Tools/Testers

Question 0

What pliers should be used when cutting large gauge wires

Answer 0

Linemans side cutting pliers

Question 1

What are the two types of crossed screwdrivers

Answer 1

Phillips – Blunt

Reed and prince – sharp

Question 2

What is a center punch used for

Answer 2

A starting point

Question 3

What is a drift punch used for

Answer 3

Removing shaft pins and rivets

Question 4

What is a hole punch used for

Answer 4

Punching specific size holes

Question 5

How does a rotary punch work

Answer 5

Uses a wheel to determine size of hole

Question 6

How do you remove a hollow punch from a lead block

Answer 6

Twist out

Question 7

What are pinking shears used for

Answer 7

Keep material from fraying

Question 8

What are awls used for

Answer 8

Finding holes under fabric and punching holes in thick material

Question 9

What type of tool is used to install grommets

Answer 9

Punches and dies

Question 10

What are the parts of the snap fastener installation cents

Answer 10

Die cap
Die eyelet
Chuck socket
Chuck stud

Question 11

What is the advantage of the portable press

Answer 11

Can be used in tight spaces

Question 12

What does TMDE mean

Answer 12

test, measurement, and diagnostic equipment

Question 13

If a piece of TMDE has an expired inspection cycle is used what is the common assumption

Answer 13

its wrong and needs to be reinspected

Question 14

what are the common methods of annotating TMDE calibration due dates

Answer 14

AFTO 108 & 394 label

Question 15

What TO’s explain the TMDE progran and prescribe inspection intervals

Answer 15

33K-1-100-1 and 33K-1-100-2

Question 16

What are the 2 most common torque devices

Answer 16

beam and ratchet

Question 17

What setting should a torque wrench/screwdriver be on when not in use

Answer 17

the lowest

Question 18

When are torque devises used

Answer 18

when the TO says so

Question 19

When do you use a torque tool to loosen stuff

Answer 19

when the TO says so

Question 20

What do you do before you use a torque tool

Answer 20

check date and warm it up

Question 21

What test set allows you to verify the integrity of aircrew members fit while wearing the COMBAT EDGE ensemble

Answer 21

TTV-529/E pressure breathing flight ensemble test

Question 22

what tester is used to establish the release altitude of automatic parachute release mechanisms

Answer 22

automatic parachute ripcord tester

Question 23

What two methods the combined aircrew systems tester uses to measure leakage of a mask

Answer 23

dynamic and drop leaking

Question 24

what test set runs preprogrammed automatis systems test with user responses to on screen requirements

Answer 24

TS-4317-3 (RCTS-003)

Question 25

How is the Hoffman ANV-126 test set used at all service levels

Answer 25

operational- verify and test basic functoins | maintenance/depot- trouble shoot, support repair activities, and preform final test

Question 26

What does the multimeter measure

Answer 26

voltage, resistance, and continuity

Question 27

how do you identify socket sets by

Answer 27

driver size

Question 28

What are the two types of woodworking chisels

Answer 28

socket and tang

Question 29

What type of stone should be used to sharpen shears

Answer 29

fine to medium

Question 30

If measuring tape sags what does that do

Answer 30

increases measurement

Question 31

When useing an adjustable snap fastener press, what distance requred between the chuck and the die pin the press

Answer 31

1/32 of an inch

Question 32

What date format on TMDE item

Answer 32

julian

Question 33

What does COMBAT EDGE stand for

Answer 33

Combined Advanced Technology Enhanced Design "G" Ensemble

Question 34

What tester tests COMBAT EDGE equipment but requires a compressed air or oxygen cylinder

Answer 34

TTU-529/E

Question 36

Which tester uses a 9V battery as a power source

Answer 36

DMH-1 and multimeter

Question 37

What type of grommet is used for heavy duty applications?

Answer 37

Spurred.