Ls Flashcards by Antoneo Maurece

What is the normal operating coolant temperature for the M983A4?

180-200 Fahrenheit

How well did you know this?

Not at all

Perfectly

Local launchers are normally emplaced between______meters to _______kilometers in front of the radar

120m-1.3K

How well did you know this?

Not at all

Perfectly

On the M983A4, TACHOMETER is inoperative or indicates less than_____rpm or more than _____rpm at idle after engine has been properly warmed up

625 to 725 RPM

How well did you know this?

Not at all

Perfectly

The tracker wheels must be chocked before driver leaves cab. What kind of hazard is this?

Warning(personal injury can be prevented by a warning)

How well did you know this?

Not at all

Perfectly

What drill number covers pac-2 emplacement

44-CW-D0130

How well did you know this?

Not at all

Perfectly

Prepare for movement for the PAC2.”, how long do you have to complete the drill?

25 minutes

How well did you know this?

Not at all

Perfectly

According to 44-CW-D0200 list in number sequence the power down steps of the DLTM-PDU

a. Processor fault IND
b. DGTL processor
c. SBU
d. PWR supply
E. Radio
F. Blower
G. Maps
H. Maps(AEE)
I. Lamps

How well did you know this?

Not at all

Perfectly

Ungrounded explosives are a potential source of danger from static electricity. The GMT and LS meat be grounded at all times when loaded with tactical GMs. What safety hazard is this considered?

Warning

How well did you know this?

Not at all

Perfectly

When testing the engine brake you must push in the throttle pedal and increase engine speed to between_____ and ______

1650 to 2100

How well did you know this?

Not at all

Perfectly

According to TC 3-01.86 what Basic Gunnery Table do you first conduct missile reload?

Table 3

How well did you know this?

Not at all

Perfectly

How high should the front outriggers be off of the ground when performing Jerk Test?

Just clear of the ground 1-2 inches

How well did you know this?

Not at all

Perfectly

According to the M860 Technical Manual, what makes the fifth wheel kingpin mounting
plate non-mission capable?

Mounting Plate Cracked or Broken

How well did you know this?

Not at all

Perfectly

The proper procedure for exercising the M860 trailer outriggers, how many times does the operator need to move it up and down weekly for PMCS?

Once a week (weekly PMCS is done ONCE a week so only ONCE the outriggers need to be lowered)

How well did you know this?

Not at all

Perfectly

What does the acronym ELES stand for?

Enhanced Launcher Electronic System

How well did you know this?

Not at all

Perfectly

The launcher rear (back blast) area is ______ meters directly behind the launcher and
this area must be clear at all times of personnel and equipment?

90 meters

How well did you know this?

Not at all

Perfectly

When draining the Fuel/water separator keep the drain open until only ____ _____ is flowing out of drain tube.

Pure/clear Fuel

How well did you know this?

Not at all

Perfectly

When conducting BEFORE PMCS on the M983A4 what will cause the Driver Side Air Springs to be NMC?

Ball valves have cracks or damage that would prevent normal operations

How well did you know this?

Not at all

Perfectly

During normal operation what should the Battery Gauge read for the M983A4 HEMTT?

25 vdc to 30 vdc

How well did you know this?

Not at all

Perfectly

You are running a BITE Test on the PAC 2 LS. The BITE Test for the PAC 2 LS should
cycle on and off for at least _____ seconds?

6 seconds

How well did you know this?

Not at all

Perfectly

What does the acronym LMRD stand for?

Launcher Missile Round Distributor

How well did you know this?

Not at all

Perfectly

In accordance with TM 9-2320-340-10, what type of Air leak deadlines a M983A4
HEMTT?

Any air leak (because you cannot measure an air leak)

How well did you know this?

Not at all

Perfectly

What does the acronym FOCA stand for?

Fiber Optic Cable Assembly

How well did you know this?

Not at all

Perfectly

TRUE/FALSE) each launch enable/disable switch is set to disable to prevent
inadvertent launch command signals from the ECS when electrical power is applied.

True (if switch is set to DISABLE than the missiles cannot be misfired)

How well did you know this?

Not at all

Perfectly

What does the acronym MRCTS stand for?

Missile Round Cable Test Se

How well did you know this?

