unit 3 Flashcards
(80 cards)
1
Q
A welder performance qualification test:
Select one:
a. Is a practical welding test
b. Must be completed immediately after the welder obtains a certificate of qualification.
c. Is only required by welders working on steel structures
d. Is only required once in a welder’s career
A
a. Is a practical welding test
2
Q
Water expands approximately ________ times when converted to steam
Select one:
a. 1600
b. 6000
c. 10,000
d. 100
A
a. 1600
3
Q
An international code which has been adopted and is enforced by all jurisdictions is the: Select one: a. Act b. CSA B52 c. ASME Code d. CSA B51
A
c. ASME Code
4
Q
This group recommends updates to the learning materials of each class of Power Engineer, and the criteria required to ensure a Power Engineer is properly qualified when a Certificate of Competency is issued. Select one: a. SOPEEC b. ASME c. ANSI d. IPECC e. ACI
A
d. IPECC
5
Q
The main or primary document which must be passed through the jurisdictional parliament is a/an: Select one: a. Edict b. Regulation c. Proclamation d. Bill e. Act
A
e. Act
6
Q
It much easier to have changes made to a regulation than it is to have changes made to a/an: Select one: a. Act b. Edict c. Bill d. Proclamation
A
a. Act
7
Q
Which of these is the "Mechanical Refrigeration Code"? Select one: a. ASME Section I. b. ASME MRC c. CSA B52. d. CSA B51.
A
c. CSA B52.
8
Q
One of the national legislative items which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the: Select one: a. NAFTA Codes b. ANSI Codes c. NFPA Codes d. ASME Codes e. CSA B52
A
e. CSA B52
9
Q
Power engineers can usually expect to work: Select one: A. Straight 8 hour night shifts B. Rotating shifts C. Straight 12 hour night shifts D. Straight 12 hour day shifts
A
B. Rotating shifts
10
Q
What code contains Rules For Construction of Power Boilers? Select one: a. CSA B51. b. ASME Section VIII. c. CSA B52. d. ASME Section I.
A
d. ASME Section I.
11
Q
To register a boiler, pressure vessel, a pressure piping system, or a boiler fitting, within one of the provincial jurisdictions,
Select one:
a. The chief inspector of the jurisdiction must review and approve the design drawings and calculations
b. Drawings must be submitted to the ASME
c. The manufacturer need not have a quality control program in place
d. The CSA must approve the design
A
a. The chief inspector of the jurisdiction must review and approve the design drawings and calculations
12
Q
When applying to write a Power Engineer certificate of competency examination, the candidate must:
Select one:
a. Undergo mandatory drug testing
b. Hold the next lower class of qualification
c. Pass a criminal records check
d. Pass both a written and oral examination
A
b. Hold the next lower class of qualification
13
Q
What is one of the two main purposes of the CSA B-52 code?
Select one:
a. The various classifications of buildings and occupancies are listed and described with examples of each classification given.
b. To promote uniform requirements among the provinces and territories
c. Terms and equipment relating to refrigeration and air conditioning equipment are defined.
d. 2, 4
A
b. To promote uniform requirements among the provinces and territories
14
Q
Definitions for terms such as “shift engineer,” “chief engineer” and “assistant engineer” may be found in:
Select one:
a. The Canadian Labour Code
b. ASME Code Section VIII
c. CSA B-51
d. The Power Engineers’ Regulations of a particular jurisdiction
A
d. The Power Engineers’ Regulations of a particular jurisdiction
15
Q
What code contains guidelines for the care and operation of heating boilers? Select one: a. ASME Section IV. b. ASME Section IX c. CSA B52. d. CSA B51. e. ASME Section VI.
A
e. ASME Section VI.
