Parameters

Question 1

When inboard engine is run above 40% N1, the symmetrical engine must be within…

Answer 1

5% N1

Question 2

Icing conditions are…

Answer 2

Below 50°F and moisture

Question 3

Do not engage starter above…

Answer 3

25% N2

Question 4

Engine starter duty cycle for starting

Answer 4

90 sec on, 60 sec off
90 sec, 60 sec
90 sec, 10 min off

Question 5

Engine starter duty cycle for motoring…

Answer 5

5 min on, 10 min off
5 min, 30 min
5 min, 30 min

Question 6

Starter light fails to go out 10 sec after 45% N2

Answer 6

• throttle to cutoff
• engine bleed air switch off

Question 7

Air temp <32°F heat MEC…

Answer 7

10 min, 30 preferred

Question 8

Temp is 32°F or below, ignition switch set to ignition after reaching…

Answer 8

50% N2

Question 9

APU START/STOP switch to START, tachometer accelerates to…

Answer 9

100% rpm

Question 10

APU EGT at ____ in GEN ONLY and ____ when in NORMAL MODE

Answer 10

800°F
1200°F

Question 11

N2 rollback, EGT rises. DONT USE FUEL FLOW AS A STALL INDICATOR

Answer 11

Sub-idle start stall

Question 12

No EGT rise by 10 sec

Answer 12

No-start

Question 13

EGT exceeds 725°F

Answer 13

Hot start

Question 14

EGT rise with no RPM increase

Answer 14

False start

Question 15

Light off with EGT increase, slow acceleration and RPM stabilization below ground idle

Answer 15

Hung start

Question 16

How long do you have to reach 20% N2?

Answer 16

30 sec

Question 17

Breakthrough fuel flow…

Answer 17

1000 PPH

Question 18

Advance throttle to start at _____ N2

Answer 18

20% N2 min-25% N2 max

Question 19

Fuel flow after placing throttle to start

Answer 19

300-680 PPH

Question 20

EGT indication after placing throttle to start within…

Answer 20

10 sec

Question 21

Oil press before throttle to start?

Answer 21

Positive pressure

Question 22

EGT at 40% N2

Answer 22

< 600C

Question 23

Operate engine at idle for _____ prior to advancing

Answer 23

5 min

Question 24

Advance throttle to idle at approx _____ N2

Answer 24

50% N2

Question 25

Place starter switch to OFF at _____ N2 (ignition below 32F)

Answer 25

50%

Question 26

Oil pressure at idle

Answer 26

13-35 psi

Question 27

N1 at idle

Answer 27

16%-22%

Question 28

N2 at idle

Answer 28

54%-62%

Question 29

Oil temp less than ____ at idle

Answer 29

160C

Question 30

Fuel flow at idle

Answer 30

400-800 PPH

Question 31

To shed ice, increase N1 to ________

Answer 31

35% then slowly to 70% for 15 sec

Question 32

Min HYD reservoir limit

Answer 32

2 GAL

Question 33

R and L hyd press gauges at idle

Answer 33

2850-3200 psi

Question 34

When should fuel boost pump switches be placed to off?

Answer 34

0% N2

Question 35

When should HYD PRESS switch be placed off?

Answer 35

0% N2

Question 36

APU GEN ONLY RPM

Answer 36

60% rpm

Question 37

APU Normal mode RPM

Answer 37

100%