Brainscape's Knowledge GenomeTM


Top Flashcards (Certified)
All Flashcards

Crane School > Test 3 > Flashcards

Test 3 Flashcards

(86 cards)

Start Studying
1
Q

All slings for riging must have:

A

Sling identification

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

While performing a shift inspection, which one of these are required to be inspected as per OSHA 1926.1412

A

Hooks and latches for deformation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What is the maximum amount of wear in the saddle of a hook that is allowed according to the B 30.10 standard for load hooks

A

10%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Which of the following would most likely be considered a non-standard attachment

A

Pile lead adapter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

According to OSHA table A, what is the minimum clearance required when working near a powerline of 400 kV

A

25ft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Which of the following is the best definition of gross load

A

The weight of the loan plus other items, such as the hook block, rigging, etc.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Who is required to approve crane set up according to the B 30.5 standard

A

Crane operator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

On a typical boom truck, what task does the PTO perform

A

Engage hydraulic pump

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

While setting up a crane, a poor location would be

A

Above utilities

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

When performing pick and carry operations, what is the maximum speed

A

Set by the manufacture

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is the purpose of an integral holding device on the hydraulic cylinder

A

Prevent uncontrolled retraction if hydraulic line connection is lost

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

When the jib is installed on the crane you are running, but it’s not being used, what is the deduction for the rope running up the back of the boom and jib

A

No deduction

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

According to OSHA 1926.1401, a drum rotation indicator as a device on a crane or a hoist which

A

Indicates which direction and speed a particular hoist drums turning

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

When using a boom attached personnel platform, when is it acceptable for the occupants to not use a safety harness

A

When working over water

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

While operating a truck mounted crane, and swinging a load from over the side of the front, what would be the greatest danger

A

No capacity over the front

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

If the crane has 1 inch diameter rope what is the minimum pitch diameter of the sheaves of the lower load block

A

16 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

The abbreviation PTO on a crane stands for what

A

Power takeoff

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

While performing a shift inspection, which one of these are required to be inspected as per OSHA 1926.14 12

A

Ground conditions

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What would be the effect of hoisting a load at high speed

A

Increase dynamic loads

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

A work area chart is used to

A

Determine what quadrant of operations you may be working in (front, side, rear)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

According to OSHA 1926.1412, what person is required to perform the shift inspection

A

Competent

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Using a range diagram, boom length an angle can be used to determine

A

Load radius

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Rapid acceleration while hoisting would most likely produce

A

Increased weight to load block

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

A crane with 120 ft boom will be operating at 42 foot radius. The load chart has a capacity of 40 feet radius and one at 45 foot radius. Which radius will you use to find a gross capacity

