Book 3 Flashcards by jott Singh

This regulation lists the requirements which must be met for anyone wishing to write an applicable jurisdictional examination.
Select one:

a.
Pressure Equipment Exemption Order

b.
Pressure Equipment Safety Regulation

c.
Pressure Welders Regulation

d.
Power Engineers Regulation

Power Engineers Regulation

How well did you know this?

Not at all

Perfectly

This group meets at least once a year on situations which they feel are important and relevant to Power Engineers and the fulfillment of their duties and responsibilities.
Select one:

a.
IPECC

b.
SOPEEC

c.
ACI

d.
ASME

e.
ANSI

ACI

How well did you know this?

Not at all

Perfectly

What code contains guidelines for the care and operation of heating boilers?
Select one:

a.
CSA B52.

b.
ASME Section IX

c.
ASME Section IV.

d.
CSA B51.

e.
ASME Section VI.

ASME Section VI.

How well did you know this?

Not at all

Perfectly

ASME-CSD-1 applies to which equipment?

a.
Boilers operating on electric power

b.
Boilers operating on biomass fuels

c.
Hot water heaters

d.
Direct gas-fired swimming pool heaters

Boilers operating on electric power

How well did you know this?

Not at all

Perfectly

Which topic is covered in the ASME Code Section I?

a.
Economizer

b.
Feedwater piping

c.
Condensate piping

d.
Blow off

Economizer

How well did you know this?

Not at all

Perfectly

If a complaint is made against a Power Engineering certificate holder, who conducts the preliminary investigation?

a.
Inspector

b.
Chief Inspector

c.
Chief Power Engineer

d.
Chief

Chief Inspector

How well did you know this?

Not at all

Perfectly

Which of the following is NOT a subsection of ASME BPVC, Section VII?

a.
Inspection

b.
Boiler operation

c.
Construction

d.
Appurtenances

Construction

How well did you know this?

Not at all

Perfectly

Water expands approximately ________ times when converted to steam

Select one:

a.
6000

b.
10,000

c.
1600

d.
100

1600

How well did you know this?

Not at all

Perfectly

Power Engineering and pressure plant regulations fall under which jurisdiction?

a.
Provincial

b.
National

c.
Federal

d.
Regional

Provincial

How well did you know this?

Not at all

Perfectly

What is one of the two main purposes of the CSA-B51 Boiler, Pressure Vessel, and Pressure Piping Code?

a.
To list requirements for mechanical rooms

b.
To promote uniform requirements among jurisdictions

c.
To define terms and equipment relating to refrigeration and air conditioning equipment

d.
To list and describe the various classifications of buildings and occupancies with examples of each classification

To promote uniform requirements among jurisdictions

How well did you know this?

Not at all

Perfectly

Which of the following is not a staffing requirement in a plant?

a.
The class of Power Engineer

b.
The class of chief engineer required

c.
The class of assistant engineer required

d.
The class of shift engineer required

The class of Power Engineer

How well did you know this?

Not at all

Perfectly

One of the national standards which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the:
Select one:

a.
CSA B51

b.
ASME Codes

c.
NFPA Codes

d.
ANSI Codes

CSA B51

How well did you know this?

Not at all

Perfectly

Power engineers are:
Select one:

A.
Qualified to perform any welding jobs in a power plant

B.
Skilled workers who operate and maintain the equipment in a power plant

C.
Automatically Safety code officers in a power plant

D.
Qualified to make design changes in a power plant

Skilled workers who operate and maintain the equipment in a power plant

How well did you know this?

Not at all

Perfectly

Which activity does not use steam?

Select one:

a.
removing skin from potatoes

b.
heavy oil recovery

c.
refrigeration systems

d.
computer chip manufacturing

computer chip manufacturing

How well did you know this?

Not at all

Perfectly

In the early days, owners of power plants hired _____ workers, who started out doing manual labour and through acquired experience they were promoted to jobs with gradually increasing levels of skill.
Select one:

A.
Trained

B.
Highly educated

C.
Unskilled

D.
Qualified

Unskilled

How well did you know this?

Not at all

Perfectly

Power engineers can usually expect to work:
Select one:

A.
Straight 12 hour day shifts

B.
Straight 12 hour night shifts

C.
Straight 8 hour night shifts

D.
Rotating shifts

Rotating shifts

How well did you know this?

