TB 67: Homatro Rescue Tool Flashcards by Vince de Leon

TB 67: Holmatro

The Power Units utilize a Two-Stage Pump:
The FIRST Stage is ______ psi
The SECOND Stage is _______ psi

3,000 psi

10,500 psi

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

The Power Units utilize a ____ weight Mineral Based Hydraulic Fluid. That is _____ or _____ ________ in color and non-corrosive.

22 weight

Pale or Light Yellow

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

PPU 15: Specs

____ lbs
____ horse power Honda engine
_____ rpm
_____ quarts regular unleaded gasoline
_____ cc usable Hydraulic Fluid

35   lbs
2.5  hp
4,500  rpm
1.3   quarts
2,000  cc

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

DPU 30: Specs

____ lbs
____ horse power Honda engine
_____ rpm
_____ quarts regular unleaded gasoline
_____ cc usable Hydraulic Fluid

58   lbs
3  hp
3,600  rpm
1.5   quarts
3,000  cc

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

There is currently only ONE SPREADER used on Truck companies. Its is Model _____ UL

3260 UL

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

To OPEN the Spreaders rotate the Trigger Handle ______________.

Clockwise

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

A built-in _______ _______ will keep the Spreaders in its current position when the trigger handle is released.

Check Valve

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

The Two SHACKLES are equipped with Grab Hooks used to to connect to the C -___ rated Chain.

C - 8

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

How many Cutter Tips are used for Panel Cutting with the SPREADERS?

ONE

*One spreader tip is used as a base

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

Ensure that the Tips of the CUTTERS Do Not ______ over on the opposite side of the Blades.

Cross

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

3020 UL Cutters:
________ lbs. cutting force
5 1/4” opening
27 1/2 lbs

63,400 lbs.

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

3035 NCT Cutters:
________ lbs. cutting force
5 5/8” opening
33 1/2 lbs

57, 320 lbs

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

4050 NCT Cutters:
________ lbs. cutting force
7 1/8” opening
37 1/2 lbs.

208,000 lbs

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

There is NO provision for the use of the TELESCOPIC RAMS for ___________ operation.

Pulling

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

3340 Telescopic Ram (small):
____ in. retracted
____ in. fully extended
24 lbs

12 in. retracted

23 in. fully extended

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

3350 Telescopic Ram (big):
____ in. retracted
____ in. fully extended
37 lbs

21 in retracted

50 1/4 in. fully extended

How well did you know this?

Not at all

Perfectly

TB 67: Holmatro

The HOSES come in two colors (orange and blue) and are ____ ft. in length.

Study These Flashcards

32 ft.

TB 67: Holmatro

Both INNER and OUTER hoses are contracted of Polyurethane and reinforced withe kevlar-like _______ fibers.

Study These Flashcards

Aramid

TB 67: Holmatro

The Working Pressure of the hose is: _______ psi
The BURST Pressure of the hose is: _______ psi

Study These Flashcards

10,500 psi

42,000 psi (4 times the working pressure)

TB 67: Holmatro

Each pump comes with a PRESSURE RELIEF DEVICE. The device is used by placing the Male end into the hose coupler then turning the Black Knob __________ until the plunger in the male coupler is depressed and a small amount of fluid is released.

Study These Flashcards

clockwise

TB 67: Holmatro

To avoid the buildup of pressure: Spreaders and Rams should be opened ____ of an inch, in the proper storing position.

Study These Flashcards

1/4 in.

TB 67: Holmatro

The RAM SUPPORT has TWO purposes:

Provide a Purchase Point _______ to the object to be pushed.
To spread the force load against the object.

Study These Flashcards

nearer

TB 67: Holmatro

Cutter should be stored with the Tips Crossed. If the Cutter will not fit in the compartment this way, OPEN completely then _______ slightly.

Study These Flashcards

TB 67: Holmatro

Who carries the SECUNET?

Study These Flashcards

Truck Companies

Heavy Rescue

TB 67: Holmatro If an Air Bag deploys into the SECUNET, can it be used again?

NO, manufacturer only guarantees one time deployment. Take out of service and order replacement through S&M

TB 67: Holmatro Visually inspect that ALL fasteners are present and tight is a _________ check?

Weekly

TB 67: Holmatro Weekly Check: The Unit should be started and run for at least ____ minutes to ensure smooth operation.

15 min.

TB 67: Holmatro Weekly Check: Operate the tool to its full OPEN or CLOSED position an continue to HOLD the Trigger Handle for a few seconds. Note the change in RPM before releasing the handle. This ensures that the ______ stage pump is operating and the High-Pressure load will not _______ the Engine.

Second Stall

TB 67: Holmatro Power Unit: - Inspect the Air Cleaner for cleanliness - Hose Couplings for proper operation - Dust Caps and their Tethers - Starter Cord for Fraying - Condition of Fuel These are the _________ checks.

Monthly

TB 67: Holmatro - Check Fuel and Hydraulic levels - Switch ON - Choke ON - Fuel valve ON - Visual Inspection of the Unit to ensure readiness. These are the ________ checks.

Daily

TB 67: Holmatro Spreaders: - Check for Cracks or Gouges in the Arms - Cracks or deformities in the Main Body - Check Spring Loaded Quick Pins on Tips - Pins should move freely in both directions. - Check Tips for cracks and excessive wear. These are the __________ checks for the Spreaders.

Monthly

TB 67: Holmatro Spreader Tips should be replaced if either of these conditions exist? 1. __________ 2. ________ ______

Cracks Excessive Wear

TB 67: Holmatro Cutters: When do you check the HINGE BOLT for tightness? How many pound of torque do you tighten it to?

Weekly 75 lbs of torque

TB 67: Holmatro Cutters: - Check for Nicks, Cuts, and Gouges. - If nicks begin to "Mushroom" dress with a file so the blades pass each other without deflection. These are _________ checks.

Weekly

TB 67: Holmatro Telescopic Rams: - Extend the Rams Fullly, checking for Gouges or Sharp Points that may damage the end _____ and cause leakage. - Inspect the small _______ tube that runs along the main body of the Ram. This is a Return Tube and if bent or punctured will leak fluid under pressure. These are ________ checks.

seals chrome MONTHLY

TB 67: Holmatro Because the HOSES are the most abused component of the Holmotro system. Check for CRACKS, HOLES, or ABRASIONS that may cause leakage. Hold the trigger to the full Open or Closed position for about ___ to ___ seconds and check for leaks. These are ________ checks.

5 to 10 sec. Weekly

TB 67: Holmatro Hoses should be cleaned with ______ ______ and _____ _____. If they are contaminated with grease, tar, or battery acid wipe clean with a cloth dampened with ______. These are ________ checks.

Mild Soap Warm Water WD40 WEEKLY

TB 67: Holmatro When do you check all accessories (SECUNET, HRS-22 RAM SUPPORT, Chain Shackles, Chains) ?

Monthly

TB 67: Holmatro Current LAFD policy is to replace fuel in Small Motors every ____ days. To check your gasoline's freshness, pour small amount into a metal receptacle. If the fuel is the color ______ dump and replace.

30 days yellow

TB 67: Holmatro If the Power Unit runs Rough or Stalls in the RUN position, contact the small engine repair mechanic. Running the power unit in the _____ _______ position for extended periods of time can cause damage to the engine components.

Half Choke

TB 67: Homatro Rescue Tool Flashcards

(40 cards)