Section2 URE

Question 1

Which of the following sampling devices is used for sampling pressurized systems under flow conditions?

Answer 1

In line sampler

Question 2

After obtaining a sample with an in line sampler how much time should be allowed to elapse before disassembling the sampler?

Answer 2

60 seconds

Question 3

What is the major cause of chemical contamination of fuel?

Answer 3

Carelessness

Question 4

Which of the following is not a light hydrocarbon contaminant that may be found in LOX?

Answer 4

Solvents

Question 5

Samples are taken from a LOX storage tank and sent to the area lab to be analyzed for purity, odor, and minor constituents every

Answer 5

90 days

Question 6

Unless otherwise specified, all samples of aviation fuels submitted to off base labs will be a minimum of

Answer 6

2 gallons

Question 7

What type of overpacking should no be used for samples of aviation fuels because of the potential for sample contamination?

Answer 7

Vermiculite

Question 8

What kind of dye if any is used to aid in distinguishing water from fuel during a visual sample?

Answer 8

Food coloring

Question 9

A 100 mesh strainer can remove particles that are

Answer 9

150 microns or larger

Question 10

Which recoverable and waste petroleum product category includes turbine engine oil?

Answer 10

Category 4

Question 11

At a minimum reclaimed product that has been returned to storage should be filtered how many times before re-issue to aircraft?

Answer 11

2

Question 12

The API gravity test is most accurate when the fuel temp is near

Answer 12

60 F

Question 13

What kind of cylinder is used to preform the API gravity test?

Answer 13

Graduated

Question 14

The correct place to take the reading for the API gravity test is at the

Answer 14

Point at which the principle surface of the liquid cuts the hydrometer scale

Question 15

Which testing method is the most accurate way to determine total solid content in a fuel sample

Answer 15

Bottle method

Question 16

Which of the following products is used to rinse new sample containers prior to use?

Answer 16

Filtered turbine fuel

Question 17

How often must electrical continuity tests be preformed on lab filtration equipment?

Answer 17

Monthly

Question 18

At what temperature are membrane filters dried prior to use for a bottle method test?

Answer 18

194F

Question 19

When performing a bottle method analysis on what type of fuel is a flow reducer ring not required?

Answer 19

JP5

Question 20

When conducting a field analysis for solids using color and particle assessment method, what device is used to remove residual fuel from a single filter monitor?

Answer 20

Metal syringe

Question 21

What type of dye is used for the AEL detector pad?

Answer 21

Sodium fluorescein

Question 22

How often should printed standards for the AEL test be replaced

Answer 22

Annually

Question 23

When should the gammon aqua glo water detector be calibrated?

Answer 23

Daily prior to the first use

Question 24

How much fuel should be allowed to pass through a filter separator vessel when obtaining a sample for fiber analysis?

Answer 24

2,000 gal

Question 25

All of the following may result in erroneous fiber analysis results except

Answer 25

Entrance of airborne fibers during analysis

Question 26

When cleaning sample bottles for use in fiber analysis how many times should the bottles be rinsed?

Answer 26

Twice

Question 27

Cleaning of the probe before conductivity testing is not required

Answer 27

When the conductivity meter can be zeroed with the probe attached.

Question 28

What type of container should not be used when obtaining conductivity samples?

Answer 28

Plastic

Question 29

Within how many minutes after sampling is it preferable to obtain a fuel conductivity reading?

Answer 29

2 minutes

Question 30

What is the maximum amount of time that can elapse between obtaining a conductivity sample and taking the reading?

Answer 30

24 hours

Question 31

When equipped with proper batteries the model 1152 conductivity meter is approved for use in

Answer 31

Hazardous locations

Question 32

What cleaning agent should be used to clean conductivity probes?

Answer 32

Isopropyl alcohol

Question 33

When performing a FSII analysis how long should the fuel/water mixture in the separatory funnel be shaken?

Answer 33

5 minutes

Question 34

During a flash point analysis what action must be taken if the sample flashes upon first application of the flame?

Answer 34

Preform new flashpoint test

Question 35

What percentage of wax does DF-2 contain?

Answer 35

6 to 8 precent

Question 36

To whom should a request for winter grade diesel fuel be submitted?

Answer 36

DESC

Question 37

Bases that experience cold weather problems should conduct cloud point analysis on all DF-2 received between what months?

Answer 37

October through march

Question 38

When entering analysis results in the BSM-E quality control module the amount of fuel obtained to preform the sample should be entered in which block?

Answer 38

SMPLE SIZE block

Question 39

Hat form is used as a temporary means of identifying conditions that could result in death, disability, or a lost work day?

Answer 39

AF form 979

Question 40

Who is responsible for coordinating the placement of danger tags with the appropriate agency?

Answer 40

Danger tag program monitor

Question 41

Verification of a RAC should be accomplished as soon as possible and should not exceed

Answer 41

10 days

Question 42

What form is used as a temporary means of warning personnel against potential hazards or to caution against unsafe practices

Answer 42

AF form 980

Question 43

All of the following situations would warrant QC hold except

Answer 43

A hose cart due for sample for solids

Question 44

Who within the fuels management flight is responsible for maintaining the keys to the QC hold box?

Answer 44

Fuels lab personnel

Question 45

Equipment on QC hold will not be used for servicing

Answer 45

Until lab have completed required samples with satisfactory results

Question 46

Who is responsible for reviewing lab reports and BSM-E data to identify significant trend patterns in fuel quality?

Answer 46

FISC superintendent

Question 47

Supply and equipment budget forecasts are coordinated through the FMT to the

Answer 47

Squadron commander

Question 48

Who within a fuels management flight is responsible for managing the GPC program

Answer 48

Fuels material control supervisor

Question 49

How long should documents received and or generated by a GPC cardholder to support transactions be retained?

Answer 49

36 months

Question 50

how often should GPC cardholders reconcile the statement of account via the banks electronic access system?

Answer 50

Monthly

Question 51

When making a telephone purchase GPC cardholders should inform vendors to include all of the following info on a shipping document except

Answer 51

GPC account number

Question 52

The fuels mobility supervisor works in conjunction with whom to ensure appropriate sei is awarded to personnel completing specialized training?

Answer 52

Fuels training supervisor

Question 53

Retrainees must meet all of the following requirements for award of the 5 skill level except

Answer 53

Completion of a minimum of 15 months on the job training

Question 54

What form is completed for skill level awards when all upgrade training is complete?

Answer 54

AF form 2096

Question 55

Core task waiver letters for active duty personnel should be approved by

Answer 55

MAJCOM

Question 56

How often should all training records be reviewed?

Answer 56

Semiannually

Question 57

What type of sampling device is primarily used to obtain samples from barrels for visual examination?

Answer 57

Drum thief