A

45 foot

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
What are the proper audible travel signals were working with Cranes
One beep stop, to beeps forward, three beeps back
26
Blocking under Outrigger pads should be at least
Three times the size of foot pad area
27
When setting up a crane near a cinderblock wall what is the minimum distance that should be maintained between the rear of the rotating superstructure and the wall
2 feet
28
When a land Cran is working on a barge the red capacity of the crane may be modified to account for which of the following
List and trim
29
One setting up your crane you’re a newly constructed building the ground is more likely to be
Soft
30
We’re approaching a job site with a crane your first concern should be ____
Access road compaction
31
What is the function of a load indicator
Indicates actual load weight
32
Cribbing Or blocking that has spacing in between blocks are most likely to cause
Stability decrease
33
Which condition is present when lifting heavy loads with the boom of a crane
Boom deflection
34
A qualified crane operator is required to pass a physical exam every _____years according to ASME B 30.5
3
35
The axis of rotation of a crane is
The vertical axis around which the superstructure rotates
36
The term reeving means
A rope system in which Rope travels around drums and sheeves
37
At what percentage of the maximum line pulled his OSHA requires the operator to test the hoist break
90%
38
The telescopic Crane you are operating has 100 feet of main boom fully extended and a 40 foot extension erected. The actual boom angle is 66°. While lifting the load from the extension, the load chart for the extension has a capacity at 66.9° and one at 64.8°. Which angle will you use to find a gross capacity
64.8
39
When hooking and unhooking a load in the fall zone which of the following is required
Self latching hook
40
When working your powerlines there are less than 350 KV, but you do not know the exact voltage what is the minimum clearance that must be maintained
20 feet
41
When traveling a crane under powerlines that you may get closer than 20 feet too, what is required
A dedicated spotter
42
Before lifting operations commands, who is responsible for ground preparations
The controlling entity
43
When setting up your crane on uneven ground, what is the most important to remember
Make sure Outrigger pads are at right angles to the vertical Jack
44
When setting up your crane, which one of these should be done
Cribbing is larger than pad
45
As used in 1926 sub part CC, the term “must” is
Mandatory
46
If the load is being pulled at an angle to the vertical axis of the boom he affect would be
Sideload
47
Crane stability or tipping is based on
Leverage or leverage principal
48
Jib extension capacities are generally based on
Structural strength
49
When lifting off the main boom, how was the effective way of the jib/extension different in the erected position opposed to the stowed position
Effective weight increases
50
If the read out on an operational a does not match the crane little chart ratings what should be used
Load rating chart
51
When performing a proof test on a personal platform, what is required
125% load test
52
According to the 1926 subpart cc a monthly inspection is
He documented shipped inspection
53
What must never be done to a crane’s hoisting cable
Splice
54
In what quadrant or area of operations will cause the greatest out rigger loading
Corner
55
According to OSHA table tea, what is the minimum clearance distance required with an 8 kV powerline
6 feet
56
Hey anti two lock device is a
Device when activated disengages all crane functions whose movements can cause two blocking
57
Who must determine maximum speed at a job site for a mobile crane traveling with a suspended load
A competent person
58
Using a telescopic crane and lifting off the jib/extension with the Main boom partially extended, you should use the_________ To determine gross capacity
Boom angle
59
When hoisting personnel what is required
Must have A2B device
60
According to 1926 subpart cc, a directional drum rotation indicator is a device on a hoist or crane which
Indicates in which direction and what relative speed particular hoist is turning
61
What device listed is not required on a telescopic boom crane manufacture today
Swing path monitor
62
When blocking under a cranes out rigger floats, the blocking should be
Parallel to outrigger beam and tightly spaced
63
Arrange diagram is used to
Determine the radius, angle, or tip height the crane may be at
64
Proper blocking includes
Making sure Outrigger pads are 90° to the vertical Jack
65
Where ship powerline warnings be located on the crane
Inside the cab and outside of the crane
66
Where is a drum rotation indicator required on Cran’s built after November 8, 2011
When hoist is not visible to the operator
67
Well using it to like bridal I would changing from 30° to 60° sling angle effect sling tention
Less tension
68
If an operator of setting up a crane what should be checked
Soil and ground condition
69
A crane set up that is within 1% level Cran has 100 feet of boom out at a high boom angle the load line will be no greater than how far off the set an a lot of the boom
12 inches
70
According to federal regulation, equipment with a luffing jib must have
A luffing jib limiting device
71
What would be a great indication that you have cord damage while using rotation resistant wire rope
Reduction of rope diameter
72
If a truck crane is operating with the out rigors fully extended and set but does not have its front down riggers set The operator should
Refer to my factors working area diagram
73
What type of material should not be used around synthetic nylon slings
Acid
74
When Performing crane operations near new excavation, what could cause it to collapse
Vibration
75
The telescopic crane is equipped with an anti-to block device. When the device is activated, which functions will be generally disabled
Hoist up, extend out, lower boom
76
What are on jib/ extensions load capacity is generally based on
Structural strength of the jib extension
77
When does OSHA requires taglines to be used
When rotation of the load would be hazardous
78
What is the number of broken wires in a role-play that would require a standing rock to be replaced
And connection to broken, beyond and connection three broken
79
When should an operator use signs of tipping determine capacity limitations
Not an acceptable practice
80
The red area of an instrument gauge means
Dangerous condition
81
Load charts are designed during what operation of the crane
Static motion
82
Greater sling angle has what effect
Increased tension
83
On the job site who is responsible to follow manufacture procedures for assembly and disassembly
Owner/employer
84
Who’s responsibility is it to ensure ground preparation has been completed before crane set up
Controlling entity
85
Outrigger blocking or cribbing must be
Capable of supporting crane
86
With a telescope in crane if the boom sections are supposed to be extended equally and they are not, what is the most likely to happen
The longer section will have more stress

Crane School (3 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2025 Bold Learning Solutions. Terms and Conditions