202 ab review Flashcards
(32 cards)
What safety device is used on a shielding gas cylinder?
A. plastic rupture disc
B. metal rupture disc
C. plastic fusible plug
D. metal fusible plug
B. metal rupture disc
Which gas will be formed by the reaction between GTAW ultraviolet light and air?
A. CO (carbon monoxide)
B. CO 2 (carbon dioxide)
C. O 3 (ozone)
D. SO 2 (sulphur dioxide)
C. O 3 (ozone)
Which safety precaution should be taken to avoid accidental arcing of tungsten electrode when not in use?
A. torch should be wrapped and hung on insulated holder
B. disconnect ground
C. turn power source off
D. turn gas valve off
C. turn power source off
By keeping the end of the gas nozzle clean and uniform, what will it help to avoid?
A. a retarded gas flow
B. turbulence in the gas flow
C. arc hunting across the puddle
D. undercutting at bead edges
B. turbulence in the gas flow
Voltage is the pressure needed to push the amperage through the conductor:
A. True
B. False
A. True
Which is an advantage of GTAW spot welding?
A. it reduces distortion
B. no power source is required
C. crater cracking is not a problem
D. all of the above
A. it reduces distortion
Which type of AC welding machine feature provides a stable arc for welding aluminum?
A. Balance wave control
B. Pulsed high voltage injection
C. High frequency
D. All of the above
D. All of the above
When does high amperage GTAW have an advantage?
A. high deposition rates are required
B. welding root passes on carbon steel pipe
C. welding fill passes on carbon steel pipe
D. position welding on carbon steel pipe
B. welding root passes on carbon steel pipe
What is one responsibility of a”torch cap” that is used on a GTAW torch?
A. avoid accidental arcing
B. prevent amperage loss
C. keep the torch cleaned and cool
D. control electrode contamination
A. avoid accidental arcing
Gas nozzles for GTAW are numbered according to which dimension?
A. overall length
B. outside diameter
C. inside diameter
D. maximum amperage x 100
C. inside diameter
What shade of flash glasses would be suitable when in an area used for GTAW?
A. 2
B. 4
C. 8
D. 10
A. 2
What will happen to a GTAW torch that is too small for the current used?
A. it will overheat the electrode
B. it will overheat the torch body
C. it will overheat the power source
D. it will overheat the ceramic nozzle
B. it will overheat the torch body
What is the rate of pulsation when welding with high frequency pulse GTAW?
A. 25 to 100 times per second
B. 50 to 100 times per second
C. 100 to 400 times per second
D. 200 to 500 times per second
D. 200 to 500 times per second
Which design of consumable insert would be used on a Vee or U groove?
A. rectangular
B. J
C. K
D. inverted T
D. inverted T
Consumable inserts meet which AWS specification?
A. 5.18
B. 5.2
C. 5.28
D. 5.30
D. 5.30
Which of the following is a disadvantage of using hydrogen as a shielding gas for GTAW of carbon steel?
A. causes embrittlement
B. under cuts bead sidewalls
C. tends to oxidize
D. deteriorates tungsten
A. causes embrittlement
What may tungsten be alloyed with when used for GTAW?
A. cerium oxide
B. thorium oxide
C. zirconium oxide
D. all of the above
D. all of the above
Which of the following would be a good selection for a green coded electrode?
A. D.C. reverse polarity on mild steel
B. D.C. straight polarity on magnesium
C. A.C. high frequency start on stainless steel
D. A.C. continuous high frequency on aluminum
D. A.C. continuous high frequency on aluminum
What is one method used to prepare GTAW electrodes?
A. chemically
B. filing
C. oxy fuel torch
D. emery cloth
A. chemically
In the AWS designation ER 309, what does the “R” represent?
A. round
B. rod
C. rated
D. registered
B. rod
What is the color code for a EWP GTAW electrode?
A. red
B. green
C. yellow
D. brown
B. green
When welding with GTAW which factor does NOT affect weld position?
A. tensile strength
B. wire diameter
C. shielding gas
D. joint design
A. tensile strength