Gouge

Question 1

Under the prompt pay act, how long does ALC have to pay for items?

Answer 1

The Prompt Payment Act requires that invoices be paid within 30 days of receipt of materiel, or interest must be paid to vendor.

PG 85-00-10 pg. 6-7

Question 2

How many characters for SCHR?

Answer 2

600 characters in the comments section.

PG 85-00-110 pg 3-13

Question 3

What do you use to clean a hydraulic patch kit?

Answer 3

MIL-PRF-680 is the only solvent authorized for performing the contamination analysis with kit P/N 57L414.

NAVAIR 01-1A-17 pg 005 00 page 4

Question 4

When do you notify the CO for level of FSII?

What is FSII?

Answer 4

If the FSII level in bulk storage drops below 0.07% by volume, the airstation CO must be notified.

PG-85-00-170 PG 6-7

Question 5

Which color paint is not authorized on women’s fingernails?

Answer 5

Blue paint is not authorized

COMDINST M1020.61 PG2-14

Question 6

Who authorizes alternate uniform for NFFD?

What is NFFD?

Answer 6

Commands have discretion after consulting with competent medical authority regarding alternate uniforms (e.g. ODU vs Trop Blue), to include soft sole shoes or suitable civilian clothing.

COMDINST M1020.61 PG 1-5

Not Fit for Full Duty

Question 7

Who authorizes shave chits?

Answer 7

Commanding Officers or OIC will grant permanent shaving waivers for personnel who have received a confirmed diagnosis of Pseudoflliculitis Barbae (PFB) by a medical doctor providing health care for unit personnel.

COMDINST M1020.61 PG 2-13

Question 8

How many safety steps must you know verbatim to handle a firearm?

Answer 8

IAW the Ordinance Manual, COMDINST M8000.2, everone who handles firearms SHALL memorize the following FOUR firearm safety rules and should recite them verbatim.

Recruit Master Training Packet PG 207

Question 9

In a windshield, what controls heat?

Answer 9

Whether resistance wires or a laminated conductive film is used, aircraft window heat systems have transformers to supply power and feedback mechanisms, such as thermistors, to provide a window heat control unit with information used to keep operating temperatures within acceptable limits.

FAA-H-8083-31-V2 PG 15-29

Question 10

What do you do when you see a fire?

Answer 10

Remember the acronym ACE:
A: Give or sound Alarm
C: Contain the fire
E: Extinguish and/or escape.

Recruit Training Master Packet PG 193

Question 11

How is a gas turbine engine rated for horsepower?

Answer 11

The gas turbine engine is rated in thrust horsepower.

FAA-11-8083-32-V1 PG 1-2

Question 12

What percentage of power does the prop take from the compressor?

Answer 12

Approximately 80-85% of the energy developed by the gas turbine engine is used to drive the propeller.

FAA-11-8083-32-V1 PG 1-37

Question 13

What are the benefits of the axial compressor?

Answer 13

1. High Peak Efficiencies
2. Smal frontal area for given airflow
3. Straight-through flow, allowing high ram efficiency
4. Increased pressure rise by increasing stages with negligible losses.

FAA-H-8083-32-V1 PG1-43

Question 14

What is the law for calculating voltage drop?

Answer 14

A law of basic importance to the analysis of an electrical circuit is Kirchhoff’s voltage law, which states that the alegebraic sum of all voltages around a closed path is zero. OR The sum of all the voltage drops equals the total source voltage.

FAA-H-8083-30 PG 10-36

Question 15

Who can permanently delete a maintenance discrepancy?

Answer 15

The deleted discrepancy can be restored by a Maintenance Supervisor. A Maintenance Release Authority can restore and/or permanently delete a discrepancy.

PG-85-00-10 PG 2-24

Question 16

Who must have a plan for Hazardous material?

Answer 16

All CG workplaces using or producing hazardous materials (HAZMAT) must have written HAZCOM plan.

COMDINST M5100.47B PG 11-1

Question 17

Who can authorize a discrepancy open for 30 days?

Answer 17

With the exception of deployed assets, no deferred discrepancies shall remain open for a period longer than 30 days without the approval of the unit Engineering Officer or their designated representative.

PG-85-00-110-A PG 5-5

Question 18

What is the MPC to relocate MSR?

What is MSR?

Answer 18

MPC 051015.1 MSR relocation

ATIP

Question 19

How many aircraft dispositions are there?

