AFW Finished Flashcards by Danny W

Given the following plant conditions:
• The plant is at 100% power.
• The AFW control system is in a normal at-power lineup EXCEPT that P-8A AFW
Pump is out-of-service.
• “A” steam generator level lowers to 20% on all four safety channels.
What is the control mode of the AFW flow controllers from Aux Feedwater Pump P-8C
to both steam generators? (Assume no operator action.)
A. Automatic
B. Cascade
C. Manual
D. Program function

B. Cascade

How well did you know this?

Not at all

Perfectly

Which ONE of the following sets of valves will fail OPEN on a loss of Instrument Air?
A. Atmospheric Steam Dump Valves (CV-0779, 0780, 0781, & 0782).
B.Auxiliary Feedwater Control Valves (CV-0736A and CV-0737 A).
C. Pressurizer Spray Valves (CV-1057 & CV-1 059).
D. Auxiliary Feedwater Bypass Control Valves (CV-0736 and CV-0737).

B.Auxiliary Feedwater Control Valves (CV-0736A and CV-0737 A).

How well did you know this?

Not at all

Perfectly

Given the following plant conditions:
• The plant is at 100% power.
• P-8A, AFW Pp. is out of service.
• All other AFW system components are in a normal configuration.
• ‘A’ Steam Generator level lowers to 20% on all four safety channels.
What is the control mode of the AFW flow controllers from Aux Feedwater Pump, P-8C
to both steam generators? (Assume no operator action)
A. Automatic
B. Cascade
C. Manual
D. Program function

B~ Cascade

How well did you know this?

Not at all

Perfectly

Given the following:
• Plant is in Mode 3 with a cooldown to Mode 5 in progress
• Current S/G pressures are 800 psia
Which of the following AFW controllers can be used to establish AFW flow to the S/Gs
at flow rates at 70 gpm?
A. FIC-0736A/0737A (flow controllers from P-8C AFW Pump) if operated in auto or
manual mode.
B. FIC-0727/0749 (flow controllers from P-8A1B AFW pumps) if operated in auto or
manual mode.
C. FIC-0727/0749 (flow controllers from P-8A1B AFW pumps) if operated in PF mode
D. FIC-0736A/0737A (flow controllers from P-8C AFW Pump) if operated in PF mode

A. FIC-0736A/0737A (flow controllers from P-8C AFW Pump) if operated in auto or
manual mode.

How well did you know this?

Not at all

Perfectly

During a refueling outage the P-8C, Aux. Feedwater Pump is being used to add water
to the Steam Generators. While the P-8C Aux. Feedwater Pump is running, Instrument
Air is lost to both Discharge Flow Control Valves CV-0736A and CV-0737 A due to an
inadvertent isolation. How will the isolation of Instrument Air to CV-0736A and
CV-0737 A affect the Aux. Feedwater System?
A. CV-0736A and CV-0737 A will fail CLOSED.
B. CV-0736A and CV-0737 A will fail AS IS, due to N2 backup; when N2 backup is
depleted, valves will fail CLOSED.
C. CV-0736A and CV-0737A will fail AS IS, due to N2 backup; when N2 backup is
depleted, valves will fail OPEN.
D. CV-0736A and CV-0737 A will fail OPEN.

D. CV-0736A and CV-0737 A will fail OPEN.

How well did you know this?

Not at all

Perfectly

A plant power escalation is in progress.
The Main Feedwater Pump Speed controllers (HIC-0526/HIC-0529) are in MANUAL
speed control and the S/G Level Indicating Controllers (L1C-0701/L1C-0703) are in
AUTO.
Feedwater Control Mode Selector, HIC-0525, is in MANUAL.
Both Main Feed Pumps, P-1A and P-1B, are in service with Feed Pump speed at
approximately 3800 rpm each.
The output signal of L1C-0701 is 60% and the output signal of L1C-0703 is 62%.
What actions SHOULD the Operators take in order to transfer to CASCADE Speed
Control during the power escalation?
A. Place ‘A’ Feed Pump Speed Controller in CASCADE now and ‘B” Feed Pump
Speed Controller when L1C-0701 output is 62%
B. Place the Feed Pump Individual Speed Controllers in CASCADE now by pushing
the controller PF button.
C. Wait until the higher output signal from either L1C-0701 or L1C-0703 is
approximately 63 % before transferring.
D. Wait until the lower output signal from either L1C-0701 or L1C-0703 is approximately
63 % before transferring

C. Wait until the higher output signal from either L1C-0701 or L1C-0703 is
approximately 63 % before transferring.

How well did you know this?

Not at all

Perfectly

Which Auxiliary Feedwater System requirement addresses the concern for feedwater
line water hammer?
A. Minimum required flow for AFW pumps.
B. Upper limit on AFW pump motor amps.
C. Limits on reactor power level when adding relatively cold feedwaterfrom T-2,
Condensate Storage Tank.
D. Limits on S/G temperature and level when initiating flow through AFW Flow Control
Bypasses CV-0736/0737.

D. Limits on S/G temperature and level when initiating flow through AFW Flow Control
Bypasses CV-0736/0737.

How well did you know this?

Not at all

Perfectly

From full power, a Loss of All Offsite Power occurs. DIG 1-1 did not start
automatically, and will not start manually. Which Auxiliary Feedwater Pump(s) will be
operating 1 minute after an Auxiliary Feedwater Actuation Signal occurs? (Assume all
equipment functions as designed)
A. ONLY AFW Pump P-8A.
B. ONLY AFW Pump P-8B.
C. AFW Pumps P-8B and P-8C.
D. ONLY AFW Pump P-8C.

D. ONLY AFW Pump P-8C.

How well did you know this?

Not at all

Perfectly

Which ONE of the following describes the power supplies for P-8A and P-8C, Motor
Driven Aux. Feed Pumps? 
P-8A   P-8C
A.  Bus 1C  Bus 1E
B.  Bus 1C  Bus 1D
C.  Bus 1D  Bus 1C
D.  Bus 1E  Bus 1C

B. Bus 1C Bus 1D

How well did you know this?

Not at all

Perfectly

In addition to the performance of periodic surveillance tests, how is the control room
operator assured that all auxiliary feedwater pumps are ready to start?
A. “Ready” light on each pump’s controller is lit.
B. Breaker position lights for motor driven pumps - “ready” light on turbine driven
pump’s controller.
C. Breaker position lights for motor driven pumps - AO locally checks each shift for
turbine driven pump.
D. White status light for each pump lit.

C. Breaker position lights for motor driven pumps - AO locally checks each shift for
turbine driven pump

How well did you know this?