16
Q
Clear definitions for terms and equipment relating to refrigeration and air conditioning equipment are defined in the \_\_\_\_\_. Select one: a. CSA-B51 b. ASME Section I c. ASME Section VII d. CSA-B52
A
d. CSA-B52
17
Q
It much easier to have changes made to a \_\_\_\_\_ than it is to have changes made to an Act. Select one: a. Regulation b. Proclamation c. Bill d. Act
A
a. Regulation
18
Q
This group of members of jurisdictional bodies meets at least annually. Answering to the ACI, they ensure that all Power Engineer examinations meet the requirements set by the jurisdictional legislative bodies. Select one: a. ASME b. ANSI c. SOPEEC d. IPECC e. ACI
A
c. SOPEEC
19
Q
What does the term CSA stand for with respect to Power Engineering? Select one: a. Congressional Standards Agency b. Catalytic Site Analysis c. Canadian Security Agency d. Combustion Safety Authority e. Canadian Standards Association
A
e. Canadian Standards Association
20
Q
The Act has \_\_\_\_\_ which are pursuant to the enforcement of the Act. Select one: a. Laws b. Regulations c. Bills d. Edicts e. Proclamations
A
b. Regulations
21
Q
Which activity does not use steam?
Select one:
a. removing skin from potatoes
b. refrigeration systems
c. heavy oil recovery
d. computer chip manufacturing
A
d. computer chip manufacturing
22
Q
What ASME code contains Recommended Guidelines For The Care of Power Boilers? Select one: a. ASME Section VII. b. ASME Section VIII c. CSA B52. d. CSA B51. e. ASME Section I.
A
a. ASME Section VII.
23
Q
This group meets at least once a year on situations which they feel are important and relevant to Power Engineers and the fulfillment of their duties and responsibilities. Select one: a. IPECC b. ASME c. ANSI d. SOPEEC e. ACI
A
e. ACI
24
Q
In a power plant, the power engineer may function as a supervisor who directs others in the \_\_\_\_\_ operation on a shift. Select one: A. occasional careful B. Safe and efficient C. Shipping and receiving D. Administrative and co-operative
A
B. Safe and efficient
25
```
What code regulates power boilers used in locomotive service?
Select one:
a. ASME Section I.
b. ASME Section VII.
c. ASME B31.3.
d. CSA B52.
e. ASME Section IX
```
a. ASME Section I.
26
In general, all Acts will have the all of the following in common except:
Select one:
a. The requirement for, and the methods of, inspecting, testing and certifying qualified repair and supervisory personnel will be clearly set out by the Act
b. There will be a list of penalties, which could be levied for complying with the Act or Regulations
c. A listing of the Codes and standards that have been adopted for use
d. The responsibility and delegated authority of the Authorized Inspector, as well as the responsibilities of the owner or Chief Engineer of a plant where an inspection is being done, will all be clearly stated
b. There will be a list of penalties, which could be levied for complying with the Act or Regulations
27
```
In order to produce greater efficiency, higher boiler pressures were used. This led to _____ due to the employment of unqualified power plant operators.
Select one:
A. Serious accidents
B. Safer working conditions
C. Higher efficiency
D. Economic gains
```
A. Serious accidents
28
```
Unqualified individuals operating a power plant or pressure plant risk the _____ of the plant and the general public.
Select one:
A. Economy
B. Resources
C. Safety
D. Health
```
C. Safety
29
Power engineers are:
Select one:
A. Automatically Safety code officers in a power plant
B. Skilled workers who operate and maintain the equipment in a power plant
C. Qualified to perform any welding jobs in a power plant
D. Qualified to make design changes in a power plant
C. Qualified to perform any welding jobs in a power plant
30
```
The "Pressure Vessels" section of the B-51 code identifies pressure vessels and their installation, including pressure vessel inspection openings. This section also shows the design of cushion tanks, blow-off vessels, and the installation of:
Select one:
a. Boiler drums.
b. Blowdown tanks.
c. Dearators.
d. Hydropneumatic tanks
```
d. Hydropneumatic tanks
31
```
One of the national standards which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the:
Select one:
a. ASME Codes
b. NFPA Codes
c. ANSI Codes
d. CSA B51
```
d. CSA B51
32
The investigation of an accident involving a power plant:
Select one:
a. may be carried out by the Chief Inspector of the jurisdiction.
b. Is not specified in a jurisdictional Act or Regulation .
c. Is not of concern to the Chief Inspector
d. Is clearly outlined in the Engineer's Regulations
a. may be carried out by the Chief Inspector of the jurisdiction.
33
```
What code contains Rules For Construction of low-pressure hot water supply boilers?