Answer 19

There are five aircraft dispositions.
-Service
-Spare
-Support
-Maintenance
-Storage

PG-85-00-160-A PG 2-1

Question 20

What classification of fuel leak for an aux tank on a HH-60 of 4 drops per minute?

Answer 20

Using a 6 minute leak check,
- Class A: Slow seep 0-1/4 inch
- Class B: Seep greater than 1/4 to 3/4 inch
- Class C: Heavy seep greater than 3/4 to 8 inch OR less than 4 drips per minute.
- Class D: Running Leak, greater than 8 inches or 4 drops per minute

TO 1-1-3 PG 4-3

Question 21

What is the hazard to storing a fuel cell close to electrical?

Answer 21

Electrical equipment produce Ozone, which will cause rubber to crack.

NAVAIR 01-1A-35 010 00 PG 12

Question 22

Wheel alignment to the longitudinal axis:

Answer 22

• Tow in: Converge on the longitudinal axis.
• Tow out: Veer away from the longitudinal axis.
• Aligned: parallel to the longitudinal axis.

FAA-H-8083-31-V2 PG 13-15

Question 23

What is wheel camber?

Answer 23

Camber is the alignment of a main wheel in the vertical plain.
- Positive: Top of the wheel tilts out from the vehicle.
- Negative: Top of the wheel tilts in towards the vehicle.

FAA-H-8083-31-V2 PG 13-15

Question 24

What is it called when a helo has a tendency to go in direction of the tail rotor?

Answer 24

During hovering flight, a single main rotor helicopter tends to drift or move in the direction of the the tail rotor thrust. This drifting tendency is called translating tendency.

FAA-H-8083-31-V1 PG 2-22

Question 25

What do ailerons do for movement of flight?

Answer 25

Ailerons are the primary flight control surfaces that move the aircraft about the **longitudinal axis**. | FAA-H-8083-31-V1 PG 1-26

Question 26

After stop drilling, what increment do you step up to?

Answer 26

If the crack extends beyond the stop hole, enlarge the hole by **1/16"** diametrical increments until the crack indication is removed. | 1-1A-1 PG 3-14

Question 27

What are the EAL contingency operations?

Answer 27

These procedures were designed specifically to ensure flight safety through the availability of previously entered records and the continued documentation of flight and maintenance operations. **MPC 00EAL.0** | PG-85-00-110-A PG 5-1

Question 28

How long do you retain EAL paper copies?

Answer 28

Paper forms will be retained at the unit for **90 days** after entry into EAL and then may be destroyed. | PG-85-00-110-A PG 5-2

Question 29

How long for a TCTO to become an SCTO?

Answer 29

Any TCTO requiring compliance beyond **180 Days** shall be considered an SCTO. | PG-85-00-40 PG 3-1

Question 30

What percent of a SCTO will be procured before being sent out to units?

Answer 30

Sufficient quantities (**normally 10 to 30 percent**) of the kits should be built in advance of the SCTO release. | PG-85-00-40 PG 3-1

Question 31

How do you tell if hydraulic fluid has been contaminated by oxidation?

Answer 31

Oxidation- **Dark Fluid**, not clear. | NAVAIR 01-1A-17 PG 006 00 page 6

Question 32

Who is in charge of spill response for fuel?

Answer 32

**Commanding Officers** shall ensure a functional spill prevention control and countermeasure (SPCC) is in place. | PG-85-00-170 PG 3-1

Question 33

Who does a CG-22 go to after the EO?

Answer 33

Originator, QA, EO, **PRIME UNIT**, ALC Tech Services. | PG-85-00-20-A PG 2-2 through 2-5

Question 34

What level can you fly at without pressurization and with oxygen?

Answer 34

Aircraft with oxygen equipment available but unable to pressurize will not exceed **FL 180** unless a comprehensive breifing by competent aviation medical authority is obtained immediately prior to the flight. | COMDINST M 3710.1 PG 7-9

Question 35

What altitude level should aircraft be able to maintain?

Answer 35

It must be capable of maintaining a cabin pressure altitude of approximately **8,000 ft** or lower regardless of the cruising altitude of the aircraft. | FAA-H-8083-31-V2 PG 16-23

Question 36

How do you calculate Bend allowance? | LOCATE ANSWER TO QUESTION

Answer 36

Utilize bend radius formula | 1-1A-1 PG 8-3

Question 37

What is the overlap for scarf ratio of 30:1?

