Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

A Level Physics OCR B > 3: Sensing > Flashcards

3: Sensing Flashcards

1
Q

Describe an electronic sensor

A

Any change in the sensor’s detecting will change the current in the connected circuit. The current is processed to give you a reading

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is current?

A

The rate of flow of charge

Like the rate of flow of water in a pipe

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Describe conventional current and electron flow

A

Conventional: Flows from positive to negative terminal of a power supply.
Electrons are negatively charged and flow from negative to positive terminals - so conventional current is in the opposite direction to electron flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is potential difference?

A

The energy converted per unit charge moved - to make electric charge flow through a conductor you need to do work on it
(Like the pressure forcing water through the pipe)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Do you connect a voltmeter in parallel or series. Why?

A

Parallel because the p.d across components in parallel is the same

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What is power?

A

The rate of transfer of energy (the rate of work done)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

If you put a p.d across an electrical component….

A

A current will flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is resistance?

A

A measure of how difficult it is to get a current to flow through a component

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

How can you reduce the power dissipated during transmission of mains electricity?

A

P=IV

Mains electricity is transmitted at a high voltage and low current to minimise the power dissipated

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What does the term ‘I-V characteristic’ mean?

A

Refers to a graph which shows how the current flowing though a component changes as the p.d across it is increased

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The shallower the gradient of a characteristic I-V graph, the [ ] the resistance of the compoenent

A

Greater

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What does a curved line on an I-V graph mean?

A

Resistance of the component changes with the p.d across it

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

How can you investigate the I-V characteristic of a component using a test circuit?

A

1) Use a variable resistor to alter the p.d across the component and the current flowing through it, record V and I
2) Plot a graph of current against p.d difference from your results. This graph is the I-V characteristic of the component

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

If a conductor obeys Ohm’s Law what it it called?

A

An Ohmic conductor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What is Ohm’s Law?

A

Provided the external factor such as temperature are constant, the current through an ohmic conductor is directly proportional to the p.d across it (V=IR)
The gradient of the IV graph is constant (so resistance is constant) and the graph goes through the origin

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Describe the I-V characteristic of a filament lamp

Why is it this shape?

A

A curve, which starts steep but then gets shallower as the p.d rises
Current flowing though the lamp increases its temperature, so its resistance increases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Draw the I-V characteristic and circuit symbol for a filament lamp

A

Symbol: Cross in a circle
Graph: In 1st quadrant - steep then flat (like y = √x) and opposite of that in 3rd quadrant

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

Describe the relationship between a thermistor’s resistance and temperature

A

As the temperature increases the resistance decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

What is the circuit symbol for a thermistor?

And what is the I-V characteristic?

A

Resistor symbol with a line going diagonally across it

1st quadrant: curve where the gradient increases. The 3rd quadrant is the opposite

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Why can thermistors be used as temperature sensors?

A

A thermistor is a resistor with a resistance that depends on its temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

What type of thermistor do we look at?

A

NTC negative temperature coefficient, as the temperature increases the resistance decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Why does the resistance of a thermistor decrease as the temperature increases?

A

Increasing the current through the thermistor increases the temperature. As the thermistor heats up, the resistance decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Describe an LDR and its circuit symbol

A

Light dependent resistor, sensitive to light
The more light falls on it, the lower the resistance
Symbol: resistor in a circle with 2 arrows outside the circle, pointing towards centre of circle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

Describe diodes

A

They are designed to let current flow in one direction only

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q

What does forward bias mean when talking about diodes?

A

The direction in which the current is allowed to flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q

Most diodes require a [ ] voltage of about 0.6 V in the [ ] direction before they will conduct

A

Threshold

Forward

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q

What happens in reverse bias with diodes?

A

The resistance of the diode is very high and the current that flows is very tiny

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q

Describe the circuit symbol of a diode and a LED

A

A diode is a triangle, side on with a vertical line touching the point on the right, in a circle
A LED is a diode with 2 arrows pointing away from the circle, outside the circle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q

Describe the IV characteristic of a diode

A

Slightly negative current before threshold voltage where the current increases in a rough straight line

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q

What does the resistance of a length of wire depend on? Explain each one

A

1) Length. The longer the wire, the more difficult it is to make a current flow
2) Area. The wider the wire, the easier it will be for the electrons to pass along it
3) Resistivity. This depends on the material the wire’s made from, as the structure of the material may make it easy or difficult for charge to flow. Resistivity also depends on external factors like temperature

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q

This experiment finds the ‘X’ of a wire:
Measure the cross sectional area of a wire
Clamp the wire to a ruler with the circuit attached to the wire and attach flying leads to wire
Record length of the wire, the voltmeter reading, and the ammeter reading
Calculate the resistance

What is X?? How do you calculate X, given this data? How do you make the experiment more accurate?

A

X = resistivity

Repeat this measurement and calculate an average resistance for the length
Repeat with several different lengths
Plot your results on a graph of R against L, and draw a line of best fit
Multiply the gradient by the area to get Resistivity

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q

Explain how to find the cross sectional area of a wire

A

Assume the wire is cylindrical, and so it’s cross section is circular
Use a micrometer to measure the diameter of the wire in at least 3 different points along its length. Take an average value of the diameter and divide by 2 to get the radius

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q

What it a flying lead? (Used when investigating Resistivity)

A

The lead is a wire with a crocodile clip at the end to allow connection to any point along the test wire

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q

When calculating the Resistivity of a wire, does it matter that other components in the circuit have resistance?