Not at all

Perfectly

It much easier to have changes made to a _____ than it is to have changes made to an Act.
Select one:

a.
Act

b.
Bill

c.
Proclamation

d.
Regulation

Regulation

How well did you know this?

Not at all

Perfectly

What kind of government system does Canada have that divides power between regional and national governments?

a.
National

b.
Provincial

c.
Federal

d.
Regional

Federal

How well did you know this?

Not at all

Perfectly

In what century was the steam engine invented?

a.
17th

b.
19th

c.
21st

d.
15th

19th

How well did you know this?

Not at all

Perfectly

In general, all Acts will have the all of the following in common except:
Select one:

a.
The requirement for, and the methods of, inspecting, testing and certifying qualified repair and supervisory personnel will be clearly set out by the Act

b.
The responsibility and delegated authority of the Authorized Inspector, as well as the responsibilities of the owner or Chief Engineer of a plant where an inspection is being done, will all be clearly stated

c.
The designation of a Director or Administrator and a description of their various responsibilities.

d.
There will be a list of penalties, which could be levied for complying with the Act or Regulations

There will be a list of penalties, which could be levied for complying with the Act or Regulations

How well did you know this?

Not at all

Perfectly

In general, all Acts will have the all of the following in common except:
Select one:

a.
The purpose of the Act will always be included

b.
The scope of the Act

c.
The designation of a Director or Administrator and a description of their various responsibilities

d.
A listing of the Codes and standards that have not been adopted for use

A listing of the Codes and standards that have not been adopted for use

How well did you know this?

Not at all

Perfectly

The code that regulates mechanical refrigeration is the:
Select one:

a.
ASME Section I

b.
ASME Section IV

c.
CSA B-51

d.
CSA B-52

CSA B-52

How well did you know this?

Not at all

Perfectly

Definitions for terms such as “shift engineer,” “chief engineer” and “assistant engineer” may be found in:
Select one:

a.
The Canadian Labour Code

b.
ASME Code Section VIII

c.
CSA B-51

d.
The Power Engineers’ Regulations of a particular jurisdiction

The Power Engineers’ Regulations of a particular jurisdiction

How well did you know this?

Not at all

Perfectly

Which of these is the “Boiler, Pressure Vessel and Pressure Piping Code” ?
Select one:

a.
ASME BPV-PPC

b.
ASME Section I.

c.
CSA B51

d.
CSA B52.

CSA B51

How well did you know this?

Not at all

Perfectly

Committees that establish standards are composed primarily of which of the following elements? Select one: A. One government appointed standards board B. Only multi-National power corporations C. Experts from the industry, professional and insurance groups and all levels of government D. Only experts from the industry and government E. One independent safety and standardisation board

Experts from the industry, professional and insurance groups and all levels of government

The holder of a Certificate of Competency, the classification of which authorises him or her to act as a engineer, may sketch, construct, install, operate, repair, and give advice on all things pertaining to any _____ in which that person is employed. Select one: A. Welding shop B. Power plant C. Hydro plant D. Fish plant

Power plant

In order to produce greater efficiency, higher boiler pressures were used. This led to _____ due to the employment of unqualified power plant operators. Select one: A. Safer working conditions B. Economic gains C. Serious accidents D. Higher efficiency

Serious accidents

The provinces and territories of Canada are referred to as Select one: a. Bodies b. Jurisdictions c. Governments d. Authorities

Jurisdictions

One of the national legislative items which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the: Select one: a. ASME Codes b. NAFTA Codes c. CSA B52 d. ANSI Codes e. NFPA Codes

CSA B52

Unqualified individuals operating a power plant or pressure plant risk the _____ of the plant and the general public. Select one: A. Economy B. Resources C. Health D. Safety

Safety

This group recommends updates to the learning materials of each class of Power Engineer, and the criteria required to ensure a Power Engineer is properly qualified when a Certificate of Competency is issued. Select one: a. SOPEEC b. ASME c. ACI d. ANSI e. IPECC

IPECC

Which of the following is not a strategy developed to help shift workers reduce disruptions in health, performance, and work preparation? a. Lead a healthy life style with regular, nutritious meals and regular exercise patterns b. Raise the thermostat during sleep periods c. Try various methods for completely blocking out the light during daytime sleep periods d. Plan and maintain regular social activities, especially those aimed at supporting others

Raise the thermostat during sleep periods

Which part of CSA-B52 Mechanical Refrigeration Code describes the method used to extract heat? a. Refrigerating system classification b. Installation c. Refrigerant classification d. Occupancy classification