Not at all

Perfectly

What indication would the operators have in the Control Room that control of the AFW
flow controllers has been shifted from panel C-O1 to panel C-150?
A. AFW FIC-0727, 0749, 0736A, 0737A “PF” light is in “solid”.
B. The alarm “AFAS-FOGG SUBSYSTEM BYPASSED”, K-01 Window 38 alarms.
C. AFW FIC-0727, 0749, 0736A, 0737A “PF” light begins to blink.
D. The alarm “CONTROLS/INDICATION TRANSFERRED TO C 150/C 150A”, K-33
Window 40 alarms.

D. The alarm “CONTROLS/INDICATION TRANSFERRED TO C 150/C 150A”, K-33
Window 40 alarms.

How well did you know this?

Not at all

Perfectly

What indication is available in the Control Room for a low suction pressure trip of the
turbine driven Auxiliary Feedwater Pump P-8B, and what operation is required for
resetting the trip? (For resetting, assume that the low suction pressure condition has
been corrected.)
A. A shared alarm with P-8A provides indication of low suction pressure condition.
Reset by taking HS-0522B (K-8 Normal Steam Supply) to OPEN.
B. AMBER light above HS-0522B will illuminate to indicate low suction pressure
condition. Reset by taking HS-0552B to CLOSE.
C. AMBER light above HS-0522B will illuminate to indicate low suction pressure
condition. Reset by taking HS-0522B to OPEN.
D. A shared alarm with P-8A provides indication of low suction pressure condition.
Reset by taking HS-0522B to CLOSE.

D. A shared alarm with P-8A provides indication of low suction pressure condition.
Reset by taking HS-0522B to CLOSE

How well did you know this?

Not at all

Perfectly

Which of the following describes the locations where CV-0737 A, AFW from P-8C to
‘A’ S/G can be controlled?
A. Control Room and C-150
B. C-150 and Panel C-33
C. Control Room and Panel C-33
D. Control Room and locally in CCW Hx Room

C. Control Room and Panel C-33

How well did you know this?

Not at all

Perfectly

The Plant is at 100% power. Alarm EK-0140, “AUX FEEDWATER LOW SUCTION
PRESSURE,” trip is received and stays in. If the alarm is VALID, how does this alarm
affect the Auxiliary Feed System?
A. No effect since Auxiliary Feed Pumps are not running.
B. P-8A and P-8B and/or P-8C cannot be started depending upon which Low Suction
Pressure Trips are in.
C. P-8A, P-8B, and/or P-8C may not start on AFAS initiation, but all will start manually.
D. P-8A, P-8B, and P-8C will start on Loss of DC Power.

B. .P-8A and P-8B and/or P-8C cannot be started depending upon which Low Suction
Pressure Trips are in.

How well did you know this?

Not at all

Perfectly

Given the following conditions:
• From full power a transient occurs that results in a valid Aux. Feedwater
Actuation Signal (AFAS).
• P-8A Aux. Feed Pump is tagged out.
• Plant conditions also require a Natural Circulation plant cooldown.
• P-8C AFW Pump is the only AFW Pp. operating.
• AFW flow to “A” S/G = 80 gpm and stable.
• AFW flow to “B” S/G = 120 gpm and stable.
Which one of the following describes AFW System response in stablishing and
maintaining a natural circulation cooldown?
A.acceptable since Auxiliary Feedwater flow to at least ONE S/G is greater than 100
gpm.
B. acceptable since Auxiliary Feedwater flow to BOTH S/Gs is greater than 70 gpm.
C. NOT acceptable since P-8B turbine driven pump should have auto started due to
flow to ONE S/G at less than 100 gpm.
D. NOT acceptable since P-8B turbine driven pump should have auto started due to
flow to BOTH S/Gs at less than 165 gpm.

A’! acceptable since Auxiliary Feedwater flow to at least ONE S/G is greater than 100
gpm

How well did you know this?

Not at all

Perfectly

With the Plant at full power the control room receives EK-054B, “125V DC BUS
UNOERVOL TAGE/TROUBLE” along with several other alarms. Following a quick scan
of the panels the Reactor Operators report position indication for CV-051 0, S/G E-50A
MSIV has been lost and CV-2009, Cont Letdown Isolation has failed closed.
Which of the following is an additional condition that the operators should be able to
observe?
A. CV-13S9, Non-Critical Service Water Isolation failed closed
B. Auxiliary Feedwater P-8B in-service
C. Control Power to Bus 1Clost.
D Control Power to Bus 10 lost

B. Auxiliary Feedwater P-BB in-service

How well did you know this?

Not at all

Perfectly

From full power a transient occurs that results in a valid Aux. Feedwater Actuation
Signal (AFAS).
P-8A Aux. Feed Pump is tagged out.
Plant conditions also require a Natural Circulation plant cooldown.
P-8C AFW Pump is the ONLY AFW Pp. operating.
AFW flow to “All S/G = 80 gpm and stable.
AFW flow to IIBIIS/G = 120 gpm and stable.
Which one of the following describes AFW System response in establishing and
maintaining a natural circulation cooldown?
A.acceptable since Auxiliary Feedwater flow to at least ONE S/G is greater than 100
gpm.
B. acceptable since Auxiliary Feedwater flow to BOTH S/Gs is greater than 70 gpm.
C. NOT acceptable since P-8B turbine driven pump should have auto started due to
flow to ONE S/G at less than 100 gpm.
D. NOT acceptable since P-8B turbine driven pump should have auto started due to
flow to BOTH S/Gs at less than 165 gpm.

A.acceptable since Auxiliary Feedwater flow to at least ONE S/G is greater than 100
gpm.

How well did you know this?

Not at all

Perfectly

During a Loss of Main Feedwater the following plant conditions were observed.
Both S/G narrow range levels are 29%
Inverter #2 failed immediately prior to the Loss of Main Feedwater
Motor Driven Aux. FW. Pump P-8A is Out of Service for Maintenance
Which Aux. Feedwater pump(s) should be running, and if the normal Condensate
Storage Tank water supply were to become unavailable, what would their alternate
water source( s) be?
A. Both the Turbine Driven Aux. FW Pump P-8B with alternate water source from
Service Water, and the Motor Driven Aux. FW Pump P-8C with alternate water
source from Fire Protection should be running.
B. Only the Motor Driven Aux. FW Pump P-8C should be running with alternate water
source from Service Water.
C. Only the Turbine Driven Aux. FW Pump P-8B should be running with alternate
water source from Fire Protection/
D. Both the Turbine Driven Aux. FW Pump P-8B with alternate water source from Fire
Protection, and the Motor Driven Aux. FW Pump P-8C with alternate water source
from Service Water should be running.

C. Only the Turbine Driven Aux. FW Pump P-8B should be running with alternate
water source from Fire Protection/

How well did you know this?

