NAMP Appendix E

Question 1

What does Action Taken Code “A” signify and when is it used?

Answer 1

No Repair Required - When deficiency cannot be duplicated or the equipment is operating within allowable tolerances. (Adjustment may be made under this Action Take Code)

Question 2

What does Action Taken Code “C” signify and when is it used?

Answer 2

Repair – Repairable item identified by Work Unit Code (WUC) has been repaired. (includes cleaning, disassembly, inspection, reassembly, lubrication, replacement of integral parts, and adjustments)

Question 3

What does Action Taken Code “D” signify and when is it used?

Answer 3

Work Stoppage, Post and Pre Deployment, and Intermediate Maintenance Activity (IMA) Support – Close out MAF’s when component repair is performed at another facility.

Question 4

What does Action Taken Code “F” signify and when is it used?

Answer 4

Failure of items undergoing Check and Test – Work Requests and I-Level Assisting Work Centers MAFs only.

Question 5

What does Action Taken Code “Z” signify and when is it used?

Answer 5

Corrosion Treatment – Cleaning, treatment, priming, and painting of corroded items that require No Repair both on equipment or in shop.

Question 6

What is BCM 1?

Answer 6

Repair Not Authorized

Question 7

What is BCM 2?

Answer 7

Lack of Equipment, Tools, or Facilities

Question 8

What is BCM 3?

Answer 8

Lack of Technical Skills

Question 9

What is BCM 4?

Answer 9

Lack of Parts

Question 10

What is BCM 5

Answer 10

Fails Check and Test

Question 11

What is BCM 6?

Answer 11

Lack of Technical Data

Question 12

What is BCM 7?

Answer 12

Beyond Authorized Repair Depth

Question 13

What is BCM 8?

Answer 13

Administrative

Question 14

What is BCM 9?

Answer 14

Condemned

Question 15

What is Job Status Code A1?

Answer 15

Pre-Induction Screening

Question 16

What is Job Status Code IW?

Answer 16

In Work

Question 17

What is Job Status Code JC?

Answer 17

Job Complete

Question 18

What is Job Status Code M2?

Answer 18

Support Equipment (SE), Hangar, Hangar Deck Spaces or Facilities - Lack of adequate SE, maintenance area, or utility services, such as electricity or air pressure.

Question 19

What is Job Status Code M3?

Answer 19

Backlog - Workload in excess of work center capability.

Question 20

What is Job Status Code M4?

Answer 20

Off-shift Hours - Maintenance requirement exists beyond normal working hours.

Question 21

What is Job Status Code M5?

Answer 21

Other - Performance of maintenance precluded by weather, operational conditions, general drill, training, ceremonies, open house, shipboard or shore station imposed restrictions, etc.

Question 22

What is Job Status Code M6?

Answer 22

Awaiting Aircraft Intermediate Maintenance Department Maintenance (AIMD)

Question 23

What is Job Status Code M8?

Answer 23

Awaiting other shops or maintenance actions - This code will be documented when no further maintenance can be performed due to other shops or maintenance actions.

Question 24

What is Job Status Code CT?

Answer 24

Awaiting maintenance Cure Time - This code will be used when a maintenance task requires time for curing of an adhesive, sealant, or paint before the maintenance can continue or be completed.

Question 25

What is Job Status Code WB?

Answer 25

In Transit from Awaiting Parts Locker

Question 26

What is Job Status Code WP?

Answer 26

Awaiting Parts in Shop

Question 27

What is Job Status Code WQ?

Answer 27

Awaiting Parts in Awaiting Parts Locker

Question 28

What is Job Status Code WS?

Answer 28

Awaiting Parts Work Stoppage

Question 29

What is Job Status Code WT?

Answer 29

In Transit to Awaiting Parts Locker

Question 30

What is Work Unit Code 030 used for?

Answer 30

Corrosion Prevention - Used when documenting unscheduled corrosion prevention, including unscheduled aircraft washing.

Question 31

What is Work Unit Code 049 used for?

Answer 31

Preservation and Depreservation - Used when end items are preserved for temporary or long term storage or shipment, and for depreservation.

Question 32

What is the Technical Directive (TD) Status Code “A”?

Answer 32

Assisting Work Center

Question 33

What is the Technical Directive (TD) Status Code “C”?

Answer 33

Complied With

Question 34

What is the Technical Directive (TD) Status Code “D”?

Answer 34

Does Not Apply (Requires QAR Verification)

Question 35

What is the Technical Directive (TD) Status Code “P”?

Answer 35

Previously Complied With

Question 36

What is the Technical Directive (TD) Status Code “Q”?

Answer 36

TD Removal

Question 37

What is the Technical Directive (TD) Status Code “W”?

Answer 37

Work in Progress

Question 38

What is the Technical Directive Code for an Avionics Change?

Answer 38

Avionics Change (AVC 54)

Question 39

What is the Technical Directive Code for an Avionics Bulletin?

Answer 39

Avionics Bulletin (AVB 55)

Question 40

What is the Technical Directive Code for a Support Equipment Change?

Answer 40

Support Equipment Change (SEC 62)

Question 41

What is the Technical Directive Code for a Support Equipment Bulletin?

Answer 41

Support Equipment Bulletin (SEB 63)

Question 42

What is the Technical Directive Code for a Support Software Change?

Answer 42

Support Software Change (SSC 95)

Question 43

What is the Technical Directive Code for a Support Software Bulletin?

Answer 43

Support Software Bulletin (SSB 96)

Question 44

When is Transaction Code 11 used?

Answer 44

11 – I-Level when closing out a maintenance action. On supporting documents where corrosion treatment is performed at the IMA and this treatment is a separate and distinct action apart from the required repair.

Question 45

When is Transaction Code 31 Used?

Answer 45

31 - Work performed on a removed repairable component with no failed parts or awaiting parts documented in the Failed/Required Material blocks.

Question 46

When is Transaction Code 32 Used?

Answer 46

32 - Work performed on a removed repairable component with failed parts, awaiting parts, or cannibalization actions documented in the Failed/Required Material blocks.

Question 47

When is Transaction Code 41 Used?

Answer 47

41 - TD compliance with no part number change or non-serialized components.

Question 48

When is Transaction Code 47 Used?

Answer 48

47 - TD compliance on all serialized components, regardless of whether there is a part number change.

Question 49

How many positions are there in an SM and R code?

Answer 49

Six Positions

Question 50

Which position(s) of the SM and R Code contain the Source?

Answer 50

1st and 2nd Positions

Question 51

Which position(s) of the SM and R Code contain the Maintenance capability?

Answer 51

3rd and 4th Positions

Question 52

Which position(s) of the SM and R Code contain the Recoverability?

Answer 52

5th

Question 53

Which position(s) of the SM and R Code contains the Service Option Code?

Answer 53

6th

Question 54

What information is provided by the Source Position (Positions 1 and 2) of an SM and R Code?

Answer 54

Means of Acquiring Support

Question 55

What information is provided by the 3rd position of an SM and R Code?

Answer 55

Use: Lowest level authorized to remove/replace the item.

Question 56

What information is provided by the 4th position of an SM and R Code?

Answer 56

Repair: Lowest level with capability and resources to perform complete repair action.

Question 57

What information is provided by the 5th position of an SM and R Code?

Answer 57

Disposition: When unserviceable or uneconomically repairable condemn or dispose.

Question 58

What information is provided by the 6th position of an SM and R Code?

Answer 58

Assigned to support items to convey specific information to the service’s logistics community/operating forces.