Not at all

Perfectly

How many and define each Alert States

AS1 ABT-ALL AS2 TBMs-TANGO AS3 Passive search-PISS AS4 Radiate Disable-RED AS5 Commanders Discretion- COMMAND AS6 Maintenance-MAD AS7 NMC/Destroyed-NUKES AS0 Transit- TIME NOW

TRUE/FALSE) PAC 3 missiles can be fired on a PAC 2 LS?

False (PAC 2 can only fire PAC 2 missiles)

What drill number covers Pac 3 Prepare for Movement?

44-CW-D0200

What piece of equipment replaced the LMRD on the PAC-3 launching station?

LSDU/J-Box (Junction Box)

When does time stop for Forklift reload?

When the Launcher is in remote.

What two crew member are interchangeable on GMT reload?

CM4 and CM5 (The Signal and the operator)

For decentralized reload, CMs 1 and 2 must perform steps _ through _ before GMT reload team arrives. REF: 44-CW-D0161

Steps 1-6 for Decentralized Steps 1-7 for Centralized

Forks should not extend more than _____ past the edge of the GM canister(s) when being placed on the LS?

6 in

What does MSE stand for?

Missile Segment Enhancement

If one of the missile hazard lights come on and a live missile is present with GM cable connected at location (as indicated by a light) what are immediate actions?

Contact Commander, Notify the ECS, place launcher in local, evacuate the area.

The tilt warning system on the GMT (the model we currently use) will sound at what degrees?

+/-7 degrees (this is the only GMT model they are referring to not the OLD model)

What drill number covers PAC3 Emplacement?

44-CW-D0190

TRUE/FALSE) at idle, engine oil pressure can drop as low as 5psi, this is a normal conditi

TRUE

TRUE/FALSE) If one hinge-pin is broken on the GMT it is FMC?

FALSE (it is NMC)

What are the 2 types of GMT reload?

Centralized and Decentralized (Centralized is when missiles are in the reload area, decentralized is when the missiles to be loaded on the LS are not an the reload area)

During GMT reload (not MSE) how are the Loaded cans placed on the Launcher?

LL, UL, LR, UR

TRUE/FALSE) Due to sling capacity, LOADED PAC-3/PAC-3 MSE munitions are always moved one four- pack or two-pack at a time?

True (they can be moved both ways in the question)

Which CM inspects the beam for GMT reload?

CM3 (CM3 is the safety and Highest ranking so they should check the beam)

Smoking is forbidden within how many feet of all designated reload areas?

100ft

(TRUE or FALSE): Forklift missile reload may be performed from the MSA, GMT, or a flatbed-type carrier?

True (it can be performed from all of these)

Keep hands and feet away from forklift forks to prevent injury. What safety hazard is this?

Warning (personal injury can be prevented by a warning)

According to TC 3-01.86 what Basic Gunnery Table do you first Conduct reload Operations?

Table 3

When performing reload with the GMT either parallel or perpendicular the GMT should be located ____ to ____ feet away from the launching station?

6-9ft on leveled ground. (7-9ft on uneven ground)

During a GMT Reload, which crewmember is responsible for grounding the missiles with the LS missile ground cables?

CM2 (this will be the tag that is on the end closest to the ground cables)

The proper pressure of the fire extinguisher is ____ psi.

150psi

What is the minimum training site area needed for GMT reload?

20 x 25 meters (GMT crane can maneuver in a tighter/smaller space than Forklift)

What is the minimum training site area needed for forklift reload?

40 x 50 meters (forklift needs a lot more space to move cans away from LS)

What does the acronym BITE stand for?

Built In Test Equipment

What drill number covers GMT Reload?

44-CW-D0160 (GMT is a bigger vehicle than the forklift so it gets a “bigger” drill number)

(TRUE/FALSE) PAC 3 missiles can be fired on a M903?

True (M903 is an MSE launcher and is able to fire both PAC3 and MSE)

When does time start for Forklift reload?

When Launcher remote key is in local

According to TC 3-01.86 what Basic Gunnery Table do you get evaluated on PMCS?

Table 1 (Basic System Skills)

What does 44-CW-D0150 cover?

Forklift Reload (forklift is a smaller vehicle than the GMT so it gets a “smaller” drill number)

What is the angle of the LS Platform when it is elevated?

38 degrees

What is the first item checked when conducting AFTER PMCS on the M983A4?

Underneath the vehicle (checking for any leaks or damage)

Prepare for Movement for the PAC3, how long do you have to complete the Drill?