Not at all

Perfectly

With the plant at 100% power, AFW Pump P-8B became inoperable. 72 hours have
transpired and a plant shutdown to MODE 3 was commenced. During the plant
shutdown the following occurred:
• Both Main Feed Pumps have tripped.
• Reactor automatically tripped on S/G low level
• The plant is currently in MODE 3.
• All 4 Primary Coolant Pumps are in service.
• Bus 1C de-energized concurrent with the reactor trip (overcurrent trip)
• AFW Pump P-8C is currently in-service
• S/G Pressures are 1000 psia.
For the above conditions, which one of the following describes the minimum action(s)
necessary for ensuring the AFW System will provide the required flow for adequate
core cooling?
A. No actions needed since the required flow will be met.
B. Secure all 4 Primary Coolant Pumps
C. Reduce S/G pressure to 900 psia and secure all 4 Primary Coolant Pumps
D. Reduce S/G pressure to 950 psia

NO IDEA

How well did you know this?

Not at all

Perfectly

During a normal plant shutdown:
• Both Main Feed Pumps have tripped.
• The plant is currently in MODE 3.
• All 4 Primary Coolant Pumps are in service.
• S/G Pressures are 1000 psia.
For the above conditions, which one of the following describes the minimum actions
necessary for ensuring the Auxiliary Feedwater System will provide the required flow
for adequate core cooling?
A. If using P-8A or P-8B, the required flow will be met. If using only P-8C, reduce S/G
pressure to = 900 psia or secure all 4 Primary Coolant Pumps.
B. If using P-8A or P-8B, reduce S/G pressure to = 900 psia. If using only P-8C,
reduce S/G pressure to = 900 psia or secure all 4 Primary Coolant Pumps.
C. If using P-8A or P-8B, the required flow will be met. If using only P-8C, reduce S/G
Pressure to = 900 psia and secure all 4 Primary Coolant Pumps.
D. If using P-8A or P-8B, reduce S/G pressure to = 900 psia. If using only P-8C,
reduce S/G pressure to = 900 psia and secure all 4 Primary Coolant Pumps.

A. If using P-8A or P-8B, the required flow will be met. If using only P-8C, reduce S/G
pressure to = 900 psia or secure all 4 Primary Coolant Pumps.

How well did you know this?

Not at all

Perfectly

Given the following conditions:
• A reactor trip from full power has occurred
• AFAS automatically actuated; P-8A, AFW Pump, automatically starts
• P-8C, AFW Pump is in AUTO
• AFAS has NOT been reset
Which one of the following sets of parameters will cause P-8C to automatically start?
A S/G Level B S/G Level A S/G Flow B S/G Flow
A.60% 59% 165 gpm 0gpm
B.28% 29% 165 gpm 90gpm
C.28% 29% 165 gpm 165 gpm
D.60% 55% 90gpm 0 gpm

D.60% 55% 90gpm 0 gpm

How well did you know this?

Not at all

Perfectly

Given the following conditions:
• An inadvertent Auxiliary Feedwater Actuation Signal (AFAS) has occurred.
• AFW Pumps P-8A and P-8C Start Select Handswitches are in MANUAL.
• CV-0522B, Auxiliary Feedwater (AFW) Pump P-8B Normal Steam Supply, is in
AUTO.
Which ONE of the following describes the response of CV-0522B to the AFAS?
A. Automatically opens immediately.
B. Automatically opens after a 30.5 second time delay.
C. Automatically opens after a 112.5 second time delay.
D. Must be opened by an Operator.

C’:’“Automatically opens after a 112.5 second time delay.

How well did you know this?

Not at all

Perfectly

AFW CKIO.O 003
Given the following plant conditions:
• The Plant was initially at full power.
• A transient caused a valid low S/G level.
• A valid AFAS has actuated.
• Aux Feedwater Pump P-8A is running and delivering 75 gpm flow to each steam
generator.
Aux Feedwater Pump P-8C will:
A. NOT START since adequate auxiliary feedwater flow is being provided to the steam
generators.
B. NOT START since P-8A is running with flow to at least one steam generator.
C. START but only recirc. back to T-2.
D. START and deliver flow to the S/Gs at 165 gpm each.

D~ START and deliver flow to the S/Gs at 165 gpm each.

How well did you know this?

Not at all

Perfectly

Given the following plant conditions:
• Suction pressure in the headers supplying water to the AFW pumps from the
Condensate Storage Tank (T-2) drops to 16 psia and remains at that pressure.
• All three AFW pumps were running before the drop in pressure.
Which ONE of the following describes the status of the AFW pumps after the pressure
drop?
A. All three pumps have tripped.
B. P-8B is still running, P-8A and P-8C have tripped.
C. All three pumps are still running.
D. P-8C is still running, P-8A and P-8B have tripped.

A’! All three pumps have tripped.

How well did you know this?

Not at all

Perfectly

``` Auxiliary Feedwater Pump P-8A will automatically trip on: A. low oil pressure. B. low suction pressure. C. overspeed. D. high discharge flow ```

B~ low suction pressure.

From full power, a Loss of All Offsite Power occurs. DIG 1-1 did not start automatically, and will not start manually. Which Auxiliary Feedwater Pump(s) will be operating 1 minute after an Auxiliary Feedwater Actuation Signal is received? (Assume all other equipment functions as designed) A. ONLY AFW Pump P-8A. B. ONLY AFW Pump P-8B. C. AFW Pumps P-8B and P-8C. D. ONLY AFW Pump P-8C.

D~ ONLY AFW Pump P-8C.

Which ONE of the following selections describes an effect on the Auxiliary Feedwater System if DC panel 011-1 is de-energized? A. Auxiliary Feed Pump P-8A would not be able to start on AFAS (Channel A). B. The AFAS trip on Channel A sensor cabinet will trip and cannot be BYPASSED. C. An AFAS Actuation signal will be generated on Channel B but no automatic actions will occur. D. Pump P-8C will not start due to a low suction pressure trip being generated.

A'I Auxiliary Feed Pump P-8A would not be able to start on AFAS (Channel A).

A valid AFW actuation (AFAS) signal is actuated. After several minutes, with no operator action, the control room operator notices that both P-8A and P-8C are running. What additional information can the operator derive from these indications? A. The system is operating properly and both steam generators are being fed by both pumps through a common header. B. P-8A was not delivering adequate flow to the steam generators within 30.5 seconds of receipt of the AFAS signal. C. P-8A control room handswitch was not in the AUTO position at the time the AFAS signal was received. D. P-8B is not operating correctly, because it should also be running.

B~ P-8A was not delivering adequate flow to the steam generators within 30.5 seconds of receipt of the AFAS signal

Given the following conditions: • The main flow through a pipe in a safety-related system at normal pressure is 100 gpm. • A vent valve on the pipe will allow 4 gpm if full open at normal pressure. • A drain valve on the pipe will allow 8 gpm if full open at normal pressure. Which of the following describes the procedural requirements for locking devices for these valves? VENT VALVE DRAIN VALVE A. Lock Required Lock Required B. Lock Required Lock not required C. Lock Not Required Lock Required D. Lock Not required Lock Not Required

D. Lock Not required Lock Not Required

