ATA 29 - HYDRAULICS Flashcards

(36 cards)

1
Q

The Hydraulic system is how many systems?

A

Two. The Resovior/Valve block, and the Pumps

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How many releif valves per system?

A

Two. One High Px, One Low Px.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What Px is the High Px releif valve?

A

122 bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What Px is the Low Px releif valve?

A

7.5bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

How many filters are in the Hydraulic system?

A

Two - One per valve block.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What type of pump are the hydraulic pumps?

A

Pistion type pumps.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is the operating Px of the Hydraulic system?

A

103 bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the Hyd Module frame made of?

A

Milled Aluminium

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What changes with Hydraulic demand, Px or flow?

A

Flow. The Px always stays the same.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

How does the flow increase in the Hyd system?

A

by the angle of the backplate in the pump

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

How many main actuators are there?

A

3 double actuators.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

How many Hyd pumps are in the system?

A

One per system.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is the use of the actuators?

A

To turn hyraulic Px into mechanical Px.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Which system has the TR shut-off valve?

A

System 1.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

when does the TR shut-off vlave close?

A

when there is less than 0.19litres of flud left in the resovoir.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What is the pre-load (resovoir) Px?

A

1.4-.1.75 bar

17
Q

How many lines are connected to each pump?

A

Four. Suction Line (S) from the resovoir, Output Line (P) to the system, Case Drain (Sc) providing a minimum flow around the pump to provide cooling and lubrication, and the Seal Drain (Sd) connected to the seal drain ofr the pump seal.

18
Q

Where is the seal drain connected to?

A

the overboard drain.

19
Q

What is the capacity of the Hyd system?

20
Q

What are the Hyd pumps driven from?

21
Q

How is system flow increased?

A

By increasing the pump stroke.

22
Q

What is the sight glass for on the Resvoir?

A

For checking to see if there is air in ther hyd system

23
Q

Where is non-return valve located?

A

in the resvoir block after the line from the pump, and before the filter.

24
Q

How is the fluid level checked?

A

By the level indiactor located on the front of the resovoir.

25
What is the resovoir capacity?
0.8litres
26
What Px does the LOW HYD Px caution illuminate?
69 BAR
27
When does the LOW HYD Px caution extinguish?
83 BAR
28
The three support levers belong to what section of the system?
the NON-BOOSTED control section
29
Which Hyd system has an additional Px switch?
System 1 - for the TR Actuator.
30
When will the TR SHUT OFF caution illuminate?
When the level drops below 0.19 litres in the system 1 resovoir and the TR shut-off valve closes.
31
When can the HYD TEST be c/o?
On the ground only.
32
What happens when the HYD SYS 1 TEST is activated?
The solonoid valve of System 2 is energised and closed, giving a LOW PRESS HYD 2 caution.
33
Which modal has an Electric Hyd pump?
The D3.
34
What is the purpose of the E-HYD pump?
for ground test of the flight controls only.
35
What Px does the E-HYD pump provide?
80-100 bar
36
Which system does the E-HYD pump run off?
System 1.