Operation

Question 1

At what engine load can an AAQS be stopped?

Answer 1

Below 35%

Question 2

After an AAQS is stopped, when can engine load be increased again?

Answer 2

When its temperature is above

Question 3

Conditions of AAQS hot start

Answer 3

Engine load < 50 % and keep this load until exhaust gas outlet temp is < 100 C

Question 4

Can AAQS be pre-started in port?

Answer 4

No

Question 5

Can AAQS be pre-started at sea?

Answer 5

Yes

Question 6

At what engine load can HFO to MGO changeover commence?

Answer 6

Below 60%

Question 7

At what HFO temperature can changeover to MGO commence

Answer 7

Below 100 C

Question 8

At what MGO temperature can changeover to HFO commence?

Answer 8

At 60 C

Question 9

When MGO return can be open?

Question 10

What is the volume of engine fuel system?

Question 11

What is the minimal AAQS outlet pH worldwide?

Answer 11

4.0

Question 12

Which AAQS’s have filtration capability?

Answer 12

1 and 4

Question 13

Can both 1 and 4 AAQS run filtration at the same time?

Answer 13

No

Question 14

When AAQS filtration should be started?

Answer 14

Upon FWE

Question 15

When HFO return should be open?

Question 16

At which point fuel filtration should change over to simplex?

Answer 16

When the B&K flushes with MGO

Question 17

What is the typical DG MGO pressure?

Answer 17

10.0 bar

Question 18

Where is DG 1 rack 1 located?

Question 19

What mode is biosludge discharge?

Answer 19

Yellow OD

Question 20

What mode is AAQS start?

Answer 20

Yellow plus

Question 21

What mode is wastewater ashore discharge?

Answer 21

Yellow OD

Question 22

What mode is engine after maintenance startup?

Answer 22

Yellow plus

Question 23

What is the operation mode for fuel grade changeover

Answer 23

Yellow OD for start and completion

Question 24

What is considered the start of changeover from HFO to MGO?

Answer 24

When DGs are set to the load as per FOBAS calculator after HFO manual valve is closed.

Question 25

What is the DG fuel system quantity?

Answer 25

1.6 ton

Question 26

How to prevent EGCS from starting automatically?

Answer 26

Press STOP on the panel.

Question 27

How to set EGCS to standby on a stopped engine?

Answer 27

Press START on the panel

Question 28

What Maneuvering mode on EGCS does?

Answer 28

It sets a fixed wash water flow to the tower

Question 29

How to refill azipods seal tanks!

Question 30

How to transfer thrusters control to the bridge?

Answer 30

If the screen is inactive, press any button. Press Fx once

Question 31

How to take thrusters control from the bridge?

Answer 31

If the screen is inactive, press any button. Press Fx followed by Enter.

Question 32

How to start thrusters?

Answer 32

If the screen is inactive, press any button. Press Start Sequence Fx.

Question 33

How to stop thrusters?

Answer 33

If the screen is inactive, press any button. Take control by pressing Fx and Enter. Press Fx Stop Sequence

Question 34

How to start individual thrusters?

Answer 34

If the screen is inactive, press any button. Start thruster hydraulic unit, then start thruster.

Question 35

How to zero thruster pitch?

Answer 35

Start thruster hydraulic unit(s). Alternatively press Test button

Question 36

Which operation mode is departure and arrival?

Question 37

When fuel figures need to be taken?

Answer 37

At start and stop of fuel changeover. At start and completion of stand by arrival or departure.

Question 38

What is the max recommended load on MGO for a DG?

Answer 38

75%