Select one:
a. ASME Section IV.
b. ASME Section VIII.
c. ASME Section IX
d. CSA B51.
e. CSA B52.
```
a. ASME Section IV.
34
```
This regulation lists the requirements which must be met for anyone wishing to write an applicable jurisdictional examination.
Select one:
a. Pressure Equipment Safety Regulation
b. Pressure Equipment Exemption Order
c. Power Engineers Regulation
d. Pressure Welders Regulation
```
c. Power Engineers Regulation
35
```
The provinces and territories of Canada are referred to as
Select one:
a. Governments
b. Authorities
. Jurisdictions c
d. Bodies
```
. Jurisdictions c
36
The main purpose of the Boiler and Pressure Vessel Code is:
Select one:
a. The promotion of efficient combustion
b. To protect life and property
c. To promote efficient boiler operation
d. To promote qualified training for operators
b. To protect life and property
37
Committees that establish standards are composed primarily of which of the following elements?
Select one:
A. One independent safety and standardisation board
B. One government appointed standards board
C. Only multi-National power corporations
D. Only experts from the industry and government
E. Experts from the industry, professional and insurance groups and all levels of government
E. Experts from the industry, professional and insurance groups and all levels of government
38
```
The holder of a Certificate of Competency, the classification of which authorises him or her to act as a engineer, may sketch, construct, install, operate, repair, and give advice on all things pertaining to any _____ in which that person is employed.
Select one:
A. Fish plant
B. Hydro plant
C. Welding shop
D. Power plant
```
D. Power plant
39
```
Which of these is the "Boiler, Pressure Vessel and Pressure Piping Code" ?
Select one:
a. CSA B51
b. ASME BPV-PPC
c. CSA B52.
d. ASME Section I.
```
a. CSA B51
40
In general, all Acts will have the all of the following in common except:
Select one:
a. The purpose of the Act will always be included
b. The scope of the Act
c. A listing of the Codes and standards that have not been adopted for use
d. The designation of a Director or Administrator and a description of their various responsibilities
c. A listing of the Codes and standards that have not been adopted for use
41
```
One of the national legislative items which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the:
Select one:
a. NAFTA Codes
b. ASME Codes
c. NFPA Codes
d. CSA B52
e. ANSI Codes
```
d. CSA B52
42
```
The holder of a Certificate of Competency, the classification of which authorises him or her to act as a engineer, may sketch, construct, install, operate, repair, and give advice on all things pertaining to any _____ in which that person is employed.
Select one:
A. Hydro plant
B. Fish plant
C. Power plant
D. Welding shop
```
C. Power plant
43
Which of the following is required in order to progress to a higher certificate?
Select one:
A. Both education and the next lower level certificate
B. Experience and education
C. Hold the next lower level certificate only
D. Education, experience, the next lower level certificate, and pass SOPEEC examinations
D. Education, experience, the next lower level certificate, and pass SOPEEC examinations
44
```
In the early days, owners of power plants hired _____ workers, who started out doing manual labour and through acquired experience they were promoted to jobs with gradually increasing levels of skill.
Select one:
A. Highly educated
B. Unskilled
C. Trained
D. Qualified
```
B. Unskilled
45
Water expands approximately ________ times when converted to steam
Select one:
a. 10,000
b. 100
c. 6000
d. 1600
d. 1600
46
Definitions for terms such as “shift engineer,” “chief engineer” and “assistant engineer” may be found in:
Select one:
a. The Canadian Labour Code
b. ASME Code Section VIII
c. CSA B-51
d. The Power Engineers’ Regulations of a particular jurisdiction
d. The Power Engineers’ Regulations of a particular jurisdiction
47
```
The provinces and territories of Canada are referred to as
Select one:
a. Bodies
b. Governments
c. Jurisdictions
d. Authorities
```
c. Jurisdictions
48
```
The code that regulates mechanical refrigeration is the:
Select one:
a. ASME Section I
b. ASME Section IV
c. CSA B-51
d. CSA B-52
```
d. CSA B-52
49
```
The main or primary document which must be passed through the jurisdictional parliament is a/an:
Select one:
a. Edict
b. Act
c. Bill
d. Regulation
e. Proclamation
```
b. Act
50
```
`Which of these is the "Mechanical Refrigeration Code"?