A

No, the gradient of the line of best fit (R against L) isn’t affected by the resistance within the rest of the circuit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q

Describe the affect of temperature on the experiment to find Resistivity. What do you do in the experiment to mitigate this?

A

The Resistivity of a material depends on its temperature, so you can only find the Resistivity of a material at a certain temperature
Current flowing in the test wire can cause its temperature to increase, so you need to try and keep the temperature of the wire constant, eg. By only having small currents flow through the wire

36
Q

How can you find the conductivity of a wire using the experiment to find Resistivity?

A

σ = 1/ρ so just use the same data

37
Q

What affects how conductive a material is?

A

It’s number density of mobile charge carriers - the number of free electrons (or ions that are free to move) there are per cubic metre of the material. The more mobile charge carriers a material has per unit volume, the better a conductor it will be

38
Q

What are the charge carriers in metals?

A

Free electrons

39
Q

Why are metals good conductors?

A

They have loads of free electrons (charge carriers). The number density of mobile charge carriers is high

40
Q

Explain how a metal’s conductivity is affected by temperature

A

If you increase the temperature of a metal, the number of mobile charge carriers stays about the same.
As the electrons move, they scatter from the metallic lattice
As the temperature increases the lattice vibrates more, increasing the electron scattering, so the electrons are slightly less free to move
This means that as the temperature increases, the conductivity of a metal will slightly decrease

41
Q

What are the charge carriers in semiconductors?

A

Free electrons

42
Q

Compare the density of charge carriers of metals and semiconductors

A

Semiconductors have a much lower charge carrier number density (fewer free electrons) than metals, so they have a lower conductivity

43
Q

Explain how temperature effects the conductivity of a semiconductor

A

As you increase the temperature, more electrons are freed to conduct. This means that as the temperature increases, the conductivity of a semiconductor rapidly increases
Just as in metals, the semiconductor atom lattice will also vibrate more, scattering the free electrons as they move, but its effect is much smaller than the effect of the huge in increase in charge carriers

44
Q

What are thermistors and LDRs made out of? What does this mean about their conductivity?

A

Semiconductors
In thermistors, as temperature increases the conductivity rapidly increases, just like a semiconductor
In LDRs there are semiconductors whose conductivity is mostly controlled by light rather than heart, their conductivity increases with increasing light levels.

45
Q

Describe the mobile charge carriers in an insulator

A

A Perfect insulator wouldn’t have any mobile charge carriers, so it wouldn’t be able to conduct at all

46
Q

Resistance comes from [ ] colliding with [ ] and losing their [ ] to other forms

A

Electrons
Atoms
Energy

47
Q

Why do batteries have resistance? What is it called?

A

In a battery, chemical energy is used to make electrons move. As they move, they collide with atoms inside the battery.
Internal resistance

48
Q

[ ] is what causes batteries and cells to warm up when they’re used

A

Internal resistance

49
Q

What is load resistance?

A

The total resistance of all the components in the external circuit. Also called external Resistance

50
Q

What produces electrical energy in the battery?

A

Chemical reactions

51
Q

What is e.m.f?

A

The amount of electrical energy the battery produces for each coulomb of charge

52
Q

What is the terminal p.d?

A

The potential difference across the load resistance. It is the energy transferred when one coulomb of charge flows through the load resistance

53
Q

What would happen if there was no internal resistance in the battery?

A

The terminal p.d would be the same as the e.m.f. However in real power supplies, there’s always some energy lost, as heat energy, overcoming the internal resistance

54
Q

What are lost volts?

A

The energy wasted per coulomb overcoming the internal resistance

55
Q

Energy per coulomb supplied by the source = energy per coulomb transferred in load resistance + [ ]

A

Energy per coulomb wasted in internal resistance

56
Q

How do you find the total emf of two cells in series pointing in different directions?

A

Subtract emf of the one in the opposite directions

57
Q

Why are all emfs in parallel equal?

A

The current will split equally between identical cells. The charge only gains emf from the cells it travel through - so the overall emf in the circuit doesn’t increase

58
Q

How can you investigate internal resistance and emf?

A

1) Vary the current in the circuit by changing the value of the load resistance using the variable resistor
2) Measure the p.d for several different values of current
3) Record the data for V and I, and plot the results in a graph of V against I, then calculate emf and internal resistance

59
Q

Describe the circuit needed to investigate emf and internal resistance

A

Cell (made up of a cell and resistor) in series with a ammeter, voltmeter and switch (each on one side of a square with the cell at the top, and the others in order going clockwise)
Then in parallel with the voltmeter, a variable resistor
Pg 35

60
Q

How can you calculate emf and internal resistance from a V against I graph?

A

Start with V = ε - Ir
Since ε and r are constants, this is an equation of a straight line.
So the intercept with the vertical axis is ε
And the gradient is -r

61
Q

Why is it hard to choose the value for the load resistance, when investigating emf and internal resistance?

