final

Question 1

What type of rope is preferred for tiedown of small aircraft?

Answer 1

Nylon And Decron

Question 2

A drawing showing subassemblies brought together is called an installation drawing T/F

Answer 2

True

Question 3

A detail drawing is a class of working drawing that is the depiction of a single part. T/F

Answer 3

True

Question 4

An Orthographic projection can present as many as ____ Views

Answer 4

6

Question 5

A pictorial diagram uses electrical symbols instead of images of components T/F

Answer 5

True

Question 6

____ indicates the location of components with respect to each other within the system.

Answer 6

Schematic Diagram

Question 7

The ____ Drawing line consists of alternating long and short lines

Answer 7

Center line

Question 8

The first step in sketching an aircraft Sheetmetal repair is the block in the views T/F

Answer 8

True

Question 9

Airworthniess Certificate is governed by 14 CFR ____

Answer 9

Part 21

Question 10

The certification of airmen other than flight crew members is governed by 14 CFR 65 T/F

Answer 10

True

Question 11

Instrument Repairs can be accomplished by _____

Answer 11

An FAA-Approved Instrument repair station

Question 12

AD compliance records are not required to be retained and transferred when the aircraft is sold T/F

Answer 12

False

Question 13

Prior to a certificated mechanic exercising the privileges of the cert, the administrator has to verify that the mechanic is able to do the work or has worked as a mechanic under the cert/rating for at least ____ months

Answer 13

6 months

Question 14

AC 43.13-1B is an example of approved data T/F

Answer 14

False

Question 15

Instrument range markings are governed by 14 CFR part _____

Answer 15

Part 23

Question 16

When Mooring an airctaft, ______ rope should be used

Answer 16

Nylon

Question 17

When aviation gas is mixed with jet fuel, it wil cause deposits to form on the turbine blade T/F

Answer 17

True

Question 18

Either standard grease or oxygren grease can be used on oxygen connections T/F

Answer 18

False

Question 19

The ideal measurements of parts on a drawing are called _____

Answer 19

Dimensions

Question 20

_____ Is the difference between the acceptable dimensions that a serviceable part may have

Answer 20

Tolerance

Question 21

What is the tolerance for a Hole drilled in aluminum where the interior dimensions are identified as .50” + .05” or - .01”

Answer 21

.06”

Question 22

Splicing of aircraft skin sheets is classified as a major repair T/F

Answer 22

True

Question 23

14 CFR part ______ states that the requirements for issuing mechanic certificaters and ratings and the general operating rules for individuals issued the certificates and ratings

Answer 23

65

Question 24

How long is an Airframe and Powerplant license valid for

Answer 24

Forever unless voluntarily surrendered, revoked or suspended

Question 25

The person approving/disapproving return to service is responsible for making the entry in maintenance records following an annual, 100 hr or progressive inspection T/F

Answer 25

True

Question 26

After anu change in permanent mailing address, the cert holder has ___ days to notify the FAA

Answer 26

30

Question 27

An AD for an aircraft that you're assigned to requires an alternation to the propeller. As a certified mechanic, you could perform and approve the work for return to service regardless of if its a major or minor alteration

Answer 27

False

Question 28

A certified and appropriately rated mechanic may perform a major repair or major alteration ____________________

Answer 28

But cannot approve the work for return to service

Question 29

A mech with a powerplant rating can approve a propeller for return to service following a 100 hr inspection T/F

Answer 29

True

Question 30

Primary responsibility for AD compliance falls on ____

Answer 30

The aircraft owner or operator

Question 31

when work is accomplished requiring the use of an FAA form 337, the form should be prepared by the person preforming or supervising the work T/F

Answer 31

True

Question 32

TSO stands for

Answer 32

Technical Standard Order

Question 33

A flashing white light from the control tower means ____

Answer 33

Return to your starting point

Question 34

When towing large aircraft, someone should be in the cockpit to operate the brakes T/F

Answer 34

True

Question 35

When accomplishing an engine run, the aircraft should be positioned into the wind for ___________

Answer 35

For engine cooling

Question 36

A hung start in a jet engine is typically caused by the starter cutting off too soon T/F

Answer 36

TrueWh

Question 37

When an induction fire occurs during reciprocating engine starting, your first action should be to ______

Answer 37

Continue cranking and start the engine if possible

Question 38

Is it acceptable to refuel an aircraft within 500' of radar operations T/F

Answer 38

False