``` Which ONE of the following results in an automatic trip of the P-8B auxiliary feedwater pump? A. Low oil pressure. B. High exhaust pressure. C. Low suction pressure. D. Condenser vacuum of 5" and less. ```

C. Low Suction Pressure

The following plant conditions exist: • A spurious turbine trip caused a reactor trip onehour ago. • EOP-1.0 was implemented and completed with all Acceptance Criteria satisfied. • AFAS automatically initiated on low Steam Generator level during EOP-1.0. • Auxiliary Feedwater Pump P-8A is in service delivering 165 gpm to each S/G. • AFAS is not reset • Both "A" S/G level and "B" S/G level are 65% and stable. What would be the plant response to placing the handswitch for Auxiliary Feedwater Pump P-8A to TRIP? A. Auxiliary Feedwater Pump P-8B will immediately start. B. Auxiliary Feedwater Pump P-8C will immediately start. C. Auxiliary Feedwater Pump P-8A will restart in approximately 3 seconds. D. Auxiliary Feedwater Pump P-8C will start in approximately 30 seconds.

D. Auxiliary Feedwater Pump P-8C will start in approximately 30 seconds

Given the following conditions: The plant is at full power when a Loss of All Offsite Power occurs. BOTH Diesel Generators have started and loads are sequencing. The Reactor trips, but the Main Turbine does NOT automatically trip. Steam Generator (S/G) levels quickly lower to approximately 10% before the NCO manually trips the Main Turbine. 30 seconds after manually tripping the Main Turbine the NCO notes that Auxiliary Feedwater (AFW) flow indicates 0 gpm to each S/G. What action, if any, is required, and why? A. No action is required, since AFW Pump P-8A will be sequenced on and deliver design flow to each S/G. B. The operator must manually initiate AFAS (Aux. Feed Actuation Signal) due to the Loss of Offsite Power. C. The operator must manually start AFW Pump P-8C since P-8A has failed to start on low Steam Generator level. D. No action is required since no power is available to motor driven AFW pumps and the turbine driven AFW pump will deliver design flow in 92 seconds.

A'I No action is required, since AFW Pump P-8A will be sequenced on and deliver design flow to each S/G.

Given the following conditions: • A reactor trip from full power occurred 50 minutes ago. • AFAS automatically actuated; P-8A is running and delivering 165 gpm to each S/G; P-8G is in AUTO. • "A" S/G level is 65%, "B" S/G level is 65%. What will be the effect on P-8G if flow to "A" S/G via FIG-0749 is manually reduced to 55 gpm and flow to "B" S/G via FIG-0727 is manually reduced to 55 gpm? A. Not start automatically since P-8A is running and total AFW flow is greater than the minimum required. B. Not start automatically since P-8A is running and AFW flow to each S/G is greater than the minimum required. G. Start automatically and recirculate flow to T-2 since total AFW flow is less than the minimum required. D. Start automatically and deliver flow to each S/G since AFW flow is less than the minimum required to each S/G.

D. Start automatically and deliver flow to each S/G since AFW flow is less than the minimum required to each S/G.

Given the following conditions: • A reactor trip from full power occurred 50 minutes ago. • AFAS automatically actuated; P-8A is running and delivering 165 gpm to each S/G; P-8C is in AUTO. • AFAS has NOT been reset. • 'A' S/G level is 65%; 'B' S/G level is 65%. What will be the effect on P-8C if flow to 'A' S/G via FIC-0749 is manually reduced to 110 gpm and flow to 'B' S/G via FIC-0727 is manually reduced to 110 gpm? A. Not start automatically since P-8A is running and S/G levels are both greater than 30%. B. Not start automatically since P-8A is running and AFW flow to each S/G is greater than the minimum required. C. Start automatically and recirculate flow to T-2 since total AFW flow is less than the minimum required. D. Start automatically and deliver flow to each S/G since AFW flow is less than the minimum required to each S/G.

B~ Not start automatically since P-8A is running and AFW flow to each S/G is greater than the minimum required.

The plant has experienced an inadvertent feedwater isolation signal requiring a Reactor Trip. S/G levels have fallen below 30%. The P-8A, Aux Feedwater Pump did not start as designed due to a breaker alignment problem. When is the P-8C, Aux Feedwater Pump designed to start and what is its power supply? A. P-8C starts immediately following the AFAS signal, and it is powered from Bus 1D B. P-8C starts immediately after P-8A fails to start, and it is powered from Bus 1C C. P-8C starts 30.5 sec following the AFAS signal, and it is powered from Bus 1D D. P-8C starts 112.5 see following the AFAS signal, and it is powered from Bus 1C

C~ P-8C starts 30.5 sec following the AFAS signal, and it is powered from Bus 1D

Given the following conditions: • Plant is at full power when a Loss of All Offsite Power occurs • Only DIG 1-2 starts and begins load sequencing. • Reactor trips, but the Main Turbine does NOT automatically trip. • S/G levels quickly lower to approximately 32% before the NCO manually trips the Main Turbine. • 30 seconds after manually tripping the Main Turbine the NCO notes that AFW flow indicates 0 gpm to each S/G. • A loss of Preferred AC Bus Y-20 occurred concurrent with the auto reactor trip. What action, if any, is required, and why? A. No action is required, since AFW Pump P-8C will start and deliver design flow to each S/G. B. The operator must manually initiate AFAS (Aux. Feed Actuation Signal) due to the Loss of Offsite Power. C. The operator must manually start AFW Pump P-8C since P-8B has failed to start on low S/G level. D. No action is required since both motor driven AFW pumps cannot be started and the turbine driven AFW pump will deliver design flow in 92 seconds

D~ No action is required since both motor driven AFW pumps cannot be started and the turbine driven AFW pump will deliver design flow in 92 seconds

Given the following conditions: • A plant heatup is in progress from a refueling outage • Plant is currently in Mode 3 at NOP/NOT • AFW Pump P-8A is operating in MANUAL supplying 165 gpm is each S/G • During Secondary side heatup using the MSIV Bypass Valves, a large steam leak occurs in the turbine building and both steam generators start to blow down uniformly. Which ONE (1) of the following describes the expected response of the AFW system to these events? A. AFW pump P-8B will start when either S/G level lowers to 27% NR B. AFW pumps P-8B and P-8C will start when either S/G level lowers to 27% NR C. The AFW system will not respond to these events D. AFW pump P-8C will start when either S/G level lowers to 27% NR

C'f" The AFW system will not respond to these events

Given the following conditions: • Plant is at 100% power. • Condensate Storage Tank temperture is 81°F. • Aux Feedwater System testing requires initiation of AFW flow to the Steam Generators (S/Gs). What is the operational concern for initiating AFW flow under these conditions? A. Could result in thermal shocking and cracking damage to the AFW piping inside the S/Gs. B.Adding cold water to the S/Gs may result in Reactor power rising above 100%. C. Due to the low differential pressure between pump discharge and S/G pressure, pump minimum flow requirements cannot be met. D. The resulting higher S/G levels will result in moisture carryover to the Main Turbine.

