Carpentry Flashcards
(166 cards)
1
Q
Purpose of bill c-45
A
Protects workers and unforces criminal charges
2
Q
Most common true of shackle in rigging
A
Anchor type with screw pin
3
Q
The higher the gage number the thicker/ thinnner the screw
A
Thicker
4
Q
10-22x1.5”
What does the 10 mean
A
Gauge
5
Q
Does a 6 by 7 wire rope have more threads then a 6 by 19
A
No
6
Q
Which products is the WHMIS system designed to provide safety for
A
Controlled
7
Q
Posidrived slotted flattened Robertson which 2 is not a screw head
A
Flattend
8
Q
What grit sand paper is used to finish hardwood prior to coating
A
150/200
9
Q
Jointing lumber meaning
A
Making edges straight
10
Q
What speed does a router spin at
A
30000rpm
11
Q
Explosive actuated tools are considered light duty with a shank diameter of what
A
4.83mm
12
Q
Ripsaw handsaw use ?
A
Cuts with the grain of wood
13
Q
Explosive actuated tools how close to the edge of the steel can they be used
A
15mm
14
Q
What is needed to be done to adjust the depth of cut on a router
A
Adjust the infeed table
15
Q
In concrete slabs surface vibration is done in slab up to home many mm thick
A
200mm
16
Q
Typical framed interior opening for a type b furnace flue in mm
A
25mm
17
Q
How many days must concrete be protected from freezing
A
3-5 days
18
Q
Wood berms supported by concrete what must be done
A
Treated with wood preservative
19
Q
Solid wood floors joists where is the neutral plane
A
Along the horizontal center of the joist
20
Q
Integral part of PWF design
permanent wood foundation
A
A sump pit
21
Q
What will happen to a steel beem being compressed
A
It will shrink
22
Q
At what height should exterior bracing be added to insulated concrete formes
A
1.2 meters
23
Q
When can steel pipes be used as a column with a floor frame support
A
When the wall thickness is not less then 4.76mm
24
Q
When must screeding be completed on a concrete slab
A
Before excess bleed water is produced
25
What type of drawing is best used to show an object as it is seen by the human eye
3 point
26
What does the abbreviation fl stand for
Flat
27
How are main object lines shown on a drawing
With an extra heavy continuous line
28
What cross cut saw gives the best results when hand sawing plywood
13/15 points
29
Hand signal for raise load slowly
Place your arm out and palm down and open. Make the hoist signal to the bottom of your hand
30
What is the signal to shorten the boom or trolly with cranes
Make fists with outstretched thumbs and motion together
31
What is the finish type for a finishing male
Galvanized
32
What type of chisel is used for more delicate work
Bevel edge
33
When using extension cords a number 14 cord should be used for how many feet maximum
25 feet
34
On a hollow grind chisel the primary angle is what
30 degrees
35
What depth must the edges of a concrete slab be to supply adequate support for the base of the PWF FRAMING
25mm
36
How is the diameter of a wire rope measured
Across the crowns of the wire rope
37
How many u bolts are required for a 1 inch rope
4
38
Hand signal for a regular stop
1 arm is waved back and fourth perpendicular to the slingmans body
39
Explosive actuated tools with a paper wad must be used with high velocity tools
True
40
What grit sandpaper is used for initial sanding of finish coats
200/400
41
What grit sandpaper is used in initial sanding of rough wood and paint removal
36/60
41
42
What speed does a drywall gun spin at
6000rpm
43
A crosscut saw usually has how many teeth per inch
7
44
Building permits are not required for a swimming pool when it is how deep?
600mm
45
What is a building permit
Permission from the city to erect a new building
46
Correct name for a basement slab
Slab on ground
47
Properly set up water tables are accurate to what ?
