leveling and installation

Question 1

primary equipment means

Answer 1

first equipment set in place

Question 2

main support machine rests is

Answer 2

foundation

Question 3

point of permant character established by the surveyor used as a reference point

Answer 3

bench mark

Question 4

electric motors combustion engines known as

Answer 4

prime movers

Question 5

it is critical to inspect equipment for damage on delivery

Answer 5

True

Question 6

care of equipment prior to installation

Answer 6

filling bearing housing with lubricant, remove foreign materials, rotate shafts, all of the above

Question 7

most important consideration lifting equipment is that its balanced?

Answer 7

True

Question 8

a complete equipment installation

Answer 8

all of the above/ levelling aligment test running installation

Question 9

prior to installing specified lubricant

Answer 9

remove the flushing oil from equipment

Question 10

prior to powering up new equipment

Answer 10

install all equipment guards and platforms

Question 11

record of installation should be kept for each piece of equipment

Answer 11

true

Question 12

prior to installation of prime mover bearing clearances should be checked

Answer 12

true

Question 13

mounting method for machinery must

Answer 13

support, absorb vibrator, secure machine/ all the above

Question 14

equipment that is mounted directly on concrete floors

Answer 14

requires special mounting pads

Question 15

when ever mounting equipment on structural steel use a

Answer 15

base plate

Question 16

when using adjustable machinery mount it is important to do

Answer 16

cleaned and greased so it doesnt jam

Question 17

a unit that prevents machine vibrations

Answer 17

vibration isolator.

Question 18

vibration isolator may be

Answer 18

absorbent pad or spring mounted

Question 19

essential foundations of machine

Answer 19

true

Question 20

machine sole plates installed

Answer 20

for shimming

Question 21

when using L shaped anchor bolts, the length of the bend should be

Answer 21

4 times the diameter

Question 22

straight anchor bolts without deformed ends

Answer 22

installed 25 times their diameter

Question 23

purpose of a pipe of tube anchor bolt

Answer 23

to provide movement in the anchor bolt

Question 24

boxed anchor bolts designed for access to replace

Answer 24

true

Question 25

packing waste may be used from the anchor sleeve

Answer 25

true

Question 26

where anchor bolts need to be installed in exsisting concrete

Answer 26

hole is drilled and mechanical advantage anchors used

Question 27

anchor that uses two component adhesive is called

Answer 27

chemical adhesive

Question 28

when positioning and setting anchor bolts ensure that

Answer 28

each anchor bolt is in its location, sits straight in hole, all of the above

Question 29

in order to ensure anchor bolts in exact location

Answer 29

use a template

Question 30

it is acceptable to weld anchor bolts to rebar

Answer 30

true

Question 31

when the floor of foundation exists the method to find anchor bolts

Answer 31

locate anchor bolts on drawing, find sinch points/ all of the above

Question 32

main reference lines provide

Answer 32

mark from main line

Question 33

a general rule of thumb when working with refernce lines

Answer 33

keep the lines to a minimum so not many errors

Question 34

the main purpose of center lines is to show exact machinery measurements

Answer 34

true

Question 35

center lines are constructed using reference

Answer 35

poiints datums all of the above

Question 36

refernce points are often established close to or

Answer 36

with a brass plug close to or in existing plate

Question 37

when installing piano wire for reference line

Answer 37

install reference point because its taut

Question 38

when using theodolight care must be taken

Answer 38

aligning, checking for error, all of the above

Question 39

jacking screws are used

Answer 39

for shimming

Question 40

most common way to raise a machine in aligment

Answer 40

is shims

Question 41

if a base plate is in an isolated position and level it must be established with an optical tool

Answer 41

use theodolight

Question 42

construction rotating level takes a plain level to take all elevation measurements

Answer 42

plain extends 360 degrees

Question 43

many grouts contain many respritory system

Answer 43

consult msds sheet

Question 44

on a 12 inch master precision level requires .3000 in shim on a bed 4 ft long

Answer 44

.3 x 4 = .012 thou