B~ Adding cold water to the S/Gs may result in Reactor power rising above 100%.

The MAXIMUM running amp limits for the motor-driven Auxiliary Feedwater Pumps ensures: A. the pumps will NOT be "dead-headed." B. the full-load motor heat will NOT be exceeded. C. bus power supply overcurrent protection is maintained. D. required work of the pumps during accident conditions are maintained within limits.

B:t the full-load motor heat will NOT be exceeded.

The Plant is in Mode 4 and a cooldown is in progress in preparation for a refueling outage. The Condensate Storage Tank (T-2) level has dropped to 27%. What action is required and what is the basis for the action? A. Level must be raised to the level prescribed by Tech Specs for T-2. B. Level must be restored immediately to clear the Low Suction Pressure trip for the auxiliary feedwater pumps. C. Portions of the Auxiliary Feedwater System must be vented and T-2 level restored to prevent air inleakage into the system. D. Portions of the Auxiliary Feedwater System must be vented and T-2 level restored to greater than 50% to clear the Low Suction Pressure trip for the auxiliary feedwater pumps.

C. Portions of the Auxiliary Feedwater System must be vented and T-2 level restored to prevent air inleakage into the system.

Erratic valve operation of CV-0736A, Auxiliary Feedwater Flow Control to E-50B, is avoided by ensuring that as: A. S/G pressure RISES, minimum required flow through the valve RISES. B. S/G pressure RISES, minimum required flow through the valve LOWERS. C. T-2, Condensate Storage Tank level LOWERS, minimum required flow through the valve LOWERS. D. T-2, Condensate Storage Tank level LOWERS, minimum required flow through the valve RISES.

B:-,S/G pressure RISES, minimum required flow through the valve LOWERS.

The Plant has tripped due to a Loss of Off-site power at 1300. Emergency DIG 1-1 will not start. Power control has been contacted and is unable to project when power will be restored to the switchyard. Assuming operators take all required actions which of the following design capacities will be the FIRST to be exceeded before power is restored? A. Diesel Generator Fuel oil inventory B. Condensate inventory C. Station Battery Voltage D. ADV Nitrogen backup supply

B. Condensate inventory

What indications are available that an Auxiliary Feed Pump low suction pressure trip has occurred for P-8A and P-8C? A. White indicating light on P-8A and P-8C breaker cubicles are lit. B. Amber indicating light on P-8A and P-8C breaker cubicles are 'OUT'. C. Amber indicating lights on P-8A and P-8C breaker cubicles and the low suction pressure trip annunciator "sealed in" on the K-01 alarm panel until the low suction pressure has been reset. D. Green 'PF' light 'ON' on FIC-0737A, FIC-0736A, FIC-0727 and FIC-0749 on the C-01 panel, with the "P-8A/B LO SUCTION TRIPPED" and "P-8C LO SUCTION TRIPPED" alarms in solid on the Auxiliary Feed Water status array scheme.

C~ Amber indicating lights on P-8A and P-8C breaker cubicles and the low suction pressure trip annunciator "sealed in" on the K-01 alarm panel until the low suction pressure has been reset.

The plant is operating at 55% power with one feed water pump in service when the following events occur: • The reactor trips. • At the time of the reactor trip the Y-1 0 inverter DC input breaker trips for an unknown reason. If NO operator actions are taken, which ONE of the following would be the correct response to the Auxiliary Feed Water System to this event? A. All three AFW pumps auto start feeding both steam generators. B. P-8B auto starts feeding both steam generators. C. P-8A and P-8C auto start feeding both steam generators. D.P-8A is capable of auto starting and feeding both steam generators.

D~ P-8A is capable of auto starting and feeding both steam generators.

Which ONE of the following statements ensures that enough water is available for 8 hours of Auxiliary Feedwater Pump operation (when PCS is> 300°F)? A. The levels of Condensate Storage Tank (T-2) must be maintained above 31% and Primary Makeup Tank (T-81) must be maintained above 68%. B. The levels of Condensate Storage Tank (T-2) must be maintained above 68% and Primary Makeup Tank (T-81) must be maintained above 83%. C. The levels of Condensate Storage Tank (T-2) must be maintained above 71% and Primary Makeup Tank (T-81) must be maintained above 83%. D. The levels of Demineralized Water Storage Tank (T-939) must be maintained above 52% and Primary Makeup Tank (T-81) must be maintained above 93%.

C. The levels of Condensate Storage Tank (T-2) must be maintained above 71% and Primary Makeup Tank (T-81) must be maintained above 83%

Due to an electical fault, Y-20 has been de-energized and isloated. Due to this fault: A. The 'A' channel AFAS actuation cabinet will not process an AFAS actuation signal. B. P-8B is the only pump that will start on receipt of an AFAS signal. C. The 'B' channel AFAS actuation cabinet will not process an AFAS actuation signal. D. P-8C cannot be started by AFAS or manually in the Control Room.

D. P-8C cannot be started by AFAS or manually in the Control Room

The Plant has tripped due to a Loss of Off-site power at 1300. Emergency DIG 1-1 will not start. Power control has been contacted and is unable to project when power will be restored to the switchyard. Assuming operators take all required actions which of the following design capacities will be the FIRST to be exceeded before power is restored? A Diesel Generator Fuel oil inventory B.Condensate inventory C. Station Battery Voltage D. ADV Nitrogen backup supply

B:I Condensate inventory

Which ONE of the following statements describes the automatic response of auxiliary feedwater pump P-8C to an AFAS signal? A. Will start after 2.5 seconds. B. Will start if P-8A and P-8B are not running after 112.5 seconds. Which ONE of the following statements describes the automatic response of auxiliary feedwater pump P-8C to an AFAS signal? A. Will start after 2.5 seconds. B. Will start if P-8A and P-8B are not running after 112.5 seconds. C. Will start if P-8A is not delivering flow after 30.5 seconds. D. Immediately starts on recirculation lineup; will shift to deliver flow to steam generators if flow is not sensed in 30.5 seconds D. Immediately starts on recirculation lineup; will shift to deliver flow to steam generators if flow is not sensed in 30.5 seconds

C~ Will start if P-8A is not delivering flow after 30.5 seconds.

