SUBELEMENT T2 - Operating Procedures - [3 Exam Questions - 3 Groups] Flashcards
T2A01 (B)
Which of the following is a common repeater frequency offset in the 2 meter band?
B. Plus or minus 600 kHz
T2A02 (A)
What is the national calling frequency for FM simplex operations in the 2 meter band?
A. 146.520 MHz
T2A03 (A)
What is a common repeater frequency offset in the 70 cm band?
A. Plus or minus 5 Mhz
T2A04 (B)
What is an appropriate way to call another station on a repeater if you know the other station’s call sign?
B. Say the station’s call sign, then identify with your call sign
T2A05 (C)
How should you respond to a station calling CQ?
C. Transmit the other station’s call sign followed by your call sign
T2A06 (A)
Which of the following is required when making on-the-air test transmissions?
A. Identify the transmitting station
T2A07 (A)
What is meant by “repeater offset?”
A. The difference between a repeater’s transmit frequency and its receive frequency
T2A08 (D)
What is the meaning of the procedural signal “CQ”?
D. Calling any station
T2A09 (B)
What brief statement indicates that you are listening on a repeater and looking for a contact?
B. Your call sign
T2A10 (A)
What is a band plan, beyond the privileges established by the FCC?
A. A voluntary guideline for using different modes or activities within an amateur band
T2A11 (C)
What kind of communication is taking place when an amateur station is transmitting and receiving on the same frequency?
C. Simplex
T2A12 (D)
Which of the following is a guideline when choosing an operating frequency for calling CQ?
A. Listen first to be sure that no one else is using the frequency B. Ask if the frequency is in use
C. Make sure you are in your assigned band
D. All of these choices are correct
T2B01 (C)
What is the most common use of the “reverse split” function of a VHF/UHF transceiver?
C. Listen on a repeater’s input frequency
T2B02 (D)
What term describes the use of a sub-audible tone transmitted along with normal voice audio to open the squelch of a receiver?
D. CTCSS
T2B03 (B)
If a station is not strong enough to keep a repeater’s receiver squelch open, which of the following might allow you to receive the station’s signal?
B. Listen on the repeater input frequency
T2B04 (D)
Which of the following could be the reason you are unable to access a repeater whose output you can hear?
A. Improper transceiver offset
B. The repeater may require a proper CTCSS tone from your transceiver
C. The repeater may require a proper DCS tone from your transceiver
D. All of these choices are correct
T2B05 (C)
What might be the problem if a repeater user says your transmissions are breaking up on voice peaks?
C. You are talking too loudly
T2B06 (A)
What type of tones are used to control repeaters linked by the Internet Relay Linking Project (IRLP) protocol?
(A) DTMF
T2B07 (C)
How can you join a digital repeater’s “talk group”?
C. Program your radio with the group’s ID or code
T2B08 (A)
Which of the following applies when two stations transmitting on the same frequency interfere with each other?
A. Common courtesy should prevail, but no one has absolute right to an amateur frequency
T2B09 (B)
What is a “talk group” on a DMR digital repeater?
B. A way for groups of users to share a channel at different times without being heard by other users on the channel
T2B10 (A)
Which Q signal indicates that you are receiving interference from other stations?
A. QRM
T2B11 (B)
Which Q signal indicates that you are changing frequency?
B. QSY
T2B12 (A)
Why are simplex channels designated in the VHF/UHF band plans?
A. So that stations within mutual communications range can communicate without tying up a repeater