ and until a voltage reading of ___ even if any system shedding did not occur.

Answer 28

10 minutes / 13.0 is achieved,

Question 29

When ALL electrical accessories are turned on and engine is running at idle (_____), the ____ will be unable to keep up with the electrical demands placed on it thereby causing the air conditioning to be turned off.

Answer 29

500-750 rpm / alternator

Question 30

Manual Pump Shift Procedure:

3. Move cab pump shift lever to the ______.
4. Shut down engine.
5. Pull ______ (located on right side pump panel).

Answer 30

center position / manual pump shift override handle

Question 31

Manual Pump Shift Procedure:

6. Start engine.
7. Place the _____ (right of steering column) in the “ON” position.
8. Shift transmission into D (Drive).

Answer 31

emergency override switch

Question 32

The apparatus is equipped with _____ intake pressure relief valves; one which has been preset at ____ and two which have been set at ____

Answer 32

4 / 300 psi / 250 psi

Question 33

The actual relief valve is bolted onto the bottom portion of the B.I.V. and relieves any pressure in excess of _____ that is pumped from another source to the inlet of the B.I.V

Answer 33

300 psi

Question 34

This valve is located before the front suction valve. This intake relief valve will relieve pressure in excess of ___ even with the front suction in the closed position.

Answer 34

250 psi

Question 35

The fourth intake pressure relief valve is located on the _____.

Answer 35

suction side of the pump.

Question 36

Foam % = Max GPM

0.2% = GPM

Answer 36

1300

Question 37

Foam % = Max GPM

0.5% = GPM

Answer 37

520

Question 38

Foam % = Max GPM

1.0% = GPM

Answer 38

260

Question 39

Foam % = Max GPM

3.0% = GPM

Answer 39

85

Question 40

The maximum operating pressure of the Foam Pro Model 2001 Foam System is ____.

Answer 40

400 psi

Question 41

The minimum GPM flow needed to operate the Foam Pro System is ______.

Answer 41

30 gpm