IEM

Question 1

Seawater System- How many sea water service pumps are there on board?

Question 2

What are the parameters for SWSP?

Question 3

Generator sea water cooling pump located?

Question 4

Where are the FM back up cooling controller located?

Question 5

Where are the Generator strainers located at?

Question 6

What do we start/stop SWSP IAW?

Question 7

Fuel System- Purpose of the Fuel Oil system?

Question 8

What are the pumps rated at for slow and fast speed?

Question 9

Fuel head tank purpose? How many do we have?

Question 10

What components have fuel throughout the space in them?

Question 11

Lube Oil System- Purpose of the Lube oil system?

Question 12

What are the lube oil logics?

Question 13

What kind of lube oil do we have on board?

Question 14

What kind of oil is for the Generators?

Question 15

What is important to note for adding oil to generators?

Question 16

Where do you check the oil for generators? And what do you need to check it with?

Question 17

How many sumps do we have for the generators and what are their capacity?

Question 18

23699 stands for what?

Question 19

What kind of oil is going thru the Lube Oil cooler?

Question 20

What cools the L/O Cooler?

Question 21

What type of cooler is it?

Question 22

How many lube oil pumps does the generator have?

Question 23

What kind of generator do we have onboard COLE?

Question 24

What are the parameters of the generator?

Question 25

What kind of compressor does the Generator have?

Question 26

What kind of combustor does the Generator have?

Question 27

What makes 3 Generator different from the other generators when starting and securing?

Question 28

What do you enter the GTG IAW?

Question 29

What do you need to do before entering the enclosure?

Question 30

What are you inspecting for visuals on the generators?

Question 30

Where do you record the samples at?

Question 31

What samples do you take on the midnight watch?

Question 32

What do you do if the Line Shaft bearing is low when samples are required?

Question 33

Where are the Storage tanks? How many do we have?

Question 34

Where are the Settling tanks? How many do we have?

Question 35

What do you monitor in Shaft Alley?

Question 36

What alignment do you align Stern Tube IAW?

Question 37

Where are the Line Shaft Bearing located?

Question 38

Where are the Thrust Bearing located?

Question 39

Where can you get oil in shaft alley for the line shaft bearings?

Question 40

What do we maintain L/O temperature at IAW EOSS?

Question 41

Where is the location to remotely and locally operate F/O system pressure?

Question 42

How do you adjust F/O pressure manually?

Question 43

Explain what you need to do before starting lube oil?

Question 44

Explain what you need to do before starting fuel?

Question 45

What is quick heat?

Question 46

When aligning lube oil what needs to be secured?

Question 47

Before starting CRP what are you going to do?

Question 48

If we lose shore power what are you going to do?

Question 49

How do you PROPERLY charge the expansion tank?

Answer 49

- Secure exp tank isolation valve, charge the tank, re-open the isolation valve IAW ACCW.

Question 49

What is aligning and securing an A/C IAW? Describe how it is done.

Answer 49

-ACCW -These need to be mentioned: align seawater, align C/W and start pump, ensure oil pressure is above 32 psi (if it is not the oil pump needs to be switched to manual to bring up pressure)

Question 50

How do you cycle a seawater strainer? Why would you do it?

Answer 50

- open the drain valve, cycle in the indicated direction. -when the differential pressure is high.

Question 51

What does the green light on the reefer indicate?

Answer 51

-OFF: the reefer is cycling. -ON: The reefer shut down. and the oil heater is on. (If it is the online reefer, it must be restarted.)

Question 52

How do you align the RODM?

Answer 52

-IAW RODM, they need to mention where the breaker is (L/L in the port/aft corner of aux 1)

Question 53

What is LOP EA014 utilized for? Where is valve CPW-V-40?

Answer 53

-Shifting from ship to shore, or shore to ship. ( running the potable water system off of the tanks and pumps, or taking the pressure straight from the shore water.) -L/L AUX 1 behind the spy skid.

Question 54

What do you test potable water IAW? What are the parameters the bromine needs to be?

Answer 54

-LOP EA 003. - above 0.2 PPM

Question 55

Where are the potable water heaters?

Answer 55

-MER 1

Question 56

What are you looking for while standing by to start pumps? What do you do if there is not good pressure or erratic pressure?

Answer 56

- rotation in the correct direction, leaks, vibrations, loud noises - vent the pump

Question 57

What is LOP EA 013? When do you do this?

Answer 57

-HP to LP air cross connect -When ordered to during loss of LP air.

Question 58

What do you aling and start a potable water pump IAW?

Answer 58

-PWPM