1/16 of an inch
48
What type of dimensioning style is used on machine drawings
Unidirectional
49
Class A fire extinguisher
Green
Ordinary combustibles
50
Class B fire extinguisher
Red
Flammable liquids and gases
51
Class C fire extinguisher
Blue
Electrical
52
Class D fire extinguisher
Yellow
Combustible metals
53
Class K fire extinguisher
Black
Kitchen fires
54
Which of the following is true with respect to PPE
The use of PPE equipment is considered the lowest level of managing hazards in the workplace
55
What type of anchor recommends a manufacturer supplied bit
Masonry screw
56
What type of cement would commonly used in general construction of foundations and walls
Type 1
57
Advantages of pvc hose over rubber hose
More flexible
Easier to handle in cold temperatures
Can handle rough treatment
58
How many degrees should the body of a bit be to the face of the wheel when sharpening a twist drill bit on a grinder
59 degrees
59
What will the result if a plane iron is ground so that a bevel occurs on the flat side
Shavings that clog the plane
60
In saw blade design what is the grind
The top bevel angle of the tooth
61
How can striations on a grinding wheel be removed
By wetting and by honing
62
What type of explosive actuated tools pin should be used in highly corrosive environments
Stainless steel pin
63
A crosscut saw has how many teeth per inch
8
64
Green wire in extension cord is
Ground
65
White wire in extension cord is
Neutral
66
Black wire in extension cord is
Live
67
How close to the edge of concrete can an explosive actuated tools be used
75mm
68
Properly set explosive actuated tools tools penetrates to a depth of him many times the diameter of the shank
6/8 times out of
69
Triangular taper files are used to grind teeth at what angle
60 degrees
70
You can safely excavate for a basement using a straight cut without shouting up to what depth
1.5m
71
Building permits are not required for accessory building that are not greater the what
10m2
72
If floors joists are lapped over a center supporting beam the maximum projection beyond the face of the beam is him many mm
250mm
73
What does the abbreviation cl stand for
Closet
74
What hight should be used for tiles in a drawing in mm
6mm
75
How are outlines of footings shown on drawings
With dashed lines
76
Which plan is the most referenced in a group of prints
Floor plan
77
What does EE stand for
Each end
78
What are single point perspective drawings similar to
Oblique drawings
79
When setting up outriggers the carrier must be beveled in how many planes
2 planes
80
What is the typical application for SEL TF canopy exterior standard plywood
Underlayment, hoarding and used where sanded material is not required
81
When is lumber called timber
114mm
82
What is the disadvantage of using a standard coupler on an air line
Standard coupler greatly reduce airflow
83
What is not required for a compressor that has a ceramic sleeved cylinder
Oil
84
When using an explosive actuated tool in concrete how close should shots be together
75mm
85
What should always be done when replacing the belt on the belt sander
Check the inside for a direction arrow
86
The part of a hammer that absorbes the impact of the hammer
The post
87
What is the offset base model, laminate trimmer used for
To trim edges against a wall
88
What is the maximum speed allowed for a fastener to be classified as a low velocity tool
90 m/ps
89
In ICF concrete should be poured up to a maximum of how much per lift
1200
90
How should wood columns be separated from concrete when in contact
Type s roll roofing
91
Max distancy allowed before blocking in between floor joists
2100mm
92
How are toilet flanges installed
So the centre of the drain is 12.5 inches from the wall
93
Typical framed exterior opening for a chimney
12mm
94
Building permits are not required for a fence how tall
1m
95
96
When all weeping tile has been installed it must be covered by how much clear gravel
150mm
97
When using a drafting board it is recommended that the dimensions should be at least how many millimetres larger in both directions then the anticipated paper size
150mm
98
When referring to residential door systems what is not a standard layout 200mm
300mm
400mm
600mm
200mm
99
Area of a circle
Pie r squared
100
Perimeter of circle
2 pie r
101
What hight should be used for notes and diminishing on a print
3.0mm
102
What lines are used for dimension and extension lines
Continuous thin lines
103
What pencil has the hardest led
9h
7h
5h
H
9h
104
Common print size in north America
22/34
105
What type of pencil should be used for center lines
4h
106
Where are fire alarm systems info usually found on blueprints