Answer 37

Multiply the repair ply thickness by the scarf ratio (0.055 x 30 = 0.165") | 1-1-690 PG B-5

Question 38

What is the meaning of the colored tape on an aircraft tire?

Answer 38

Color-coded tape is used by supply for stock control identification, and is applied by the manufacturer on all aircraft tires. The color and year found on the tape represent the** year the tire was originally manufactured (not the retred date)** | NAVAIR 04-10-506 PG 2-3

Question 39

What is the maximum men's hair bulk?

Answer 39

The bulk of hair must not be more than **1-1/2** inches from scalp. | COMDINST 1020.6I PG 2-9

Question 40

According to the UCMJ, what is solicitation?

Answer 40

Any person subject to this chapter who solicits or advises another or other to **desert** in violation of section 885 of this article (Article 85) or **mutiny** in violation of section 894 of this title (Article 94) shall, if the offense solicited or advised is attempted or committed, be punished with the punishment provided for the commission of the offense, but, if the offense solicited or advised is not committed or attempted, shall be punished as a court-martial may direct. | UCMJ 2012 PG IV-7

Question 41

What is the 4th tab in CGBI?

Answer 41

The four views are: - Enterprise - Unit: People, Training, Equipment, and Infastructure - Personal: Compliance and Skills - **Cubes / Reports** | CGBI Basic Training Guide p. 8

Question 42

What do you do in EAL after receiving an A/C part for a PP discrepancy?

Answer 42

Upon receipt of the part, an additional comment stating "**Parts received and awaiting installation**" shall be added to the PP discrepancy. | PG-85-00-110 PG 5-5

Question 43

At what PSI is an oxygen bottle considered empty?

Answer 43

Oxygen cylinders are considered empty when the pressure drops below **50 psi**. | FAA-H-8083-31-V2 PG 16-7

Question 44

What test is used to determine the serviceability of high-pressure oxygen cylinders?

Answer 44

**Hydrostatic Test**: The cylinders are filled with water and pressurized to **5/3** of their working pressure. | FAA-H-8083-31-V2 G-19

Question 45

What is the maximum gap when checking a Teflon spiral backup ring?

Answer 45

Make sure the coils do not seperate more than **1/4 inch** when unrestrained. | FAA-H-8083-31-V2 PG 12-37

Question 46

How do you know if a flangeless bushing is installed properly?

Answer 46

If a bushing doesn't have a flange, it should be installed so that the top (i.e. exposed) face of the bushing is **flush to 0.002" below** the surface of the boss material in which the bushing is installed. | TO 1-1A-1 PG 3-13

Question 47

What areas of a cable are considered "critical fatigue areas"?

Answer 47

Anywhere the cable runs over, under or around a pulley, sleeve, or fairlead; or any section where the cable is flexed, rubbed, or within **1 foot** of a swaged-on fitting. | FAA-H-8083-31-V1 PG 2-44

Question 48

How much delfection is authorized in a cable fairlead?

Answer 48

Fairleads should never deflect the alignment of a cable more that **3 degrees** from a straight line. | FAA-H-8083-31-V1 PG 2-45

Question 49

What are the authorized ribbon configurations on the Winter Dress Blue?

Answer 49

**Ribbons must be worn in precedence going from wearer's left (outboard) to right (inboard)** 1. All Ribbons 2. Up to nine ribbons of the wearer's choice 3. The three highest precedence ribbons. NOTE: Those possessing three or more must wear a minimum of three ribbons. | COMDINST M1020.6I PG 4-43

Question 50

Where shall the trousers fall in relation to the shoe on the Service Dress Blue uniform?

Answer 50

1. Coat fits easily over chest and shoulders. 2. Sleeves fall 1 inch below the bottom of the wrist bone, covering the shirt sleeve. 3. Bottom edge of the coat extends below the crotch (approximately to the tip of the thumb). 4. Shirt collar shows at least 1/4 inch to 1/2 inch above the coat collar at the center back of the coat. 5. Trousers have no break in the front. 6. The bottom of the front crease of the trousers will reach the top of the instep and be cut on a diagonal. 7. Back edge of the trousers will fall approximately midway between the top of the heel and the top of the standard shoe in the back. | COMDINST M1020.6I PG 3-31

Question 51

Who is responsible for the recovery and salvage of Coast Guard aircraft?

