Past Papers MCQ Flashcards
(31 cards)
Which of the following is an acceptable certificate of release to service for a repaired aircraft component within the EU?
a.
EASA Form 1.
b.
EASA Form 8130.
C.
EASA Form CRS.
a.EASA Form 1
Where are you most likely to find the mass and balance limitations for an aircraft?
A. IPC.
B. Maintenance Manual.
C. Flight Manual or Pilot Operating Handbook.
C. Flight Manual or Pilot Operating Handbook.
In a wiring loom, what is the recommended bend radius?
A. 1 x Diameter of largest wire in the loom.
B. 10 x Diameter of largest wire in the loom.
C. 20 x Diameter of largest wire in the loom.
C.
20 x Diameter of largest wire in the loom.
What would you use a Megger for?
a.Continuity testing.
b.Bonding testing.
c.Insulation testing.
c.
Insulation testing.
What is the flaring angle for flared x fittings?
A.30°
B.37°
C.45°
B.37°
Is liquid penetrant inspection a suitable method for detecting subsurface defects?
A.
Yes.
B.
Only for aluminium materials.
C.
No.
C.No
Which of the following bearings only withstands radial loads?
A.
Ball bearing.
B.
Roller bearing.
C.
Tapered bearing.
B.Roller bearing
In which ATA Chapter would you find scheduled maintenance intervals?
A.Chapter 5.
B.Chapter 20.
C.Chapter 21.
A. Chapter 5
In aircraft documentation, what does the acronym MEL refer to?
A.Maximum Electrical Listing.
B.Minimum Equipment List.
C.Maintenance Equipment Locations.
B.Minimum Equipment List.
What colour would the band on a COz fire extinguisher be:
a.
Red.
b. Green.
c.
Black.
C. Black
Red Dye Penetrant Inspections is suitable for detecting:
a.
Subsurface defects only.
b.
Surface defects only.
C.
Surface and subsurface defects.
C.
Surface and subsurface defects.
In relation to the diameter dimension viii of electrical wires, which of the following is true?
A.AWG 18 > AWG 8.
B. AWG 18 < AWG 8.
C.Both diameters of AWG
18 and AWG 8 are the same dimension.
B. B. AWG 18 < AWG 8.
What would a microfiche be used for?
A. Storing information.
B.
Measuring diameters of small holes.
C.
Measuring the depth of pitting corrosion.
A. Storing information
What is a shadow board used for?
A. Light measurement.
B. Tool control.
C. Re-assembling an identical part fixed onto another board.
B. Tool
Convert 113°F to *C.
A. 45.0
B. 62.7
C. 94.7
A. 45
A safety meter would be used to
perform:
a. A bonding check.
b. A continuity check.
c. An insulation check.
C. An insulation check
An AN6H-10A bolt has a diameter of:
a. 3/8 Inch
b. 6/32 Inch
c. 10/16 Inch
a. 3/8 Inch
What is the maximum permitted distance between identification markings on an electrical wire?
a. 2 Inches.
b. 6 Inches.
c. 15 Inches
B. 6 inches
In what year was the current Health and Safety at Work act published?
A. 2005
B. 2011
C. 2014
B. 2011
What would you associate a permaswage fitting with?
a. A coax connector.
b. Repair of a hydraulic hose.
c. Swaging a control cable.
C. Swaging a control cable.
What is the ATA Chapter for Landing Gear?
a. 22. b. 32. c. 42.
B. 32
You are asked to open a panel with the following ATA code 334AB. Where would you find the panel?
a. Lower fuselage.
b. Tail section.
c. Port Wing.
A. Lower fuselage
Who issues a Service Bulletin?
a. The Airworthiness Authority.
b. The Manufacturer.
c. The Leasing Company.
B. Manufacturer
In relation to the diameter dimension of electrical wires, which of the following is true?
A. AWG 18 > AWG 8.
B. AWG 18 < AWG 8.
C. Both diameters of AWG
18 and AWG 8 are the same dimension.
B. AWG 18 < AWG 8.