Select one:
a. ASME Section I.
b. CSA B52.
c. CSA B51.
d. ASME MRC
```
b. CSA B52.
51
What is one of the two main purposes of the CSA B-52 code?
Select one:
a. To promote uniform requirements among the provinces and territories
b. Terms and equipment relating to refrigeration and air conditioning equipment are defined.
c. 2, 4
d. The various classifications of buildings and occupancies are listed and described with examples of each classification given.
a. To promote uniform requirements among the provinces and territories
52
```
This group recommends updates to the learning materials of each class of Power Engineer, and the criteria required to ensure a Power Engineer is properly qualified when a Certificate of Competency is issued.
Select one:
a. IPECC
b. ACI
c. SOPEEC
d. ASME
e. ANSI
```
a. IPECC
53
```
It much easier to have changes made to a _____ than it is to have changes made to an Act.
Select one:
a. Act
b. Regulation
c. Proclamation
d. Bill
```
b. Regulation
54
In general, all Acts will have the all of the following in common except:
Select one:
a. A listing of the Codes and standards that have not been adopted for use
b. The scope of the Act
c. The designation of a Director or Administrator and a description of their various responsibilities
d. The purpose of the Act will always be included
a. A listing of the Codes and standards that have not been adopted for use
55
```
In a power plant, the power engineer may function as a supervisor who directs others in the _____ operation on a shift.
Select one:
A. Administrative and co-operative
B. Shipping and receiving
C. Safe and efficient
D. occasional careful
```
C. Safe and efficient
56
A welder performance qualification test:
Select one:
a. Is a practical welding test
b. Must be completed immediately after the welder obtains a certificate of qualification.
c. Is only required by welders working on steel structures
d. Is only required once in a welder's career
a. Is a practical welding test
57
Committees that establish standards are composed primarily of which of the following elements?
Select one:
A. One independent safety and standardisation board
B. One government appointed standards board
C. Only experts from the industry and government
D. Only multi-National power corporations
E. Experts from the industry, professional and insurance groups and all levels of government
E. Experts from the industry, professional and insurance groups and all levels of government
58
```
What code contains Rules For Construction of Power Boilers?
Select one:
a. ASME Section I.
b. CSA B52.
c. CSA B51.
d. ASME Section VIII.
```
a. ASME Section I.
59
```
Clear definitions for terms and equipment relating to refrigeration and air conditioning equipment are defined in the _____.
Select one:
a. ASME Section VII
b. CSA-B52
c. ASME Section I
d. CSA-B51
```
b. CSA-B52
60
```
Which of these is the "Boiler, Pressure Vessel and Pressure Piping Code" ?
Select one:
a. CSA B51
b. ASME BPV-PPC
c. CSA B52.
d. ASME Section I.
```
a. CSA B51
61
The main purpose of the Boiler and Pressure Vessel Code is:
Select one:
a. The promotion of efficient combustion
b. To protect life and property
c. To promote efficient boiler operation
d. To promote qualified training for operators
b. To protect life and property
62
```
The code that regulates mechanical refrigeration is the:
Select one:
a. ASME Section I
b. ASME Section IV
c. CSA B-51
d. CSA B-52
```
d. CSA B-52
63
```
What code contains Rules For Construction of low-pressure hot water supply boilers?
Select one:
a. ASME Section IX
b. CSA B51.
c. CSA B52.
d. ASME Section IV.
e. ASME Section VIII.
```
d. ASME Section IV.
64
```
In the early days, owners of power plants hired _____ workers, who started out doing manual labour and through acquired experience they were promoted to jobs with gradually increasing levels of skill.
Select one:
A. Unskilled
B. Trained
C. Highly educated
D. Qualified
```
A. Unskilled
65
In general, all Acts will have the all of the following in common except:
Select one:
a. The requirement for, and the methods of, inspecting, testing and certifying qualified repair and supervisory personnel will be clearly set out by the Act
b. The responsibility and delegated authority of the Authorized Inspector, as well as the responsibilities of the owner or Chief Engineer of a plant where an inspection is being done, will all be clearly stated
c. There will be a list of penalties, which could be levied for complying with the Act or Regulations
d. A listing of the Codes and standards that have been adopted for use
c. There will be a list of penalties, which could be levied for complying with the Act or Regulations
66
```
An international code which has been adopted and is enforced by all jurisdictions is the:
Select one:
a. Act
b. ASME Code
c. CSA B52
d. CSA B51
```
b. ASME Code
67
```
This regulation lists the requirements which must be met for anyone wishing to write an applicable jurisdictional examination.
