Rules And Regulations

Question 1

All scaffolds and ladders must have _ on bottom of them

Answer 1

Base plates

Question 2

Ensure level and plumb, max?

Answer 2

1/2” every 10’

Question 3

Ensure scaffold is tied off,
what rule?
Every _
Height intervals?
Length

Answer 3

3:1 rule
5’
15’ height
20’ length

Question 4

What should you do with clamps attached to scaffolds?

Answer 4

Inspect and tighten if appear loose

Question 5

Ensure height clearance is?

Answer 5

6’6”

Question 6

What is the ledger spacing max?

Answer 6

6’6” same as height clearance

Question 7

All transoms must be supported no more than?

Answer 7

5’ intervals

Question 8

Ensure a what brace is installed at base? And cross bracing no more than?

Answer 8

Clam/X/plan brace
15’ intervals

Question 9

Ensure ledgers are connected to standards with what clamp only?

Answer 9

90/right angle clamp

Question 10

All diagonal bracing must be supported at _ intervals unless noted on _ drawings

Answer 10

10’
Engineed

Question 11

Joiners must have ledger tube within _ above and below, scaffolds with joiners must have diagonal _

Answer 11

1’
Bracing

Question 12

Joiners on ledgers (avoid if possible) can lossen with weight overtime and collapse, if you can’t make sure to have supported by solid _ above and below at _ or the node point (standard)

Answer 12

Tube
6”

Question 13

Transoms mounted on ledgers must be _ of the standard or _ point

Answer 13

6”
Node

Question 14

Diagonal bracing is installed between _ to _ • _ is the usual number

Answer 14

Between 30-60 degrees 45 is the usual

Question 15

What’s is correct scaffold platform height for work?

Answer 15

3’-5’ below work

Question 16

Access to scaffold and scaffold platforms should be?

Answer 16

Clear and unobstructed

Question 17

Scaffold access should be minimum of _

Answer 17

22” opening

Question 18

Describe swing gate install

Answer 18

Self closing
36-42” above work platform
Swings away from ladder

Question 19

If swing gate can not be installed what should you use in place of?
And what do you do after installing of them?

Answer 19

Double chain gate
Note on tag

Question 20

Ladders should have _ toe clearance

Answer 20

6”

Question 21

Ladders should extend _ or _ of work platform

Answer 21

36” or 3’

Question 22

Rest deck ladders should be no more than _ between platforms and should be _ of each other

Answer 22

10’
Offset

Question 23

Caged ladder requirements
_ square
Horizontal tube guard rails every _
Max spacing.
Vertical guard rail spacing?
From bottom _ height no less then _
Cage has to extend _ past platform
Max ladder height _
_ required on all ladders

Answer 23

28-30”
4’
14-15”
7’2” max no less then 6’6”
36” or 3’
30’
Baseplates

Question 24

Ensure planks can’t move _ or _

Answer 24

Vertical and horizontal

Question 25

Planks can’t extend more than _

Answer 25

7’

Question 26

Ensure _ clearance from none structural items

Answer 26

1”

Question 27

Aluminum filler plank doesn’t exceed _ space and should be supported by _ at both ends

Answer 27

5” Transom

Question 28

No more than _ wide of aluminum planks are supported by planks on both sides spanning full length of deck

Answer 28

19”

Question 29

Transom connected to aluminum planks extent beyond double bolt connecter _ past

Answer 29

4”

Question 30

Toe bored height is _

Answer 30

5”

Question 31

What should not be at the access of platforms?

Answer 31

Toe bored

Question 32

Aluminum toe board should be secured with _

Answer 32

Toe bored clips or clamps

Question 33

Deck must be _ for defects

Answer 33

Inspected

Question 34

Handrail/ guard rail must be at Midrail height?

Answer 34

36” and 42” Mid way between handrail and platform

Question 35

Any hazard or deviation should be _

Answer 35

Noted on tag

Question 36

Scaffold tag should be updated _

Answer 36

Monthly

Question 37

Scaffold plank should extent a minimum of _ past the standard the max is _

Answer 37

6” 9”