Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

4th Year Millwright > Mechanical Seals, Compression Packing and Valves > Flashcards

Mechanical Seals, Compression Packing and Valves Flashcards

1
Q

Why are mechanical seals not to be used in fires safety?

A

when a mechanical seal fails it fails completely

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What are the 4 basic types of components mechanical seals are made up of?

A

a set of primary sealing faces (rings), a mechanism for holding the seal faces together (ex: springs), a set of secondary seals, metal components

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Where is the primary sealing point on a mechanical seal?

A

between the stationary face and the rotating face

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What are the factors that govern the amount of friction between the sealing faces in a mechanical seal?

A

seal ring material, smoothness and flatness of the seal faces, the amount of closing force

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What feature does a unidirectional gas seal have that keeps the mating faces from coming into contact while running? What is the typical gap produced in these seals?

A

One of the faces has gas grooves only a few microns deep machined into it. The typical gap would be 0.0001ā€ to 0.0002ā€

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

In an emergency, what can the seal faces in a mechanical seal be hand-lapped and polished to?

A

three light bands

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What are the different types of secondary seals that can be used on a mechanical seal?

A

O-rings, PTFE wedges, V-rings, U-cups

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What secondary seal can only take pressure in one direction, and is not tolerant of any misalignment and axial movement.

A

PTFE wedges

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What secondary seals are normally used in sets of 3 or more?

A

V-rings (chevron seals)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is used with a U-cup seal to keep it loaded?

A

an energizer/spreader ring

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What type of seal has a secondary seal that is pushed back and forth axially to maintain constant contact at the seal faces?

A

pusher seal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is the major disadvantage of a multiple spring closing mechanism?

A

tendency to clog at the spring pockets

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What type of seal has a static secondary seal, and is inherently hydraulically balanced?

A

non-pusher (bellows) type seal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What are the 3 materials commonly used for the bellows in non-pushers seals?

A

rubber (elastomer), PTFE, welded metal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What type of pumped medium would a friction drive not be used with?

A

any lubricating medium (ex: oil)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What system has a fluid that is introduced at a higher pressure than that of the pumped medium?

A

barrier system

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Where would quenching fluids be introduced?

A

to the low-pressure side of the double seals

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

What is normally recommended when steam is used for quenching?

A

throttle bushing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What type of contamination control is used when there is a constant introduction of particles into the system?

A

cyclone seperator

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

What is the maximum seal chamber pressure for an unbalanced seal?

A

300 psi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What seals would be used when shaft speeds exceed 4500 ft/min?

A

stationary seals

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

What seal setup is recommended when the stuffing box is too small, and/or the product is very corrosive?

A

Outside mounted single seal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

What pressures can an unbalanced single outside mechanical seal handle? A balanced?

A

15-75 psi, 400 psi

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

What would a double mechanical seal arrangement be used for?

A

non-lubricated products, carcinogenic products, toxic products, hazardous fluids

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

What are the two types of double mechanical seal arrangements?

A

face-to-face, back-to-back

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

At what pressure is barrier fluid recommended to be at in relation the fluid pressure on the inner seal?

A

approx. 10% higher (min. 25 psi difference)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

When is a face-to-face arrangement used, and when does it act the same as a tandem seal?

A

When the stuffing box is too small to accommodate a back-to-back seal, acts the same as a tandem seal when the fluid pressure in the seal chamber is lower (buffer fluid) than that of the product as opposed to higher (barrier fluid)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

What are tandem seals also known as?

A

environmental seals

29
Q

What is one light band equal to?

A

11.6 millionths of an inch

30
Q

What tools would you use to check a seal face for flatness?

A

optical flat, monochromatic light

31
Q

What are some important points to remember when handling mechanical seals?

A

do not lube faces, keep hands clean when handling seals

32
Q

What would a wide track pattern on a seal face indicate? What about a narrow track pattern?