Which ONE of the following statements describes a condition which would disable the P-8B Aux Feedwater Pump low suction pressure trip? A Loss of DC Panel 011-1. B. Loss of Preferred AC Bus Y-10. C. Control established from the Cold Shutdown Panel C-33. D. Loss of power to L1A--2021 and L1A-2022 (T-2 Hi-Lo)

A. Loss of DC Panel 011-1.

• A reactor trip from full power occurred 50 minutes ago. • AFAS automatically actuated. • Auxiliary Feedwater Pump P-8A is running and delivering 165 gpm to each S/G. • P-8C is in AUTO, and not running. • Auxiliary Feedwater Actuation Signal (AFAS) has NOT been reset. o 'A' S/G level is 68%, 'B' S/G level is 60%. Then, flow to 'A' S/G (via FIC-0749) is manually reduced to 90 gpm and flow to 'B' S/G (via FIC-0727) is manually reduced to 110 gpm. Which one of the following describes the expected response of AFW Pump P-8C, AND the reason for that response? A. Not start automatically, since P-8A is running and S/G levels are both greater than the minimum required. B.Not start automatically, since P-8A is running and AFW flow satisfies the minimum required. C. Start automatically, since one S/G level is outside of the normal band. D. Start automatically, since AFW flow is less than the minimum required.

B~ Not start automatically, since P-8A is running and AFW flow satisfies the minimum required.

Given the following conditions: • A reactor trip from full power occurred 15 minutes ago. • AFAS automatically actuated. • AFW Pump P-8A is running and delivering 165 gpm to each S/G. • P-8C is in AUTO, and not running. • 'A' S/G level is 38%, 'B' S/G level is 26%. Then, flow to 'A' S/G (via FIC-0749) is manually reduced to 90 gpm and flow to 'B' S/G (via FIC-0727) is manually reduced to 95 gpm. Which one of the following describes the expected response of AFW Pump P-8C, AND the reason for that response? A. Not start automatically, since P-8A is running and total AFW flow is above 165 gpm. B. Not start automatically, since P-8A is running and both S/G levels are greater than the AFAS setpoint. C. Start automatically, since one S/G level is outside of the normal band. D. Start automatically, since AFW flow is less than the minimum required.

D. Start automatically, since AFW flow is less than the minimum required

Given the following conditions: • The Auxiliary Feed Water system is NOT operating. • Preparations are being made to feed the SGs using the AFW Bypass Valves, CV-0736 and CV-0737. Prior to using these valves, S/G Temps must be (1) OR S/G Levels must be (2) (1) (2) A. 300F 212F

Given the following conditions: • The Control Room has been evacuated due to a fire in the Control Room. • Auxiliary Shutdown Panel C-150 has been placed in service. As a result of placing C-150 in service, AFW Pump P-8B: A. will NOT automatically trip on low suction pressure. B. will NOT be available as a source of feedwater. C. automatic speed control is disabled. D. overspeed trip protection is disabled.

A'! will NOT automatically trip on low suction pressure.

Given the following conditions: • P-88, Turbine Driven Aux. Feedwater Pump, is the only available operating AFW Pump. • The Control Room has been evacuated due to a fire. Auxiliary Shutdown Panel C-150 is being placed in service. What will be the effect on the Auxiliary Feedwater components? A. Any valid low suction pressure trip of P-88 must be reset at C-150. B. P-88 will operate but the low suction pressure trip will not be available. C. AFW Control Valves, CV-0727 and CV-0749, must be locally controlled. D. CV-05228, Steam Supply to P-88, must be manually controlled locally.

B. P-88 will operate but the low suction pressure trip will not be available.

The plant is in Mode 3. AFW flow indicators FI-0727 and FI-0727 A have both been declared inoperable. Which of the following actions are required? A. Immediately declare AFW Pump P-8A inoperable. B.Immediately declare AFW Flow Control CV-0727 inoperable. C. Within 2 hours, determine the operability of P-8A. D. Within 2 hours, determine the operability of CV-0727.

B.Immediately declare AFW Flow Control CV-0727 inoperable.

The plant is at full power. Due to an accident during a construction project, the BACKUP suction piping to AFW Pump P-8C has been completely severed. Which ONE of the following actions is required? A. Immediately declare P-8C inoperable. B. After 7 days declare P-8C inoperable. C. Immediately commence actions to place the reactor in MODE 2 within 6 hours, MODE 3 within 12 hours, and MODE 4 within 36 hours. D. After 7 days commence actions to place the reactor in MODE 2 within 6 hours, MODE 3 within 12 hours, and MODE 4 within 36 hours.

D. After 7 days commence actions to place the reactor in MODE 2 within 6 hours, MODE 3 within 12 hours, and MODE 4 within 36 hours.

With the plant at 100% power ALL AFW pumps become inoperable. Which ONE of the following applies? A. Within 1 hour action should be initiated to shutdown the plant in accordance with LCO 3.0.3. B. At least one train of AFW must be restored to operable within 72 hours. C. Immediately initiate action to reduce to

D. Immediately initiate action to restore one AFW train to operable.

For the Auxiliary Feedwater System, which one of the following conditions requires entry into a Technical Specification Limiting Condition of Operation (LCO)? (Assume MODE 1 conditions.) A. T-2, Condensate Storage Tank, inventory is 63,500 gallons, and T-81, Primary Makeup Water, is 41,000 gallons. B. FIC-0737 A has been selected to AUTO. C. P-8B and P-8C are the only operable Aux. Feedwater Pumps. D. P-8C control handswitch HS-P-8C has been selected to the MANUAL position for 3 hours for surveillance testing.

C. P-8B and P-8C are the only operable Aux. Feedwater Pumps.

SRO ONLY) Following a Reactor Trip coincident with a Loss of Offsite Power, the combined usable volume of the Condensate Storage Tank (T-2) and Primary Makeup Storage Tank (T-81) shall be greater than or equal to 100,000 gallons. The basis for this is to provide the inventory to faciliate: A. two AFW pumps to operate 16 hours. B. two AFW pumps to operate 8 hours. C. one AFW pump to operate 16 hours. D. one AFW pump to operate 8 hours.

D. one AFW pump to operate 8 hours

During testing in preparation for a plant startup, P-8A, Auxiliary Feedwater Pump, Start Select handswitch is placed in "MANUAL." P-8C, Auxiliary Feedwater Pump, and P-8B, Auxiliary Feedwater Pump, are OPERABLE. Which one of the following describes the requirements for placing the P-8A Start Select switch in "AUTO?" P-8A Start Select switch must be placed in AUTO prior to .... A. entering MODE 4. B. entering MODE 3. C. PCS reaching 325 of D. entering MODE 2.