Refrigerating system classification

An international code which has been adopted and is enforced by all jurisdictions is the: Select one: a. Act b. ASME Code c. CSA B51 d. CSA B52

ASME Code

To standardize requirements across Canada, it is simpler for the jurisdictions across the country to adopt which existing codes? a. CSA, ASME, NPFA, and AIP b. CSA, ASME, NFPA, and AIP c. CSA, ASME, NFPA, and API d. CSA, ASME, NPFA, and API

CSA, ASME, NFPA, and API

In a power plant, the power engineer may function as a supervisor who directs others in the _____ operation on a shift. Select one: A. administrative and co-operative B. occasional careful C. shipping and receiving D. safe and efficient

safe and efficient

To register a boiler, pressure vessel, a pressure piping system, or a boiler fitting, within one of the provincial jurisdictions, Select one: a. The chief inspector of the jurisdiction must review and approve the design drawings and calculations b. Drawings must be submitted to the ASME c. The manufacturer need not have a quality control program in place d. The CSA must approve the design

The chief inspector of the jurisdiction must review and approve the design drawings and calculations

What code contains Rules For Construction of low-pressure hot water supply boilers? Select one: a. ASME Section IX b. ASME Section IV. c. ASME Section VIII. d. CSA B52. e. CSA B51.

ASME Section IV.

What code contains guidelines for refrigeration piping and heat transfer components? a. ASME Section VI b. CSA B51 c. ASME B31.5 d. ASME Section IX

ASME B31.5

Which code covers minimum safety requirements for steam and hot water boilers intended for low-pressure or low-temperature service? a. ASME BPVC, Section IV b. ASME Section VI c. ASME BPVC, Section VII d. ASME Section IID

ASME BPVC, Section IV

Symptoms of sleep deprivation are due to an accumulation of what effect caused by a long-term disruption to the circadian rhythm? a. Stress b. Depression c. Acid reflux d. Anxiety

Stress

The "Pressure Vessels" section of the B-51 code identifies pressure vessels and their installation, including pressure vessel inspection openings. This section also shows the design of cushion tanks, blow-off vessels, and the installation of: Select one: a. Blowdown tanks. b. Hydropneumatic tanks c. Dearators. d. Boiler drums.

Hydropneumatic tanks

What code contains Rules For Construction of Power Boilers? Select one: a. CSA B51. b. ASME Section I. c. CSA B52. d. ASME Section VIII.

ASME Section I.

What ASME code contains Recommended Guidelines For The Care of Power Boilers? Select one: a. CSA B51. b. CSA B52. c. ASME Section VII. d. ASME Section VIII e. ASME Section I.

ASME Section VII.

The main or primary document which must be passed through the jurisdictional parliament is a/an: Select one: a. Proclamation b. Bill c. Edict d. Act e. Regulation

Act

Which code subsection discusses the diﬀerent types of boiler fuels for heating boilers? a. ASME BPVC, Section IV b. ASME BPVC, Section VII c. ASME Section IID d. ASME Section VI

ASME Section VI

What is one of the two main purposes of the CSA B-52 code? Select one: a. 2, 4 b. The various classifications of buildings and occupancies are listed and described with examples of each classification given. c. To promote uniform requirements among the provinces and territories d. Terms and equipment relating to refrigeration and air conditioning equipment are defined.

To promote uniform requirements among the provinces and territories

The main purpose of the Boiler and Pressure Vessel Code is: Select one: a. The promotion of efficient combustion b. To protect life and property c. To promote efficient boiler operation d. To promote qualified training for operators

To protect life and property

It much easier to have changes made to a regulation than it is to have changes made to a/an: Select one: a. Act b. Proclamation c. Bill d. Edict

Act

What code regulates power boilers used in locomotive service? Select one: a. ASME Section VII. b. ASME B31.3. c. ASME Section I. d. CSA B52. e. ASME Section IX

ASME Section I.

