Hazards Flashcards
(30 cards)
DOGGING WORK INCLUDES THE RESPONSIBILITY OF WHAT TASKS?
- SELECTING SLING AND SLINGING TECHNIQUES
- ASSESSING LOADS
- INSPECTING LIFTING GEAR
- DIRECTING THE CRANE OPERATOR
AT WHAT POINT DOES A PERSON SILING A LOAD NEED A DOGGING LICENCE
- SELECTING SLING AND SLINGING TECHNIQUES
- ASSESSING LOADS
- INSPECTING LIFTING GEAR
- DIRECTING THE CRANE OPERATOR
LIST 3 PEOPLE YOU SHOULD TALK ABOUT SITE HAZARDS BEFORE YOU START WORK
- OTHER WORKERS
- SUPERVISORS
- ENGINEERS
WHY IS IT IMPORTANT TO TALK TO THESE PEOPLE BEFORE STARTING WORK
- KNOW THE HAZARD
2. FOLLOW WORK PLACE POLICIES AND PROCEDURES
LIST 10 HAZARDS YOU MIGHT FIND IN THE WORK PLACE
- POOR LIGHTING
- UNDERGROUND SERVICES
- POTENTIAL NON-WEIGHT BEARING SERVICES
- PEDESTRIANS
- VEHICLES
- TREES
- POWERLINES
- WEATHER - LIGHTENING AND WIND
- BUILDINGS
- WORKERS / DANGEROUS MATERIALS
OTHER THAN IDENTIFIED HAZARDS, LIST 5 THINGS YOU MUST CONSIDER
- SIZE OF LOAD
- COMMUNICATION
- ACCESS AND EGRESS
- LOCATION OF LOAD
- PERMITS
LIST THE HIERARCHY OF CONTROLS FROM THE MOST EFFECTIVE TO THE LEAST
- ELIMINATION C
- SUBSITUTIONS
- ISOLATION
- ENGINEERING
- ADMINISTRATIVE CONTROLS
- PPE
WHEN SHOULD YOU CHECK IF YOUR PPE IS SAFE TO USE
BEFORE USE
WHEN SHOULD YOU CHECK IF YOUR PPE IS SAFE TO USE
WHEN SHOULD RISK CONTROL MEASURES BE PUT IN PLACE
- BEFORE STARTING WORK
3. WHEN IDENTIFIED
LIST 4 ITEMS OF PPE A DOGMAN SHOULD WEAR
- HARD HAT
- SAFETY SHOES
- SAFETY GLOVES
- HIGH VISIBILITY CLOTHING
WHEN SHOULD EXCESS MATERIAL BE REMOVED FORM THE WORK AREA
AS SOON AS POSSIBLE
WJAT ARE THE 3 ZONE DISTANCE AND CORRESPONDING VOLTAGES FOR WORKING NEAR POWER LINES IN NSW
- 3 M - 132 KV
- 6 M - 330 KV
- 8 M - 330 KV AND ABOVE
IF YOU NEED TO WORK CLOSER THAN THESE MINIMUM DISTANCE HOW CAN THIS BE DONE
- HAVE THE POWER TURNED OFF
- EXEMPTION / PERMIT
- SAFETY OBSERVER
HOW CAN YOU DETERMINE THE VOLTAGE OF OVERHEAD POWERLINES
- SIGNANE
2. CALL POWER COMPANY
WHAT IS USED TO INDICATE THE PRESENCE OF OVERHEAD POWERLINES
TIGER TAILS
WHAT SIZE SHOULD A TAGLINE BE
16 MM
WHAT MATERIAL SHOULD A TAGLINE BE MADE OF
NON-CONDUCTIVE ROPE
WHY IS IT CONSIDERED UNSAFE TO RAISE OR LOWER THE BOOM OVER PEOPLE
RISK OF SERIOUS INJURY OR DEATH
HOW DO YOU DETERMINE IF A CCLP CAN TAKE THE WEIGHT OF THE LOAD
- CHECK SAFE WORKING LOAD ON CCLP
2. CALL MANUFACTURER
WHAT NEEDS TO BE CONSIDERED WHEN PLACING A LOAD ON A CONCRETE FLOOR? WHERE WOULD YOU GET THE REQUIRED INFORMATION FOR THIS TASK.
- SAFE WORKING LOAD OF FLOOR
2. ENGINEER
WHAT IS THE HAZARD AND HOW WOULD YOU CONTROL IT FOR PEOPLE WORKING NEAR THE CHASSIS OR OUTRIGGER OF A MOBILE SLEWING CRANE
- BEING STUCK OR CRUSHED
2. EXCLUSION ZONE
WHAT NEEDS TO BE PROVIDED IN DARK OR POORLY LIT AREAS
ADEQUATE LIGHTING ACROSS ENTIRE WORK AREA
LIST 2 HAZARDS THAT CAN RESULT FROM WORKING WHEN ITS WINDY
- LOAD SWING/SPIN
3. CRANE INSTBAILITY