B~ entering MODE 3.

``` With the plant at 25% power, FIC-0727/0749, AFW Flow Controller is considered OPERABLE if it is in: A. MANUAL. B. PF Mode. C. AUTO. D. CASCADE. ```

Dt CASCADE.

During Hot Shutdown with Y-30 out-of-service, Y-10 Inverter AC output breaker trips for an unknown reason. After verifying the fault does not exist on Y-1 0, it has been re-energized through the bypass regulator. Which ONE of the following is the method for resetting the low suction pressure trip for P-8A? A. Momentarily place P-8A "AUTO/MANUAL" select switch to MANUAL position. B. Open then close breaker 72-228 on Panel 0-21. C. Place the local breaker control switch at 2400 V Bus 1C to the trip position momentarily. D. Depress the FAULT RESET push button on panel EC-187 (AFAS cabinet)

C. Place the local breaker control switch at 2400 V Bus 1C to the trip position momentarily.

Given the following: • Aux Feedwater Pump P-8B was in-service and then tripped on low suction pressure. • Preferred AC Bus Y-30 is out-of-service. • Inverter AC output breaker associated with Y-10 had previously tripped. After verifying there was no fault on Bus Y-1 0, it was re-energized via the bypass regulator. Which ONE of the following statments describes the action needed to reset the low suction pressure trip for P-8B to resume its normal operation? A. Place the P-8B MANUAL/AUTO select switch to the MANUAL postiion, and then return it to AUTO. B. Place the handswitch HS-0522B (steam supply from 'A' S/G) momentarily to the CLOSE position. C. Depress the FAULT RESET pushbutton on panel EC-187. D. Operate P-8B from panel C-150.

B. Place the handswitch HS-0522B (steam supply from 'A' S/G) momentarily to the CLOSE position

The Aux Feed Pumps Low Suction Pressure Trip may be reset from which ONE of the following sets of locations? A. C-01 panel, P-8A Breaker Cubicle, P-8C Breaker Cubicle. B. C-01 panel, P-8A Breaker Cubicle, P-8C Breaker Cubicle and C-150 panel. C. C-01 panel only. D. C-01 panel and C-150 panel.

A. C-01 panel, P-8A Breaker Cubicle, P-8C Breaker Cubicle.

Given the following plant conditions: • The plant is at full power. • P-8A Aux Feedwater (AFW) Pump is out of service. • "A" Steam Generator level lowers to 20% on all four safety channels. Based on the above plant conditions, which ONE of the following describes the operation of P-8C Aux Feedwater Pump and associated AFW flow controllers? (Assume no operator action.) FLOW CONTLER MODE AFW TO EACH S/G A. AUTO 100GPM B. CASCADE 165 GPM C. AUTO 165 GPM D. CASCADE 100 GPM

B. CASCADE 165 GPM

Given: Plant is at 70% power . • 'A' S/G level is 29.5%. • 'B" S/G level is 65%. • 'A' AFW pump breaker is racked out. • C-33 panel AFW controllers from 'C' AFW pump to 'A' and 'B' S/Gs are in manual-closed. • All other controls are in their NORMAL lineup. After four minutes have elapsed which ONE of the following is the status of the Auxiliary Feedwater System (AFWS)? A. AFW is being supplied to ONLY steam generator 'A'. B. AFW is being supplied to ONLY steam generator 'B'. C. AFW is being supplied to BOTH steam generators. D. AFW is BLOCKED to BOTH steam generators.

C. AFW is being supplied to BOTH steam generators.

``` Following a valid Aux Feedwater Actuation, which set of SIG levels would FIRST allow resetting of AFAS? A S/G B S/G A. 27% 25% B. 27% 27% C. 31% 27% D. 31% 31% ```

D. 31% 31%

Which ONE of the following describes a condition which would disable the Aux. Feedwater Pump P-8B low suction pressure trip? A.C-150 Auxiliary Shutdown Panel placed in-service. B. Loss of Preferred AC Bus Y-1 O. C. C-33 Auxiliary Shutdown Panel placed in-service. D. Loss of Preferred AC Bus Y-30.

A.C-150 Auxiliary Shutdown Panel placed in-service

Given the following conditions: • Plant is at full power. • T-2, Condensate Storage Tank temperature is 80°F. • T-81, Demin Water Storage Tank temperature is 65°F. • 00-21, "Inservice Test Procedure - Auxiliary Feedwater Pumps" is to be performed. • Auxiliary Feedwater flow will be initiated to BOTH Steam Generators at the programmed value for an Auxiliary Feedwater Actuation (AFAS). Prior to initiation of AFW flow, which ONE of the following is the MAXIMUM allowed Heat Balance power level? A. 99.5%. B. 99.2%. C. 99.1%. D. 99.0%.

B~ 99.2%.

Given the following conditions: • Plant is at full power. • T-2, Condensate Storage Tank temperature is 100°F. • T-81, Primary Makeup Water Storage Tank temperature is 70°F. • 00-21, "Inservice Test Procedure - Auxiliary Feedwater Pumps" is to be performed. • Auxiliary Feedwater flow will be initiated to BOTH Steam Generators at the programmed value for an Auxiliary Feedwater Actuation (AFAS). Prior to initiation of AFW flow, what is the MAXIMUM Heat Balance power level allowed? A. 99.5%. B. 99.4%. C. 99.3%. D. 99.2%.

C. 99.3%

Given the following conditions: • The plant is operating at 100% power. • AFW Pump P-8A is to be started for a test. • Total flow to the SGs will be 300 gpm. • Condensate Storage Tank temperature is 100°F. What is the MINIMUM amount that power must be reduced to perform this test? A. 0.5% B. 0.6% C. 0.7% D. 0.8%

B. 0.6%

From full power, a Loss of All Offsite Power occurs. DIG 1-1 did not start automatically, and will not start manually. Which Auxiliary Feedwater Pump(s) will be operating 1 minute after an Auxiliary Feedwater Actuation Signal is received? (Assume all other equipment functions as designed) A. ONLY AFW Pump P-8A. B. ONLY AFW Pump P-8B. C. AFW Pumps P-8B and P-8C. D. ONLY AFW Pump P-8C.