A welder performance qualification test: Select one: a. Is a practical welding test b. Must be completed immediately after the welder obtains a certificate of qualification. c. Is only required by welders working on steel structures d. Is only required once in a welder's career

Is a practical welding test

Which of the following is required in order to progress to a higher certificate? Select one: A. Education, experience, the next lower level certificate, and pass SOPEEC examinations B. Hold the next lower level certificate only C. Experience and education D. Both education and the next lower level certificate

Education, experience, the next lower level certificate, and pass SOPEEC examinations

When applying to write a Power Engineer certificate of competency examination, the candidate must: Select one: a. Undergo mandatory drug testing b. Hold the next lower class of qualification c. Pass a criminal records check d. Pass both a written and oral examination

Hold the next lower class of qualification

What does the term CSA stand for with respect to Power Engineering? Select one: a. Catalytic Site Analysis b. Combustion Safety Authority c. Canadian Security Agency d. Congressional Standards Agency e. Canadian Standards Association

Canadian Standards Association

Humans have a natural, regular cycle of being tired and energized. What is this natural, individual cycle called? a. Wake sleep cycle b. 24-hour clock c. Circadian rhythm d. Homeostasis

Circadian rhythm

The Act has _____ which are pursuant to the enforcement of the Act. Select one: a. Laws b. Proclamations c. Edicts d. Bills e. Regulations

Regulations

This group of members of jurisdictional bodies meets at least annually. Answering to the ACI, they ensure that all Power Engineer examinations meet the requirements set by the jurisdictional legislative bodies. Select one: a. ASME b. ACI c. ANSI d. SOPEEC e. IPECC

SOPEEC

Clear definitions for terms and equipment relating to refrigeration and air conditioning equipment are defined in the _____. Select one: a. ASME Section I b. ASME Section VII c. CSA-B52 d. CSA-B51

CSA-B52

Providing healthy food options that are available at all hours helps support which habits? a. Work b. Support c. Personal d. Health

Work

The investigation of an accident involving a power plant: Select one: a. may be carried out by the Chief Inspector of the jurisdiction. b. Is not specified in a jurisdictional Act or Regulation . c. Is not of concern to the Chief Inspector d. Is clearly outlined in the Engineer's Regulations

may be carried out by the Chief Inspector of the jurisdiction.

Which of these is the "Mechanical Refrigeration Code"? Select one: a. ASME Section I. b. ASME MRC c. CSA B52. d. CSA B51.

CSA B52.

Which of these is the "Boiler, Pressure Vessel and Pressure Piping Code" ? Select one: a. ASME Section I. b. ASME BPV-PPC c. CSA B51 d. CSA B52.

CSA B51

It much easier to have changes made to a _____ than it is to have changes made to an Act. Select one: a. Regulation b. Bill c. Proclamation d. Act

Regulation

What is one of the two main purposes of the CSA B-52 code? Select one: a. Terms and equipment relating to refrigeration and air conditioning equipment are defined. b. 2, 4 c. To promote uniform requirements among the provinces and territories d. The various classifications of buildings and occupancies are listed and described with examples of each classification given.

To promote uniform requirements among the provinces and territories

Is a practical welding test

This regulation lists the requirements which must be met for anyone wishing to write an applicable jurisdictional examination. Select one: a. Pressure Welders Regulation b. Pressure Equipment Safety Regulation c. Pressure Equipment Exemption Order d. Power Engineers Regulation

Power Engineers Regulation

What code regulates power boilers used in locomotive service? Select one: a. ASME Section I. b. CSA B52. c. ASME Section VII. d. ASME B31.3. e. ASME Section IX

ASME Section I.

IPECC

In general, all Acts will have the all of the following in common except: Select one: a. The designation of a Director or Administrator and a description of their various responsibilities. b. The requirement for, and the methods of, inspecting, testing and certifying qualified repair and supervisory personnel will be clearly set out by the Act c. The responsibility and delegated authority of the Authorized Inspector, as well as the responsibilities of the owner or Chief Engineer of a plant where an inspection is being done, will all be clearly stated d. There will be a list of penalties, which could be levied for complying with the Act or Regulations

There will be a list of penalties, which could be levied for complying with the Act or Regulations

Which of the following is not a strategy developed to help shift workers reduce disruptions in health, performance, and work preparation? a. Raise the thermostat during sleep periods b. Plan and maintain regular social activities, especially those aimed at supporting others c. Lead a healthy life style with regular, nutritious meals and regular exercise patterns d. Try various methods for completely blocking out the light during daytime sleep periods

Raise the thermostat during sleep periods

The Act has _____ which are pursuant to the enforcement of the Act. Select one: a. Laws b. Bills c. Edicts d. Proclamations e. Regulations

Regulations

In a power plant, the power engineer may function as a supervisor who directs others in the _____ operation on a shift. Select one: A. safe and efficient B. administrative and co-operative C. shipping and receiving D. occasional careful

safe and efficient

Symptoms of sleep deprivation are due to an accumulation of what effect caused by a long-term disruption to the circadian rhythm? a. Acid reflux b. Anxiety c. Depression d. Stress

Stress

The "Pressure Vessels" section of the B-51 code identifies pressure vessels and their installation, including pressure vessel inspection openings. This section also shows the design of cushion tanks, blow-off vessels, and the installation of: Select one: a. Boiler drums. b. Dearators. c. Hydropneumatic tanks d. Blowdown tanks.