25 minutes

During troubleshooting procedures of the 15KW generator, low oil pressure can be caused by:

C, Air intake not clear and low coolant (this question will be multiple choice like such) A) Air intake not clear B) Low coolant C) All of the above D) None of the above

TRUE/FALSE) The HEMTT is not considered NMC if the Air Warning Light illuminates, but the Warning Buzzer does not operate.

False (The warning buzzer not operating while the air warning light illuminates makes this HEMTT NMC (non mission capable))

You have a Spring Assembly that is missing a rubber bumper. IAW the trailer TM, what status code do you place on the DA 5988-e or DA 2404?

X-deadline

In accordance with TM 9-2320-340-10, what type of Air leak deadlines a M983A4 HEMTT?

Any air leak fitting or damage (because you cannot measure an air leak)

(TRUE/FALSE) Each launch enable/disable switch is set to enable to prevent inadvertent launch command signals from the ECS when electrical power is applied.

False (if set to ENABLE than you could have an inadvertent launch)

T/F Once CM2 passes the DLT antenna to CM1, he/she may immediately work on other tasks

False (CM1 still needs to verify the torque wrench values with CM 2 before moving to other tasks

How often does the operator conduct preventive maintenance checks and services for the level vial on the Gunner’s Quadrant for cracks, broken, or loose vial which can cause an elongated bubble.

Before during and after (every time you use the Gunner’s quadrant you will do PMCS before during and after use)

Forklift Reload hat does 44-CW-0161 cover?

MSE reload (the only not 0 ending drill number)

What does 44-CW-0190 cover?

PAC 3 Emplacement (Prepare for movement (ending in 200) is always after Emplacement)

What does 44-CW-0130 cover?

PAC 2 Emplacement (Prepare for movement (ending in 140) is always after Emplacement)

During a Forklift Reload, which crewmember is responsible for grounding the missiles with the LS missile ground cables?

CM 4 (this is the signaling crew member)

What does the Acronym PBIT stand for?

Power up Built In Test

What does 44-CW-D0140 cover?

PAC2 Prepare for movement

If you pull the GMT outrigger lever down will this raise the outrigger or lower it?

Lower (down = lower)

What markings are displayed for a canister with live missiles?

4in yellow square in the upper right rear corner and upper left front corner

Before conducting missile select ability the STRAY/NO VOLTAGE TEST for the PAC-3 power and signal cables are connected to the J-BOX/LSDU _____ and _____ connectors?

J14 & J16

TRUE/FALSE) During PAC-3 missile selectability you are permitted to put the launcher in remote.

False (could fire an inadvertent launch)

If GMT is out of level more than 5 degrees, unlevel indicator will light (YELLOW) and buzzer will sound. Use of crane in unlevel position may cause GMT to tip over and cause personal injury and damage to equipment. What hazard is this?

Caution (cautions have to do with damaging equipment)

What drill number covers GMT Reload?

44-CW-D160

(TRUE/FALSE) It is permitted to leave live PAC-3 missile canisters ungrounded for up to 4 hours as long as you have a deliberate risk assessment signed by the Battery Commander.

False (you only need a deliberate risk assessment signed by the commander if OVER 4 hours)

What drill number covers Pac 3 Prepare for Movement?

44-CW-D0200

The MRCTS takes about ____ seconds to go from step 00 to 99?

60 seconds

Paperwork showing that a valid and current load test has been performed within the last ______ must be on hand before any reload operation can be conducted?

12 months

Name the 3 reload configurations:

Parallel (6-9 ft) Perpendicular (6-9 ft) End to End (1-3 ft)

What are the three positions for the Engagement Control Handle?

Rotate, Elevate, Road march

What is the travel speed for ground guiding the Forklift?

Walking pace of ground guide

If you pull the GMT crane lever to the max will this speed up the crane or slow it down?

Speed up (MAX = MORE SPEED)

PAC2 Emplacement: manual

44-CW-0130

PAC2 Prepare for Movement manual

: 44-CW-D0140

FL Reload: manual

44-CW-D0150

GMT Reload:

44-CW-D0160

MSE Reload: Manual

44-CW-D0161

PAC3 Emplacement: manual

44-CW-0190

PAC3 Prepare for Movement:

44-CW-D0200

WARNING (

Harm to personnel)

CAUTION (

Damage to Equipment)

DANGER (

Death i.e. being under loaded load)