Select one:
a. Power Engineers Regulation
b. Pressure Welders Regulation
c. Pressure Equipment Safety Regulation
d. Pressure Equipment Exemption Order
```
a. Power Engineers Regulation
68
```
This group meets at least once a year on situations which they feel are important and relevant to Power Engineers and the fulfillment of their duties and responsibilities.
Select one:
a. SOPEEC
b. ANSI
c. IPECC
d. ACI
e. ASME
```
d. ACI
69
```
What code regulates power boilers used in locomotive service?
Select one:
a. ASME Section I.
b. ASME B31.3.
c. ASME Section VII.
d. CSA B52.
e. ASME Section IX
```
a. ASME Section I.
70
```
The "Pressure Vessels" section of the B-51 code identifies pressure vessels and their installation, including pressure vessel inspection openings. This section also shows the design of cushion tanks, blow-off vessels, and the installation of:
Select one:
a. Blowdown tanks.
b. Dearators.
c. Boiler drums.
d. Hydropneumatic tanks
```
d. Hydropneumatic tanks
71
```
Unqualified individuals operating a power plant or pressure plant risk the _____ of the plant and the general public.
Select one:
A. Economy
B. Health
C. Safety
D. Resources
```
C. Safety
72
When applying to write a Power Engineer certificate of competency examination, the candidate must:
Select one:
a. Undergo mandatory drug testing
b. Hold the next lower class of qualification
c. Pass a criminal records check
d. Pass both a written and oral examination
b. Hold the next lower class of qualification
73
```
The Act has _____ which are pursuant to the enforcement of the Act.
Select one:
a. Laws
b. Proclamations
c. Regulations
d. Edicts
e. Bills
```
c. Regulations
74
```
What code contains guidelines for the care and operation of heating boilers?
Select one:
a. CSA B52.
b. ASME Section VI.
c. CSA B51.
d. ASME Section IV.
e. ASME Section IX
```
b. ASME Section VI.
75
Which activity does not use steam?
Select one:
a. heavy oil recovery
b. refrigeration systems
c. removing skin from potatoes
d. computer chip manufacturing
d. computer chip manufacturing
76
Which of the following is required in order to progress to a higher certificate?
Select one:
A. Education, experience, the next lower level certificate, and pass SOPEEC examinations
B. Hold the next lower level certificate only
C. Experience and education
D. Both education and the next lower level certificate
A. Education, experience, the next lower level certificate, and pass SOPEEC examinations
77
```
This group of members of jurisdictional bodies meets at least annually. Answering to the ACI, they ensure that all Power Engineer examinations meet the requirements set by the jurisdictional legislative bodies.
Select one:
a. IPECC
b. ASME
c. SOPEEC
d. ANSI
e. ACI
```
c. SOPEEC
78
Power engineers are:
Select one:
A. Qualified to perform any welding jobs in a power plant
B. Qualified to make design changes in a power plant
C. Skilled workers who operate and maintain the equipment in a power plant
D. Automatically Safety code officers in a power plant
C. Skilled workers who operate and maintain the equipment in a power plant
79
To register a boiler, pressure vessel, a pressure piping system, or a boiler fitting, within one of the provincial jurisdictions,
Select one:
a. The chief inspector of the jurisdiction must review and approve the design drawings and calculations
b. Drawings must be submitted to the ASME
c. The manufacturer need not have a quality control program in place
d. The CSA must approve the design
a. The chief inspector of the jurisdiction must review and approve the design drawings and calculations
80
The investigation of an accident involving a power plant:
Select one:
a. may be carried out by the Chief Inspector of the jurisdiction.
b. Is not specified in a jurisdictional Act or Regulation .
c. Is not of concern to the Chief Inspector
d. Is clearly outlined in the Engineer's Regulations
a. may be carried out by the Chief Inspector of the jurisdiction.