Answer 51

Recovery and salvage of Coast Guard aircraft is the responsibility of the **Commanding Officer** of the unit to which the aircraft is permanently assigned. | COMDINST M1320.1G PG 10-1

Question 52

How many days must you be exposed to HAZMAT in order to enroll in OMSEP?

Answer 52

Where standards do not exist, personnel who meet the requirement of being exposed above 50% of the OEL for **over 30 days per calendar year** must be enrolled in the medical surveillance program. | COMDINST M5100.47 PG 26-4

Question 53

How much obligated service is required upon completion of a 2 year college program?

Answer 53

Military members are obligated to serve in the Coast Guard three months for each month of instruction for the first 12 months, and one month for each month thereafter. **48 months** | COMDTINST M1500.10C PG 10-4

Question 54

What is Pascal's Law of hydraulics?

Answer 54

Pressure of a fluid acts equally in all directions. This pressure acts at right angles to the containing surface. | AFTO 42B2-1-12 and NAVAIR 01-1A-17

Question 55

What is the minimum diameter rivet used in structural repairs?

Answer 55

Rivets that have a diameter smaller than **3/32 inch** will not be used for any structural parts, control parts, or similar aircraft parts. | TO 1-1A-1 PG 3-4

Question 56

How many days for a new member to get acclimated to their environment?

Answer 56

Acclimatization varis between individuals, some taking longer than others to acclimatize. A minimum period of **seven days** is required for acclimatization of unseasoned Coast Guard personnel. | COMDTINST M5100.47 PG 8-1

Question 57

How often does a rescue swimmer need to fly with the stan team?

Answer 57

All rescue swimmers are required to be evaluated by an ATC Mobile STAN swimmer once every **4 years**. | COMDINST M3710.4C PG 3-3

Question 58

What is the minimum wait time for a non-rate before submitting a request to attend "A" school?

Answer 58

Non-rates must wait **4 months** after reporting to their first unit, unless their chosen rating is deemed critcal under CG Standards. | Recruit Training Master Packet PG 48

Question 59

In ORM, which model involves environment, personnel and equipment?

Answer 59

Looking at each element of the **"PEACE" (Planning, Event complexity, Asset Selection, Communications, and Environmental conditions)** will ensure effective hazard identification in each of three main categories: Equipment, Environment, and Personnel. | COMDINST 3500.3 ENCL 1 PG 3

Question 60

What is the report of Offense and Disposition?

Answer 60

CG-4910 | COMDTINST M5810.1E PG 1-7

Question 61

What is needed to lookup E-Resume command endorsement?

Answer 61

EMPLID | DA Self Service eResume Guide Step 18

Question 62

What is needed to edit a member's training record?

Answer 62

Military membes, active and reserve, shall inform Commander, CG Personnel Service Center (PSC) and Commandant (CG-1B1) by 1 August of each year of recently acquired training or education on the Record of Professional Development, form **CG-4082,** for inclusion into Direct Access. | COMDTINST M1500.10C PG 4-2

Question 63

How long is the Rescue Swimmer training record kept?

Answer 63

All Rescue Swimmer training shall be documented, with a date of completion, on a locally generated Helicopter Rescue Swimmer Training Record form as per the example in Appendix F. This Record shall be maintained for a minimum of **18 months**. | COMDTINST M3710.4C PG 3-12

Question 64

How often must the RPM coordinate with unit safety to complete a self-evaluation on the unit RPP?

Answer 64

Annually | COMDINST M5100.47B PG 9-8

Question 65

During Rockwell hardness testing, what are two factors that must be considered to avoid distortion of the metal?

Answer 65

Material Thickness and Edge Distance | AC43_13-1B FAA ACCEPTABLE METHODS, TECHNIQUES, AND PRACTICES PG 4-5

Question 66

What is the area called where the two dissimilar metals join on thermocouples?

Answer 66

A loop consisting of two kinds of wire, joined at the **hot, or measuring,** junction and at the cold junction in the instrument. | FAA-H-8083-31-V2 PG G-36

Question 67

What continuous loop system has two wires imbedded in an inconel tube, filled with a thermistor core material?

Answer 67

Kidde System | FAA-H-8083-31-V2 PG 17-4

Question 68

What percentage of torque is utilized to overcome the friction on working surfaces?

