Safety Flashcards
(20 cards)
When is a safety harness required for a lighting technician?
a) When working on the ground
b) When operating a followspot
c) When working at height, such as on a condor or truss
d) When running DMX cables
c) When working at height, such as on a condor or truss
What is the purpose of grounding in a lighting setup?
a) To increase light output
b) To prevent electrical shock by providing a safe path for stray current
c) To reduce cable weight
d) To stabilize light fixtures
b) To prevent electrical shock by providing a safe path for stray current
What should you do if you find an exposed live wire on set?
a) Touch it to test if it’s live
b) Immediately report it and de-energize the circuit
c) Cover it with tape
d) Ignore it if it’s not in use
b) Immediately report it and de-energize the circuit
What is the minimum safe distance from a live electrical panel?
a) 1 foot
b) 3 feet
c) 6 feet
d) 10 feet
b) 3 feet
When should a GFCI be used in a film lighting setup?
a) Only indoors
b) In wet or outdoor environments
c) Only with LED lights
d) When using tungsten lights
b) In wet or outdoor environments
What knot is commonly used to secure cables or equipment on a film set?
a) Square knot
b) Clove hitch
c) Slip knot
d) Bowline
d) Bowline
What should be checked before operating a scissor lift on set?
a) The color temperature of nearby lights
b) The lift’s safety mechanisms and certifications
c) The weight of the cables
d) The type of gels in use
b) The lift’s safety mechanisms and certifications
What does the right to refuse unsafe work mean on a film set?
a) You can leave the set without notice
b) You can refuse tasks that pose a safety risk without repercussions
c) You can refuse to work with certain crew members
d) You can refuse to use specific fixtures
b) You can refuse tasks that pose a safety risk without repercussions
What should you do if a light fixture is not working during a troubleshooting check?
a) Replace the bulb immediately
b) Check if the line is hot, the bulb is burnt out, or a safety switch is disengaged
c) Increase the voltage
d) Add a diffusion gel
b) Check if the line is hot, the bulb is burnt out, or a safety switch is disengaged
What is a key safety consideration when setting a light stand on uneven terrain?
a) Ensuring the stand is lightweight
b) Securing the base with sandbags or stakes for stability
c) Using a shorter stand
d) Avoiding the use of scrims
b) Securing the base with sandbags or stakes for stability
What should be done before touching a hot light fixture?
a) Wear heat-resistant gloves
b) Increase the power supply
c) Add a gel to cool the light
d) Turn on the fixture
a) Wear heat-resistant gloves
What is the purpose of a safety cable on a lighting fixture?
a) To increase light output
b) To secure the fixture in case of mount failure
c) To reduce heat buildup
d) To stabilize power flow
b) To secure the fixture in case of mount failure
What should you do if a generator is overheating on set?
a) Increase the load
b) Shut it down and report to the generator operator
c) Add more fuel
d) Adjust the lighting console
b) Shut it down and report to the generator operator
What is the purpose of a fire watch on a film set?
a) To monitor lighting levels
b) To ensure fire hazards are managed during hot work
c) To operate the generator
d) To adjust color gels
b) To ensure fire hazards are managed during hot work
What should be used to secure cables on the floor to prevent tripping?
a) Duct tape
b) Cable mats or tape designed for safety
c) Sandbags
d) Gels
b) Cable mats or tape designed for safety
What is the maximum weight a C-stand can safely support?
a) 10 lbs
b) 22 lbs
c) 50 lbs
d) 100 lbs
b) 22 lbs
What should you do before climbing a ladder on set?
a) Check the ladder’s stability and weight rating
b) Adjust nearby lights
c) Run additional cables
d) Add diffusion to fixtures
a) Check the ladder’s stability and weight rating
What is the purpose of a lockout/tagout procedure on a film set?
a) To secure lighting stands
b) To prevent accidental energization of electrical equipment
c) To control light intensity
d) To manage DMX signals
b) To prevent accidental energization of electrical equipment
What should you wear when handling hot bulbs?
a) Safety glasses
b) Heat-resistant gloves
c) A hard hat
d) Steel-toed boots
b) Heat-resistant gloves
What is the first step if someone receives an electric shock on set?
a) Move them to a new location
b) De-energize the circuit immediately
c) Check the light output
d) Call the gaffer
b) De-energize the circuit immediately
