Lesson 3

Question 1

This command will insert a point marker in your drawing at a position
which you pick or at any coordinate location which you enter in the Command
window

Answer 1

Point (PO)

Question 2

__________Creates a straight_______. It is used to draw _____ continuously. Each
segment is a _________ that can be edited separately.

Answer 2

Line (L), line segment, lines, line object

Question 3

Continues a line from the endpoint of the most recently drawn line.

Answer 3

CONTINUE

Question 4

End the line segment at the beginning of the first line segment, which forms a
closed loop of line segment

Answer 4

CLOSE

Question 5

Erases the most recent segment of a line sequence.

Answer 5

UNDO

Question 6

This command creates a line of infinite length which passes
through two picked points.

Answer 6

Construction line (XLINE)/(XL)

Question 7

They are very useful for creating construction
frameworks or grids.

Answer 7

Construction Lines

Question 8

They are not normally used as objects in finished
drawings.

Answer 8

Construction Lines

Question 9

Construction line options

Answer 9

• Hor
• Ver
• Ang
• Bisect
• Offset

Question 10

Creates a horizontal construction line.

Answer 10

Hor

Question 11

Creates a horizontal construction line.

Answer 11

Hor

Question 12

Creates a vertical construction line.

Answer 12

Ver

Question 13

Creates a vertical construction line.

Answer 13

Ver

Question 14

Creates a construction line at a specified angle.

Answer 14

Ang

Question 15

Create a construction line that bisects an angle defined by 3 points.

Answer 15

Bisect

Question 16

Creates a construction line that is offset from an existing line by a specified
distance.

Answer 16

Offset

Question 17

The segments of this command are connected, when using it, all line segments are one object

Answer 17

Polyline (Pline)/(PL)

Question 18

A ________ of sides ranging from 3 to any number can be drawn using ___________

Answer 18

Polygon, Polygon Command

Question 19

Defines the center of the polygon.

Answer 19

Centre of Polygon

Question 20

Specifies the radius of a circle on which all vertices of the polygon
line.

Answer 20

Inscribed in Circle

Question 21

Specifies the distance from the center of the polygon to the
midpoints of the edges of the polygons

Answer 21

Circumscribe about Circle

Question 22

Defines a polygon by specifying the endpoints of the first edge.

Answer 22

Edge

Question 23

Specifying the radius with your pointing device determines the _____ and ________ of the
polygon.

Answer 23

Rotation, Size

Question 24

Specifying the radius with a value draws the _________ of the polygon at the
current ________.

Answer 24

Bottom Edge, Current snap rotation angle

Question 25

This command is used to draw an arc accurately.

Answer 25

Arc

Question 26

To create an arc, a combination of _________, ________, ________, ______, ______, _________, and ________ can be specified.

Answer 26

-Centre -Endpoint -Start point -Radius -Angle -Chord length -Direction values

Question 27

In what directions are arcs drawn by default?

Answer 27

Counter clockwise

Question 28

Draws an arc

Answer 28

Start point

Question 29

Defines the radius of the circle.

Answer 29

Center Point and Radius

Question 30

Defines the diameter of the circle.

Answer 30

Center point and Diameter

Question 31

Draws a circle based on three points on circumference.

Answer 31

3P (Three Points)

Question 32

Draws a circle based on two endpoints of the diameter.

Answer 32

2P (Two Points)

Question 33

Possible ways of drawing the circle

Answer 33

-Center point and Radius -Center point and Diameter - 3P (Three Points) - 2P (Two Points)

Question 34

Default way of drawing a Circle

Answer 34

Center point and radius

Question 35

Ellipse command

Answer 35

Ellipse (E)

Question 36

The default option in drawing an ellipse is to pick the ____________ and then a __________ to define the _________ of the ellipse.

Answer 36

two end points of an axis, third point, eccentricity

Question 37

A special type of polyline which is made up of arc segments

Answer 37

Donut

Question 38

What are the two properties of a Donut

Answer 38

It has Width It is Closed

Question 39

How is the width of a Donut set?

Answer 39

Specifying inside and outside diameters

Question 40

This command is used to fill up the area using a suitable pattern.

Answer 40

Hatch (H)

Question 41

The hatching will be carried out inside a _________.

Answer 41

Closed defined area

Question 42

_______, _________ and ______ can be inserted as required on an engineering drawing.

Answer 42

Words, messages, numbers

Question 43

The ________ is used extensively for non-graphical input such as text.

Answer 43

Alphanumeric keyboard

Question 44

Attributes associated with text.

Answer 44

text style height text angle aspect ratio colour

Question 45

This command creates a rectangular polyline.

Answer 45

Rectang (R)

Question 46

Parameters of a rectangle

Answer 46

Length Width Rotation

Question 47

Types of corners

Answer 47

Fillet Chamfer Square