General

Question 1

Is electrical power required for wing sweep operations?

Answer 1

No, they are hydraulically controlled

Question 2

Pressure reading for APU accumulators

Answer 2

3600 to 4250 psi

Question 3

Which component must be serviced prior to APU run what component must be checked

Answer 3

Service: ADG
Check: APU IDG

Question 4

What position must UHF 1 and UHF 2 switches be set to

Answer 4

Upper

Question 5

What position must the EMUX overtemp switch be set to?

Answer 5

On

Question 6

On FUEL MGT Panel, ensure CLG SCOOP is set to what position?

Answer 6

Auto

Question 7

What system is activated by the ENG BLEED AIR switches?

Answer 7

Bleed air Leak Detection System

Question 8

What are my limits for operating the parking brake switch

Answer 8

Don’t hold for more than 30 seconds. Allow for 5 minute cool down.

Question 9

What is load management 1 used for? How many APU’s are in use in this LM?

Answer 9

Refuel/Defuel. L APU only

Question 10

What is the nominal start time for starting the APU?

Answer 10

15 Seconds

Question 11

What percentage RPM will the APU RUN light illuminate?

Answer 11

95% RPM

Question 12

What shall be closed prior to APU operation

Answer 12

Lower engine bay doors

Question 13

What must personnel and equipment be clear off before applying hydraulic system pressure

Answer 13

Flight surfaces flight controls

Question 14

During an APU run, what must your hydraulic system pressure be between?

Answer 14

3900-4150 PSI

Question 15

What moves when you set the ENG INST TEST switch to HIGH?

Answer 15

APU Exhaust Doors

Question 16

How long is the SCDU powered up for when you press ENG INST TEST to HIGH? What LM must you be in momentarily?

Answer 16

2 minutes. LM 4

Question 17

To prevent APU oil from overheating, the APU shall not be operated without electrical power for how long?

Answer 17

5 minutes

Question 18

What must you do if you get an illuminated ENG switchlight on your Fire Warning & EXTGH panel when no engines are running? Why?

Answer 18

Shut down as if there were a fire. Engine comp loops may be detecting a fire

Question 19

What three things will occur immediately when a fire occurs in an APU compartment

Answer 19

1. APU will shut down
2. Light will illuminate
3. Aural tone will sound

Question 20

What load management do you have to monitor ACL and fuel inlet temperatures? How many PMCS are required to monitor?

Answer 20

LM 4 w/o External Cooling
ACL = 1 PMC
Fuel Inlet Temp = 2 PMC’s

Question 21

Minimum time to run APU before coupling?

Answer 21

30 seconds or 5 minutes if cold or not run in the last 4 hours

Question 22

How long should the ADG take to couple?

Answer 22

6 seconds

Question 23

How long should ADG couple below 30 degrees?

Answer 23

20 seconds

Question 24

What should I do if air is not coming out of one or more of my fuel cool scoops

Answer 24

Terminate APU run and troubleshoot

Question 25

ACL coolant supply temperature, during LM 4 (external power, no external cooling) operations should not exceed?

Answer 25

90 F

Question 26

Stop operations if fuel inlet temperatures exceed?

Answer 26

165 F

Question 27

What must you do if you turn on the battery switch and a fire switch light is depressed?

Answer 27

Reset switch between Engine switches

Question 28

What are the three modes for starting APU’s?

Answer 28

Alert, Normal, Manual

Question 29

How many fire bottles are there on the B-1 and where are they located?

Answer 29

There are 8 L OWF = 2 R OWF = 2 L Nacelle = 2 R Nacelle = 2

Question 30

What must be done prior to running APU’s if the Engine Instrument SCDU is removed?

Answer 30

Parking Brakes

Question 31

On Elec Panel, after BATT switch is set to AUTO/ON, what should my voltage read?

Answer 31

25 (+/-5) VDC

Question 32

What position on the FLT CONTR PWR panel must be the ALRER WG SWP switch be in prior to coupling & decoupling APU’s?

Answer 32

Hold

Question 33

What is the power source for the FIRE WARNING & EXTINGUISHING panel and the OWF/FIRE DETR panel?

Answer 33

Aft & fwd DC BATTERY

Question 34

How long can you run with hot lights?

Answer 34

4 minutes

Question 35

What are your main fuel tank limitations?

Answer 35

6100 - 10500 lbs per tank

Question 36

What should the main fuel tank valves be set to?

Answer 36

Closed

Question 37

What do you do if you get a MLG aural unsafe tone?

Answer 37

Shut down

Question 38

At what oil temperatures will the ECA shut down the APU?

Answer 38

Over 290 F

Question 39

The CRSVR Air switch should be in what position?

Answer 39

OFF

Question 40

Prior to APU start, what position do you set the TRANS pumps to on the Fuel Management Panel?

Answer 40

OFF