Answer 68

About **50%** of the torque is absorbed in overcoming friction on the working faces of the bolt and nut, while 40% is taken up by thread friction, leaving only 10% to apply bolt tension (preload). | 1-1A-8 PG 5-1

Question 69

At what percentages should prevailing torque be ignored, or added to, recommended torque?

Answer 69

If the prevailing torque is **1/3 or more** of the recommended torque, it should be added to the recommended torque. | TO 1-1A-8 PG 5-1

Question 70

What system is used to order items and accounting / software used for procurement and issuing funds? (CMPLUS/FEDLOG)

Answer 70

Finance and Procurement Desktop System (FPD) | COMDTINST M4200.13H PG 1-7

Question 71

What is the MILSTRIP code for routing to ALC?

Answer 71

The routing identifer code is **ZQC**. | COMDTINST M4400.19B PG D-80

Question 72

What is entered on a SCHR entry when the date is unknown?

Answer 72

Enter date manufactured. If date is unknown, enter 01/01/1961. | PG 85-00-10-A PG 3-11

Question 73

What is entered if there is a discrepancy with no ATA chapter?

Answer 73

Use **Chapter 12** for discrepancies that do not have an ATA chapter. | PG-85-00-110-A PG 5-23

Question 74

What organization authorizes the use of metals on Aircraft?

Answer 74

Society of Automotive Engineers (SAE) American Iron and Steel Institute (AISI) | FAA-H-8083-30 PG 5-2

Question 75

When shall the memorandum be sent out to Tri-swap assets?

Answer 75

In no case shall the memorandum be submitted later than **30 calendar days** after aircraft acceptance. | PG-85-00-110 PG 4-9

Question 76

What category PQDR will JDRS automatically send a message?

Answer 76

JDRS will automatically generate and distribute a message in the CG message system to applicable, preaasigned units when a **Category 1** PQDR is submitted. | PG-85-00-1320 PG 2-1

Question 77

How long to respond to an URGENT CG-22?

Answer 77

The available priority codes define the number of days from receipt of the CG-22 at TPS Manager/MPC Final level to distribution to the units: **URGENT - 7 days**, NonRoutine - 14 Days, and Routine - 90 days. | PG-85-00-20-A PG 1-1

Question 78

How many types of changes are there for CG-22s against MPCs?

Answer 78

There are three change types: Procedural vs. Nonprocedural, Interval, and COMDT change. MPC only has **TWO** types. | PG-85-00-20-A PG 2-1

Question 79

A fastener can be inserted at a maximum of how many degrees from flush?

Answer 79

Unless otherwise specified on the engineering drawing, holes should be perpendicular to the surface upon which the fastener head will seat **within +/- 3 degrees . ** | TO 1-1A-1 PG C-3

Question 80

How much overshoot is authorized during fueling?

Answer 80

Overshoot not to exceed **5%** of actual flow rate from the time the deadman control is released until the time flow stops completely. | PG 85-00-170-A PG 4-6

Question 81

How much additional training is required to keep an EMT certification?

Answer 81

To further develop the emergency medical skill level and meet the **48 hours** of continuing education required by the National Registry of EMT, it is highly encouraged that operational and nonoperational rescue swimmers acquire local Emergency Medical Service training in addition to the EMT classroom and practical training listed in this chapter. All CG EMTs must complete a total of **72 hours** of continuing education to recertify with the NREMT, prior to the expiration of their current NREMT card. | COMDTINST M3710.4C PG 3-7, 3-10

Question 82

If you submit a CG-22 for PG 85-00-110, who is the prime unit?

Answer 82

**Airworthiness Sustainment Branch** Updated manual states **ASB Chief**. | PG 85-00-20 Enclosure 2

Question 83

Who authorizes avionics changes that don't affect form, fit, or function at PDM?

Answer 83

**The Commanding Officer, ALC**, may approve depot level changes that do not affect the form, fit, or function of the equipment when necessary during the depot repair cycle. | COMDTINST M13020.1G PG 8-3

Question 84

Who authorizes outside maintenance providers to make structural changes at PDM?

Answer 84

The respective **ALC Product Line Manager** will develop, advise, coorinate, and direct the repair plan (e.g. field team, depot fabrication of replacement parts, UDLM at ALC or other DOD/commerical depot activity, early PDM induction). | PG 85-00-110 PG 7-1