A

A low load resistance will give a large current, which will reduce the percentage uncertainty in the ammeter reading of the current.
But large currents will cause significant heating in the wires, which will invalidate your results

62
Q

What assumption fo you make in any experiment using voltmeters and ammeters?

A

You can assume that the voltmeter has a very high resistance, and the ammeter has a very low resistance

63
Q

Why does including a voltmeter in the circuit not affect the current through the variable resistor?
(Investigation of emf and internal resistance)

A

Voltmeters have a very high internal resistance, so the current through them is so low you can usually assume it is negligible

64
Q

Why does including an ammeter in the circuit not affect the current trough the variable resistor?
(Investigating emf and internal resistance)

A

The ammeter has a resistance that’s so low it’s negligible, and so the voltage across it is also negligible

65
Q

What is an easier way of measuring the emf of a power source?

A

Connect a voltmeter across its terminals.
The current through the voltmeters is assumed to be negligible and so any difference between your measurements and the emf will be so small that the difference isn’t usually significant

66
Q

When charge flows through a circuit, it is always [ ]

A

Conserved

67
Q

Whatever charge flows into a junction….

A

Will flow out again

68
Q

As current is rate of flow of [ ], it follows that whatever current flows into a junction is the same as the ….

A

Charge

Current flowing out of it

69
Q

What is Kirchhoff’s first law?

A

The total current entering a junction = the total current leaving it

70
Q

Describe the conservation of energy in a circuit

A

In electrical circuits, energy is transferred round the circuit. Energy transferred to a charge is emf, and energy transferred from a charge is potential difference

71
Q

What is Kirchhoff’s second law?

A

The total emf around a series circuit = the sum of the p.ds across each component

72
Q

Describe current, emf, and resistance in series circuits

A

Same current at all points of the circuit
Emf split between components. E = V₁ + V₂ etc.
R = R₁+ R₂ + R₃….
1/G = 1/G₁ + 1/G₂ + 1/G₃

73
Q

Describe current, voltage and resistance in a parallel circuit

A

Current is slept at each junction. I = I₁ + I₂ + …
Same p.d across all components
1/R = 1/R₁ = 1/R₂ = 1/R₃
G=G₁+G₂+G₃…

74
Q

What is the simplest potential divider?

A

A circuit with a voltage source and a couple of resistors in series

75
Q

How is the p.d split in a potential divider circuit?

A

The p.d of the voltage source is divided in the ratio of the resistances

76
Q

What can you use a potential divider circuit for?

A

Calibrating voltmeters, which have a very high resistance, because you can choose the resistances to get the voltage you want across one of them

77
Q

How can potential discovers be made into sensors?

A

By including components whose resistance changes with external factors, eg. LDRs and thermistors. This means Vₒᵤₜ varies with light or heat, so you can make a potential divider that works as a light or heat sensor
The circuit needs to be calibrated so you know how the voltage across the component and Vₒᵤₜ varies as external conditions change

78
Q

Describe the process of calibrating an electronic thermometer

A

1) measure the temperature of the water using the thermometer, and record the voltage across the resistor
2) Heat the beaker gently using the Bunsen burner, and record the temperature and the voltage at regular intervals
3) Plot a graph of temp. against voltage

79
Q

Describe the circuit needed to calibrate an electronic thermometers

A

A battery in series with a resistor and a NTC thermistor. With a voltmeter in parallel with the thermistor. The thermistor should be in a beaker of water, above a Bunsen burner

80
Q

What does a potentiometer do?

A

It uses a variable resistor to give variable voltage
It has a variable resistor replacing R1 and R2 of the potential divider, but it uses the same idea as a potential divider circuit

81
Q

How does a potentiometer work?

A

You move a slider or turn a knob to adjust the relative sizes of R1 and R2. That way you can vary V out (which is across R2) from 0V up to the input voltage, Vin

82
Q

Why are potentiometers very useful?

A

The voltage can be varied from 0 V to the input voltage

You can change a voltage continuously

83
Q

How do you reduce the effect of random errors when investigating the I-V characteristic of a component?

A

Repeat your measurements and take averages

84
Q

What can the I-V characteristic of a component tell you about the component?

A

Use it to see how the resistance changes (as the voltage/current increases/decreases)

85
Q

When investigating internal resistance and emf, how can you reduce the effect of heating the wires?

A

Include a switch in your circuit to turn off the current whenever possible to reduce the effect of heating in the wires on the resistance of the circuit

86
Q

Calibrating an electronic thermometer: How can you use the graph of temperature against voltage to calibrate the thermometer?

A

This graph is the thermistor’s calibration curve. You can use it to find the temperature of the thermistor from the voltage across it, without needing a thermometer - the thermistor and the calibration curve together are effectively another thermometer

87
Q

What is the equation linking current, the number of electrons, and the velocity of the electrons?

A 
I = nAve
I = current (A)
n = n. density of electrons (m⁻¹)
A = cross sectional area (m²)
v = drift velocity (ms⁻¹)
e = charge of an electron (C)

A Level Physics OCR B (61 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions