Traps, Interceptors, Separators & Vents Flashcards

Understand the function and installation of traps and interceptors, along with venting systems and configurations in plumbing installations. (30 cards)

1
Q

Fill in the blank:

The vertical distance from the fixture outlet to the trap weir shall not exceed ______ inches.

A

24 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Fill in the blank:

A combination plumbing fixture is permitted to be installed on one trap provided that one compartment is not more than ______ inches deeper than the other compartment.

A

6

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Where is a slip joint connection of a trap not permitted?

A

trap offset

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Fill in the blank:

Each fixture trap shall have a trap seal not more than ______ inches deep.

A

4

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

True or False:

A trap shall be larger than the drainage pipe into which the trap discharges.

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

True or False:

Acid resistant traps shall be embedded in concrete.

A

True

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Which location does not require a grease interceptor or automatic grease removal device?

A

residential kitchen

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the grease retention capacity for an interceptor with a flow-through rate of 10 GPM?

A

20 pounds

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Fill in the blank:

______ shall be provided for inspection and maintenance of automatic grease removal devices.

A

Ready access

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Fill in the blank:

A wire basket on the discharge side of a clothes washer shall prevent the passage of solids ______ inch(es) or larger from being discharged into the public sewer.

A

1/2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

True or False:

The plumbing vent system may be used for purposes other than venting of the plumbing when approved by the code official.

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Fill in the blank:

Where a rooftop is used for restaurant dining, open vent pipes shall terminate not less than ______ feet above the roof.

A

7

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Fill in the blank:

Any increase in size for vent terminations shall be created not less than ______ inside the thermal envelope.

A

12 inches

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Fill in the blank:

A vent stack is required when there are more than ______ branch intervals in a building.

A

five

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Fill in the blank:

If a vent extends more than ______ feet in developed length, then the vent shall be increased by one nominal pipe size for the entire length.

A

40

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What is the vent pipe size for a drainage system serving a 4” stack carrying 300 DFU with a developed length of 75 feet?

17
Q

True or False:

The developed length may be measured from the farthest point of vent connection to the drainage system to the vent termination outside the building.

18
Q

Fill in the blank:

Relief vents shall be provided for stacks having ______ or more branch intervals

19
Q

What is the maximum distance for a trap arm for a 1 1/4” trap with 1/4” per foot grade?

20
Q

What is the maximum distance for a trap arm for a 3” trap with 1/8” per foot grade?

21
Q

True or False:

Common vented trap fixtures shall be located on the same floor level.

22
Q

True or False:

Fixtures being vented by a horizontal wet vent must be on the same floor level.

23
Q

True or False:

A waste stack vent system is permitted to have 45-degree offsets within the stack.

24
Q

What is the maximum number of fixtures that can be served by a circuit vent?

25
# True or False: When a circuit vented drain connects to a stack receiving waste from above, a relief vent is required.
True
26
Which of the following fixtures is permitted to be served by an island fixture vent? a. water closet b. urinal c. sink d. service sink
c. sink
27
What is the maximum distance for a horizontal branch serving fixtures other than toilets in a single stack vent system?
12 feet
28
What is the minimum pipe size for a fixture branching vertically from a horizontal branch in a single stack vent system?
2 inches
29
# Fill in the blank: In a single stack vent system, stacks greater than two branch intervals shall not receive discharge from horizontal branches on the lower \_\_\_\_\_\_ floors.
two
30
# True or False: Air admittance valves shall be permitted to be installed in plenums.
False