D. ONLY AFW Pump P-8C.

During a Loss of Main Feedwater the following plant conditions were observed. Both S/G narrow range levels are 29% Inverter #2 failed immediately prior to the Loss of Main Feedwater Motor Driven Aux. FW. Pump P-8A is Out of Service for Maintenance Which Aux. Feedwater pump(s) should be running, and if the normal Condensate Storage Tank water supply were to become unavailable, what would their alternate water source(s) be? A. Both the Turbine Driven Aux. FW Pump P-8B with alternate water source from Service Water, and the Motor Driven Aux. FW Pump P-8C with alternate water source from Fire Protection should be running. B. Only the Motor Driven Aux. FW Pump P-8C should be running with alternate water source from Service Water. C.Only the Turbine Driven Aux. FW Pump P-8B should be running with alternate water source from Fire Protection/ D. Both the Turbine Driven Aux. FW Pump P-8B with alternate water source from Fire Protection, and the Motor Driven Aux. FW Pump P-8C with alternate water source from Service Water should be running

C.Only the Turbine Driven Aux. FW Pump P-8B should be running with alternate water source from Fire Protection/

From full power; a Loss of All Offsite Power occurs. DIG 1-1 did not start automatically, and will not start manually. Which Auxiliary Feedwater Pump(s) will be operating 1 minute after an Auxiliary Feedwater Actuation Signal is received? (Assume all other equipment functions as designed) A. ONLY AFW Pump P-8A. B. ONLY AFW Pump P-8B. C. AFW Pumps P-8B and P-8C. D.ONLY AFW Pump P-8C.

D.ONLY AFW Pump P-8C.

``` With the plant qlt 25% power, FIC-0727/0749, AFW Flow Controller is considered OPERABLE if it is In: A. MANUAL. B. PF Mode. C. AUTO. D. CASCADE ```

D. CASCADE

Given the following conditions: • Plant is at full power when a Loss of All Offsite Power occurs • Only DIG 1-2 starts and begins load sequencing. • Reactor trips, but the Main Turbine does NOT automatically trip. • S/G levels quickly lower to approximately 32% before the NCO manually trips the Main Turbine. • 30 seconds after manually tripping the Main Turbine the NCO notes that AFW flow indicates 0 gpm to each S/G. ·A loss of Preferred AC Bus Y-20 occurred concurrent with the auto reactor trip. What action, if any, is required, and why? A. No action is required, since AFW Pump P-8C will start and deliver design flow to each S/G. B. The operator must manually initiate AFAS (Aux. Feed Actuation Signal) due to the Loss of Offsite Power. C. The operator must manually start AFW Pump P-8C since P-8B has failed to start on low S/G level. D. No action is required since both motor driven AFW pumps cannot be started and the turbine driven AFW pump will deliver design flow in 92 second

D. No action is required since both motor driven AFW pumps cannot be started and the turbine driven AFW pump will deliver design flow in 92 second

Given the following conditions: • A reactor trip trom full power occurred 15 minutes ago. • AFAS automatically actuated. • AFW Pump P-8A is running and delivering 165 gpm to each S/G. • P-8C is in AUTO, and not running. • 'A' S/G level is 38%, 'B' S/G level is 26%. Then, flow to 'A' S/G (via FIC-0749) is manually reduced to §ill gpm and flow to 'B' S/G (via FIC-0727) is manually reduced to 95 gpm. Which one of the following describes the expected response of AFW Pump P-8C, AND the reason for that response? A. Not start automatically, since P-8A is running and total AFW flow is above 165 gpm. B.Not start automatically, since P-8A is running and both S/G levels are greater than the AFAS setpoint. C. Start automatically, since one S/G level is outside of the normal band. D.Start automatically, since AFW flow is less than the minimum required.

D.Start automatically, since AFW flow is less than the minimum required.

With the plant at 100% power, AFW Pump P-8B became inoperable. 72 hours have transpired and a plant shutdown to MODE 3 was commenced. During the plant shutdown the following occurred: • Both Main Feed Pumps have tripped. • Reactor automatically tripped on S/G low level • The plant is currently in MODE 3. • All 4 Primary Coolant Pumps are in service. F'Sf/A • Bus 1C de-energized concurrent with the reactor trip (overcurrent trip) • AFW Pump P-8C is currently in-service • S/G Pressures are 990 psia. For the above conditions, which one of the following describes the minimum action(s) necessary for ensuring the AFW System will provide the required flow for adequate core cooling? A. No actions needed since the required flow will be met. B. Secure all 4 PCPs C. Reduce S/G Pressure to

C. Reduce S/G Pressure to

Which of the following describes the locations where CV-0737 A, AFW from P-8C to 'A' S/G can be controlled? A Control Room and C-150 B: C-150 and Panel C-33 C.Control Room and Panel C-33 D. Control Room and locally in CCW Hx Room

C.Control Room and Panel C-33

Which Auxiliary Feedwater System requirement addresses the concern for feedwater line water hammer A. Minimum required flow for AFW pumps B. Upper limits on AFW motor amps. C. Limits on Rx power levels when adding relatively cold water from T-2 Condensate Storage Tanks. D. Limits on S/G temperature and level when initiating flow through AFW Flow Control Bypasses CV-0736/0737.

D. Limits on S/G temperature and level when initiating flow through AFW Flow Control Bypasses CV-0736/0737.

A. will NOT automatically trip on low suction pressure.

``` Auxiliary Feedwater Pump P-8A will automatically trip on: A. low oil pressure. B. low suction pressure C. overspeed. D. high discharge flow. ```

B. low suction pressure

A valid AFW actuation (AFAS) signal is actuated. After several minutes, with no operator action, the Control Room operator notices that both P-8A and P-8C are running. Based on the above conditions, the Control Room Operator will also know that P-8A was NOT delivering at least 100 gpm to... A. both steam generators within 112.5 seconds of receipt of the AFAS signal. B. both steam generators within 30.5 seconds of receipt of the AFAS signal. C. at least one steam generator within 112.5 seconds of receipt of the AFAS signal. D. at least one steam generator within 30.5 seconds of receipt of the AFAS signal.

D.at least one steam generator within 30.5 seconds of receipt of the AFAS signal.

Given the following conditions: • The Auxiliary Feed Water system is NOT operating. •• Preparations are being made to feed the SGs using the AFW Bypass Valves, CV-0736 and CV-0737. Prior to using these valves, SG Temperatures must be (1) OR S/G Levels must be (2) (1) (2) A. 60% C. >300F 212F >60%

B. 60%

Given the following conditions: • Plant is at full power. • T-2, Condensate Storage Tank temperature is 80°F. • T-81 , Demin Water Storage Tank temperature is 65°F. • QO-21, "Inservice Test Procedure - Auxiliary Feedwater Pumps" is to be performed. • Auxiliary Feedwater flow will be initiated to BOTH Steam Generators at the programmed value for an Auxiliary Feedwater Actuation (AFAS). Prior to initiation of AFW flow, which ONE of the following is the MAXIMUM allowed Heat Balance power level? A. 99.5%. B. 99.2%. C. 99.1%. D. 99.0%.

B. 99.2%.

AFW Finished Flashcards

Check # 19 (85 cards)