Brainscape's Knowledge GenomeTM

Browse over 1 million classes created by top students, professors, publishers, and experts.


See full index

C Waste Water Management > Secondary Process & Troubleshooting Practice Questions > Flashcards

Secondary Process & Troubleshooting Practice Questions Flashcards

1
Q
  1. PROBLEM:
    Classic sludge bulking is occurring in the final clarifier of a conventional activated sludge plant. Indicators include: solids pouring over the weirs, excessive floc observed at the surface, and a homogenous (uniform) sludge blanket appearing throughout the clarifier. Sludge in settling test settles slowly leaving a cloudy supernatant. What is the MOST
    probable cause?
A

Young sludge

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q
  1. PROBLEM:
    Excessive white, billowing foam in the aeration tank surface.
    What is the MOST probable cause?
A

MLSS too low

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q
  1. What happens in the stabilization (re-aeration) tank in the contact-stabilization process?
A

Absorption and digestion of the waste material collected by microorganisms

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q
  1. PROBLEM:
    Good settling in the 30 minute settleability test. Excessive floc billowing in the clarifier
    and washing out. Sludge scrapers and RAS system appear normal
    What is the BEST solution to fix the problem?
A

Reduce clarifier hydraulic loading rates

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q
  1. PROBLEM:
    Classic sludge bulking is occurring in the final clarifier of a conventional activated sludge plant. Indicators include: solids pouring over the weirs, excessive floc observed at the surface, and a homogenous (uniform) sludge blanket appearing throughout the clarifier. Sludge in settling test settles slowly leaving a cloudy supernatant. What is the
    NECESSARY CHECK to confirm the cause?
A

Calculate the sludge age

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q
  1. In a well operated activated sludge plant, when the RAS flow rate is decreased but the WAS flow rate remains constant, the expected conditions would be
A

MLSS F/M Ratio MCRT

Decreases Increases Decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q
  1. In an activated sludge plant, if the DO in the aeration tank suddenly decreases and the aerators are not the problem, what is the MOST PROBABLE cause?
A

Increased organic load into tank

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

8
PROBLEM:
Upon arriving at the package treatment plant serving a small community, you find a uniform sludge blanket rising throughout the clarifier. A settleability test reveals a very slow settling sludge leaving a very clear supernatant. MLSS test results are normal, but a calculation of the SVI shows a high sludge volume index. What is the MOST likely cause of the high sludge blanket?

A

Filamentous bacteria are causing the slow settling

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q
  1. PROBLEM:
    Solids are washing out of the secondary clarifier of the activated sludge plant. Plant personnel increase the return activated sludge (RAS) flow rate, which slows the problem temporarily, but then it worsens after 30 minutes. What is the cause of the plant problem?
A

increasing the RAS decreased the detention time in the clarifier

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q
  1. PROBLEM:
    Solids are washing out of the secondary clarifier of the activated sludge plant. A
    settleability test shows good settling CAN occur. The MOST likely cause of the problem is:
A

High flows are entering the treatment plant

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q
  1. F/M Ratio can be BEST be described as:
A

The pounds of CBOD applied to a pound of MLVSS

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q
  1. PROBLEM:
    Small particles of ash-like (pinpoint floc) material floating on the clarifier surface.
    Denitrification is NOT the problem. What is the BEST solution?
A

If MLSS grease exceeds 15% by weight, repair or replace scum baffles and
implement industrial waste ordinance.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q
  1. A reduction of alkalinity across the secondary treatment process likely indicates
A

Nitrification is occurring

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q
  1. A microscopic exam shows a predominance of amoebae, flagellates with a few free swimming ciliates. The floc appears large and irregularly shaped and not very dense. What is the condition of the MLSS?
A

Under-oxidized and Young

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q
  1. Dark brown, almost gray/black sudsy foam on the aeration tank surface. Mixed liquor color is very dark brown, to almost black. There is the detection of a septic or sour odor in the area of the aeration tank. What is the MOST likely cause?
A

Anaerobic conditions are occurring in the aeration tank

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q
  1. Localized clouds of fluffy homogenous (uniform) sludge rising in certain areas of the clarifier. Mixed liquor settles slowly, and leaves stragglers in the supernatant of the settleometer. What is the NECESSARY CHECK to confirm the cause?
A

MLVSS, mg/L

17
Q
  1. Dark brown, almost gray/black sudsy foam on the aeration tank surface. Mixed liquor color is very dark brown, to almost black. There is the detection of a septic or sour odor in the area of the aeration tank. What is the BEST method to correct the problem?
A

Increase the air SCFM to maintain proper DO

18
Q
  1. The trickling filter plant is experiencing large amounts of filter flies and some offensive odors coming from the filters. Influent BOD and TSS are normal, and the weather is not a concern. What is the BEST METHOD to correct the problem?
A

Increase the recirculation flow rate

19
Q
  1. The effluent of the activated sludge plant is high in CBOD and ammonia. A microscopic exam shows a high amount of organism activity. If an oxygen uptake rate (OUR) test is run on the aeration tank effluent, the expected test result would
A

High OUR

20
Q
  1. There are small particles of ash-like material floating on the clarifier surface. The MOST likely cause is:
A

Denitrification is occurring in the clarifier

21
Q
  1. The aeration tank DO has been running normal (1.5 to 2.0 mg/L) the whole month. Todays DO reading has spiked to nearly 6.0 mg/L in the aeration tank, and the clarifier and plant effluent are cloudy. What is the MOST likely cause of the rise in DO?
A

A shock load of formaldehyde has entered the plant

22
Q
  1. The aeration tank DO has been running normal (1.5 to 2.0 mg/L) the whole month. Todays DO reading has spiked to nearly 6.0 mg/L in the aeration tank, and the clarifier and plant effluent are cloudy. This problem has occurred often in the past, and causes the plant to be out of compliance several times per year. What is the BEST METHOD to correct this problem?
A

Start and enforce sewer-use ordinances

23
Q
  1. A common problem with trickling filter operation is:
A

Excessive sloughing of biofilm causing ponding

24
Q
  1. A reason to switch to contact-stabilization mode of treatment would be:
A

To protect microorganisms from short-term toxic shock loads

25
Q
  1. The aeration tank is approaching under-loaded conditions (high MLSS) because of old sludge in the system. The expected conditions seen in the final clarifiers would be:
A

Pin floc

26
Q
  1. A common remedy for activated sludge system problems is to increase the waste activated sludge (WAS) flow rate. When would an increase of WAS rate NOT be correct?
A

When straggler floc is present in clarifier and settleometer

27
Q
  1. The terms under-oxidized and over-oxidized are used to describe what parameter?
A

Sludge age or MCRT

C Waste Water Management (5 decks)

Brainscape helps you reach your goals faster, through stronger study habits.
© 2024 Bold Learning Solutions. Terms and Conditions