A

pump misalignment, overpressurizing

33
Q

What are the two types of closing mechanisms found on pusher seal?

A

single springs, multiple springs

34
Q

What are 4 reasons for providing flushing fluid?

A

lubrication, cooling, heating, cleansing

35
Q

How many light bands would seals be lapped to from the manufacturer?

A

1-3

36
Q

How many drops per minute must leak from compression packing?

A

40-60

37
Q

What type of fluid would a tandem seal use?

A

buffer fluid

38
Q

What type of non-pusher seal (bellows) would be good for high pressures?

A

the welded metallic type

39
Q

What is the purpose of compression packing?

A

to control leakage along moving parts

40
Q

In what application would compression packing be set to allow no leakage?

A

on a valve stem, also acts as a bearing in this case

41
Q

What are 3 types of motion compression packing may have to seal against?

A

rotary, reciprocating, helical

42
Q

What are the 3 types of automatic packing? What material are they normally made of?

A

cup packing, u-cup packing, v-cup packing, normally some kind of elastomeric

43
Q

Why is it important not to over-tighten jam packing?

A

The increase in friction between moving parts will act as a brake.

44
Q

Which way is automatic packing orientated in relation to the pressure its sealing against?

A

the lips face the pressure

45
Q

What jam packing type is the best for high pressures?

A

interlocking braid

46
Q

What packing component is installed in the stuffing box to aid in lubricating, sealing, flushing, and cooling?

A

a lantern ring

47
Q

Where does a lantern ring need to be located when used for cooling and sealing?

A

under the seal water connection

48
Q

When should carbon yarn not be used as packing material?

A

in the presence of strong oxidizers

49
Q

What type of packing material is used extensively in the food industry, but is limited in temperature and shaft speed?

A

PTFE fibre

50
Q

What are some causes of premature packing failure?

A

wrong type or size of packing used, improper installation, exposed to excessive heat

51
Q

Where does most of the wear on a pump shaft occur within the stuffing box?

A

On the outermost part of the shaft in contact with the packing.

52
Q

What are 3 metals commonly used in metallic compression packing?

A

Babbitt, aluminium, annealed soft copper

53
Q

What does the ā€œSā€ preceded by a number indicate on a valve?

A

the steam rating of the valve

54
Q

What does WOG indicate on a valve?

A

water, oil, and gas rating

55
Q

What are gate valves not used for and why?

A

Throttling, because wire drawing (erosion) can occur on the gate and the gate seats.

56
Q

Why is an accurate alignment important during installation of a butterfly valve?

A

to prevent binding of the pivoting disc

57
Q

What valve is used for precise fluid flow control?

A

needle valve

58
Q

What does a globe valve work well for?

A

throttling or regulating flow

59
Q

What valve operates the same as a standard globe valve but has reduce turbulence, flow restriction and pressure drop? When is it used?

A

angle valve, used when a 90 deg change is needed in a pipeline

60
Q

What type of valve would be used for throttling when handling corrosive and toxic fluids?

A

diaphragm valve

61
Q

What is the function of a pressure relief valve?

A

to prevent equipment damage

62
Q

What is the difference between the cracking pressure and pressure required to fully open a pressure relief valve called?

A

pressure override

63
Q

Name the different categories of valve actuators:

A

manual, power, pneumatic, hydraulic, electric, variable position

64
Q

When would you not apply oil or grease to a valve?

A

when the valve is in oxygen service

65
Q

What can be installed and adjusted to greatly reduce the mechanical stresses on a valve?

A

pipe hangers

66
Q

What are the hazards you may encounter when working on valves?

A

high pressures, high temperatures, reactive agents, flammable liquids or gases, poisonous substances

67
Q

What should be done to the splits on new packing when installing?

A

they should be staggered

68
Q

What is the purpose of a balance valve?

A

smaller actuators may be used to operate the valve because less force is required

4th Year Millwright (11 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions