Paper 2 Required practicals Flashcards Preview

11BT > Paper 2 Required practicals > Flashcards

Flashcards in Paper 2 Required practicals Deck (36)
Loading flashcards...
1
Q

Elasticy PAG - Describe a suitable method

A

Hang a spring off a clamp stand

Measure the original length of the spring

Add a 1 N weigth and measure the final length of the spring with a ruler

Calcualte the extension (final length - original length)

Repeat for weights 2, 3, 4, 5 and 6 N

2
Q

Elasticy PAG - State the variables and whether they are continuous, discrete or catergoric

A

Independent - Weight (continuous)

Dependent - Extension (continuous)

Control - Spring constant (continuous)

3
Q

Elasticy PAG - What type of graph should you draw? Why?

A

Line - both variables are continuous

4
Q

Elasticy PAG - Describe the expected results

A

Forces is directly proportional to extension as long as the elastic limit hasnt been passed.

The graph should be a straight line through the origin up to the elastic limit.

5
Q

Elasticy PAG - What is the main cause of error and how can it be reduced?

A

Parallax error not having your eye level with the spring when measuring its extension.

Reduce this my placing a wooden splint horizontally at the bottom of the spring.

6
Q

Elasticy PAG - Describe a suitable risk assessment

A

Clamp stand may topple - this could fall and hurt your foot - place a counter weigth on the base of the clamp to stop it toppling

7
Q

Elasticy PAG - Describe elastically deformed

A

The object will return to its original length when all forces are removed

8
Q

Elasticy PAG - Describe inelastically deformed

A

An object wont return its original length once all forces are removed, it has been permanently stretched.

9
Q

Elasticy PAG - State Hooke’s law equation

A

Force (N) = Spring constant (N/m) x extension (m)

10
Q

Elasticy PAG - how can the spring constant be found from a graph of force against extension

A

From the gradient

11
Q

Newton’s second law PAG - state the relevant equation

A

Resultant Force (N) = mass (kg) x acceleration (m/s2)

12
Q

Newton’s second law PAG - Describe a suitable method

A

Attached a piece of card of known length to a trolley.

Attached some string to the trolley running over a pulley.

Place a 1 N weigth on the end of the string and allow it to accelerate the trolley through two light gates.

Use the light gates to measure the acceleration of the trolley

Repeat for 2, 3, 4, 5 and 6 N

13
Q

Newton’s second law PAG - State the variables and whether they are continuous, discrete or catergoric

A

Independent - Resultant force (continuous)

Dependent - Acceleration (continuous)

Control - mass of trolley (continuous), Material of surface (discrete)

14
Q

Newton’s second law PAG - State the expected results

A

As resultant force increases the acceleration will increase. They are directly proportional to each other so the graph should be a straight line through the origin.

15
Q

Newton’s second law PAG - Describe a risk assessment

A

Falling masses - could land on your feet - stand away from the experiment

16
Q

Newton’s second law PAG - If the resultant force was kept constant but the mass of the trolley was increased what results would you expect?

A

As mass of the trolley increases the acceleration will decrease, they are inversley proportional to each other.

17
Q

Newton’s second law PAG - What type of graph should you draw? Why?

A

Line - both variables are continuous

18
Q

Newton’s second law PAG - How can a light gate measure velocity?

A

Tell the data loger the length of card (distance)

The light gate will measure the time the card blocks the laser.

Velocity = distance / time

19
Q

Newton’s second law PAG - How can two light gate measure acceleration?

A

Light gate 1 measures initial velocity

Light gate 2 measures final velocity

Light gate measure the time between light gates

acceleration = change in velocity / time

20
Q

Absorption PAG - Describe a suitable method

A

Fill the Leslie cube with boiling water,

Measure and record the starting temperature.

Measure and record the final temperature after 10 minutes.

Calcualte the temperature difference.

21
Q

Absorption PAG - State the variables and whether they are continuous, discrete or catergoric

A

Independent - Coulour of the surface (catergoric)

Dependent - Temperature change (continuous)

Controls - Starting temperature (continuous), Surface area (continuous)

22
Q

Absorption PAG - Describe a suitable risk assessment

A

Boiling water - can burn - place leslie cube in the middle of the desk and stand up

23
Q

Absorption PAG - What graph should you draw why?

A

A bar chart as one of the variables is categoric

24
Q

Absorption PAG - Describe the expected results

A

Light shiny surfaces are the best reflectors of heat so will have the highest temperature at the end of the experiment

Dull dark surfaces are the best absorbers and emitters of infrared radiation so they will have the lowest temperature at the end of the experiment.

25
Q

Reflection and refraction PAG - Describe the law of reflection

A

The angle of incidence = the angle of reflection for a flat plain mirror

26
Q

Reflection and refraction PAG - Describe refraction

A

The changing of direction of a wave as it enteres a new material.

27
Q

Reflection and refraction PAG - Why does refraction take place?

A

The new material has a different density so causes a change in speed.

28
Q

Reflection and refraction PAG - When will a wave refract towards the normal?

A

When the wave slows down

29
Q

Reflection and refraction PAG - When will a wave refract away from the normal?

A

When the wave speeds up

30
Q

Reflection and refraction PAG - If a wave moves from air into glass how are the following effected?

Speed

Wavelength

Frequency

A

Speed - slows down

Wavelength - decreases

Frequency - stays the same

31
Q

Reflection and refraction PAG - If a wave moves from glass into air how are the following effected?

Speed

Wavelength

Frequency

A

Speed - increases

Wavelength - increases

Frequency - stays the same

32
Q

Reflection and refraction PAG - What are the main sources of error and how can they be reduced?

A

The beam of light spreads out so it is hard to judge the centre of the ray of light.

Use a laser and repeat readings

33
Q

Reflection and refraction PAG - What are the main sources of risk?

A

The bulb will get hot - this could burn - turn off and let it cool down before moving it

34
Q

Wave measurments (Ripple tank) PAG - Describe how the speed of water waves can be found using a ripple tank

A

Measure the wavelength using a ruler. Measure across as many waves as possible. Divide the total length by the number of waves.

Measure the frequency using a stop watch. Time for 10 seconds and count how many waves pass a point. Divide the number of waves by 10 seconds to find the frequency.

Calcualte the wave speed using the equation

Speed (m/s) = Frequency (Hz) x Wavlength

35
Q

Wave measurments (Ripple tank) PAG - State the wave equation

A

Speed (m/s) = Frequency (Hz) x Wavlength

36
Q

Wave measurments (Standing waves) PAG - Describe how to calcualte the speed of standing waves.

A

Record the frequency off the signal generator.

Measure the wavelength with a meter ruler. To make this more accurate measure as many wavelengths as possible and divide the total length by the number of wavelengths.

Calcualte the wave speed using the equation

Speed (m/s) = Frequency (Hz) x Wavlength