On the floor plan
107
In most cases how are paper sizes determined
By folding the length in half of an existing sheet to arrive at the next size
108
Volume of a cone
1/3 pie r squared
109
What is the minimum wattage requirements for a generator used for typical carpentry tools on site
3000
110
What will increase when adding excess water to a batch of concrete
Shrinkage
111
A scaffold must be anchored by one tie for how many meter horizontal intervals
6.4
112
What is a finishing sander called
Pad sander
113
How should the chain be adjusted on a chain saw
So that when lifted the chain does not leave the bar
114
What is the size of a band saw determined by
The diameter of the rubber rimmed wheels
115
For explosive actuated tools what is the minimum thickness of steel
5mm
116
What does dressing lumber mean
Smoothing the rough surfaces
117
Where are measurements shown on a drawing when installing footings
To the outside edge of the foundation wall
118
Rebar dowels should be installed in the footings at intervals of how many millimetres max when installing a concrete block basement
1200mm
119
If rebar is placed 1inch higher then recommend this can reduce the slabs strength by what
20%
120
Where will the highest stress level occur when referring to floors joists
At the top and bottom of the beam
121
A footing must have a minimum thickness of what
100mm
122
What is the maximum slump allowable for concrete used for footings
150mm
123
What does the abbreviation FS stand for
Foresight
124
What is a common shop drawing size for North America in inches
17/22
125
What is honey coming in wood
White or brown spots caused by fungus with cellulostic substance
126
What is a loose knot
They often have bark around them
127
What is an unsound knot
It contains decay
128
Fas grade hardwood should be at least how many millimetres wide
150mm
129
What is the finish type for a finishing male
Bright and hot galvanizing
130
In saw blade design what is a kerf
The width of the face of a tooth
131
What is the recommended angle for the cutting edge of a chisel
25 degrees
132
An engineer must design temporary protective structures in a excavation that is over how many meters depth
3m
133
Block wall foundations how are rebar and concrete added to block cavities
1.2 m intervals or closer
134
International colour code for survey markings
Pink
135
You can safely excavate for a basement using a straight cut without shoring to a maximum depth of what
2100
136
Recommend model size when pouring ICF walls
75m
137
How many parts does a dimension line have
4
138
How is it drawn on a print when the elevation of a beam is shown above the cutting line
A phantom line
139
What are the characteristics of hardwoods
They shed their leaves in the fall
140
What is a typical application go G1S canply exterior plywood
Used where appearance or smooth sanded surface for 1 or more face is important
141
What is ringshake
It occurs between growth rings to masterly or fully encircle the pith
142
What class of csa eye protection are respirator face pieces in
7
143
Hat types of router bit is used as a flush trimmer
Pilot cutter
144
What would adjusting the outfeed table too high of a jointer cause
A taper to form
145
What speed does a screw gun spin at
2500rpm
146
How is a drill press sized
Chuck size
Length of quill travel
Number of speeds
147
What is the safety stop on a chain saw called
Chain break
148
What is the thickness of a slab on grade foundation
Thicker on the outside perimeter
149
What is added to concrete to increase the slump without adding water
Agronite
150
At what hoist length do headers require engineer design
3200mm
151
How are labels handles under WHMIS
By the global harmonized system
152
What is the name of abrupt dressing in the edge surface usually near the end
Machine offset
153
What are the uses of poplar
Plywood, plywood core, light construction, mouldings
154
How far must a ladder protrude above the landing spot
1 metre
155
A cantilever joist must project inwards mow much
Twice as much as the projection
156
Strongest type of rope
Synthetic fiber rope
157
What is the hardening process of concrete called
Hydration
158
Footwear with a yellow triangle is what grade of protection
Grade 2
159
How are explosive actuated tools strengths coded
12 level system
160
How many degrees is the lip clearance angle for general purpose twist drill bit
12 degrees
161
In saw blade design what is the bevel
The blade specific pattern
162
What does dressing lumber mean
Smooth the rough surfaces
163
International colour for reclaimed water
Purple
164
How deep should control joints be cut
1 quarter the slab
165
What does SP stand for
Stand pipe