Hydropneumatic tanks

may be carried out by the Chief Inspector of the jurisdiction.

Hold the next lower class of qualification

What kind of government system does Canada have that divides power between regional and national governments? a. Provincial b. Federal c. Regional d. National

Federal

The holder of a Certificate of Competency, the classification of which authorises him or her to act as a engineer, may sketch, construct, install, operate, repair, and give advice on all things pertaining to any _____ in which that person is employed. Select one: A. Power plant B. Fish plant C. Hydro plant D. Welding shop

Power plant

Which of the following is not a staffing requirement in a plant? a. The class of Power Engineer b. The class of chief engineer required c. The class of shift engineer required d. The class of assistant engineer required

The class of Power Engineer

Which code covers minimum safety requirements for steam and hot water boilers intended for low-pressure or low-temperature service? a. ASME BPVC, Section VII b. ASME Section VI c. ASME BPVC, Section IV d. ASME Section IID

ASME BPVC, Section IV

One of the national legislative items which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the: Select one: a. NAFTA Codes b. NFPA Codes c. ASME Codes d. CSA B52 e. ANSI Codes

CSA B52

Unqualified individuals operating a power plant or pressure plant risk the _____ of the plant and the general public. Select one: A. Economy B. Safety C. Resources D. Health

Safety

In what century was the steam engine invented? a. 19th b. 15th c. 17th d. 21st

19th

Which topic is covered in the ASME Code Section I? a. Blow off b. Economizer c. Condensate piping d. Feedwater piping

Economizer

The provinces and territories of Canada are referred to as Select one: a. Authorities b. Jurisdictions c. Governments d. Bodies

Jurisdictions

The main or primary document which must be passed through the jurisdictional parliament is a/an: Select one: a. Proclamation b. Edict c. Regulation d. Bill e. Act

Act

If a complaint is made against a Power Engineering certificate holder, who conducts the preliminary investigation? a. Chief Power Engineer b. Chief Inspector c. Inspector d. Chief

: Chief Inspector

Unskilled

Power Engineering and pressure plant regulations fall under which jurisdiction? a. Regional b. Provincial c. Federal d. National

Provincial

The chief inspector of the jurisdiction must review and approve the design drawings and calculations

What does the term CSA stand for with respect to Power Engineering? Select one: a. Canadian Standards Association b. Combustion Safety Authority c. Canadian Security Agency d. Catalytic Site Analysis e. Congressional Standards Agency

Canadian Standards Association

Which of the following is NOT a subsection of ASME BPVC, Section VII? a. Inspection b. Construction c. Appurtenances d. Boiler operation

Construction

It much easier to have changes made to a regulation than it is to have changes made to a/an: Select one: a. Bill b. Edict c. Proclamation d. Act

Act

Which activity does not use steam? Select one: a. heavy oil recovery b. computer chip manufacturing c. refrigeration systems d. removing skin from potatoes

The correct answer is: computer chip manufacturing

To protect life and property

Which of these is the "Mechanical Refrigeration Code"? Select one: a. CSA B51. b. ASME Section I. c. ASME MRC d. CSA B52.

CSA B52.

One of the national standards which each jurisdiction in Canada has adopted as part of their applicable Act and/or Regulations is the: Select one: a. ANSI Codes b. CSA B51 c. ASME Codes d. NFPA Codes

CSA B51

Serious accidents

Which code subsection discusses the diﬀerent types of boiler fuels for heating boilers? a. ASME BPVC, Section VII b. ASME BPVC, Section IV c. ASME Section IID d. ASME Section VI

ASME Section VI

In general, all Acts will have the all of the following in common except: Select one: a. The scope of the Act b. A listing of the Codes and standards that have not been adopted for use c. The purpose of the Act will always be included d. The designation of a Director or Administrator and a description of their various responsibilities

A listing of the Codes and standards that have not been adopted for use

Book 3 Flashcards

(100 cards)