ULTIMATE MASTERLIST Flashcards
(249 cards)
1
Q
Bidets DFU
A
2 DFU
2
Q
Clotheswashers DFU
A
2 DFU
3
Q
Dental Units or Cuspidors DFU
A
1 DFU
4
Q
Dental Unit or Cuspidor - Public (WSFU)
A
1 WSFU
5
Q
Bidet - Private (WSFU)
A
2 WSFU
6
Q
Urinal stall separate trap DFU
A
2 DFU
7
Q
Sink service DFU
A
3 DFU
8
Q
Urinal wall-mounted integral trap, trap arm only DFU
A
3 DFU
9
Q
Wash Sink, circular or multiple (each set of faucets) - Public (WSFU)
A
2 WSFU
10
Q
Shower, each head - Private (WSFU)
A
2 WSFU
11
Q
Bathtub DFU
A
2 DFU
12
Q
Water closet, private installation DFU
A
4 DFU
13
Q
Shower single stall DFU
A
2 DFU
14
Q
Sink, service - Public (WSFU)
A
4 WSFU
15
Q
Interceptors for sand, autowash, etc. DFU
A
6 DFU
16
Q
Flushometer tank - Public (WSFU)
A
5 WSFU
17
Q
Receptors (floor sinks), indirect waste receptors for refrigerators, coffee urns, water station, etc. DFU
A
1 DFU
18
Q
Bathtub - Public (WSFU)
A
4 WSFU
19
Q
Dental Lavatory - Public (WSFU)
A
2 WSFU
20
Q
Kitchen Sink - Private (WSFU)
A
2 WSFU
21
Q
Urinal wall-mounted blowout, integral trap DFU
A
6 DFU
22
Q
Receptors, indirect waste receptors for commercial sinks, dishwashers, air washers, etc. DFU
A
3 DFU
23
Q
Urinal stall - Public (WSFU)
A
5 WSFU
24
Q
Urinal wall-mounted washout DFU
A
2 DFU
25
Floor Drains DFU
2 DFU
26
Drinking Fountain - Private (WSFU)
1 WSFU
27
Mobile home park traps DFU
6 DFU
28
Flush Tank - Public (WSFU)
5 WSFU
29
Water closet, public installation DFU
6 DFU
30
Drinking Fountains DFU
1 DFU
31
Drinking Fountain - Public (WSFU)
2 WSFU
32
Urinal (wall lip) - Public (WSFU)
5 WSFU
33
Bathtub - Private (WSFU)
2 WSFU
34
Sinks, and/or dishwashers (residential) 51 mm min. waste DFU
2 DFU
35
Bidet - Public (WSFU)
4 WSFU
36
Sink, service - Private (WSFU)
2 WSFU
37
Lavatory - Public (WSFU)
2 WSFU
38
Wash basin in sets DFU
2 DFU
39
Flushometer Valve- Private (WSFU)
6 WSFU
40
Dental Lavatory - Private (WSFU)
1 WSFU
41
Sink bar commercial DFU
2 DFU
42
Kitchen Sink - Public (WSFU)
4 WSFU
43
Laundry Tray (1 or 2 compartments) - Public (WSFU)
4 WSFU
44
Urinal wall-mounted washdown or siphon jet DFU
2 DFU
45
Urinal pedestal, trap arm only DFU
6 DFU
46
Laundry Tray (1 or 2 compartments) - Private (WSFU)
2 WSFU
47
Combination Sink and Tray - Private (WSFU)
3 WSFU
48
Bedpan Washer - Public (WSFU)
10 WSFU
49
Sink flushing rim, clinic DFU
6 DFU
50
Shower, each head - Public (WSFU)
4 WSFU
51
Flush Tank - Private (WSFU)
3 WSFU
52
Flushometer Valve- Public (WSFU)
10 WSFU
53
Sink, commercial or industrial schools DFU
3 DFU
54
Sink bar private DFU
1 DFU
55
Urinal with Flush Tank - Public (WSFU)
3 WSFU
56
Lavatory - Private (WSFU)
1 WSFU
57
Urinal, pedestal - Public (WSFU)
10 WSFU
58
Interceptors for grease, oil, etc. DFU
3 DFU
59
Flushometer tank - Private (WSFU)
3 WSFU
60
Wash basin (lavatory) single DFU
1 DFU
61
The water shall be kept in the pipe system or in the portion under test for at least _____ minutes before inspection starts
15 minutes
62
In a water test, each section shall be filled with water, but no section shall be tested with less than _____ m head of water.
3
63
Where the local water pressure is in excess of _____ kpa, an approved-type pressure regulator preceded by an adequately sized strainer shall be installed to reduce the pressure on the building side of the regulator to the required supply pressure.
551
64
The corresponding maximum trap loading pipe size for fixture unit 6 (answer in mm)
76
65
Support trap arms in excess of _____ feet in length as close as possible to the trap.
3
66
Closet rings shall be tightly fastened with corrosive resistant fasteners up to the floor with top surface _____ mm above finish floor.
6.4
67
When disposal fields are installed, a minimum of _____ of trench bottom shall be provided for each system exclusive of any hard pan, rock, clay, or other impervious formations
14 sqm
68
When the quantity of sewage exceeds the amount that can be disposed in a _____ meter of each line, a dosing tank shall be used.
152.4 m
69
Backflow prevention for hot water over ____ deg. C shall be a listed type assembly.
43.3
70
Cast iron fittings up to and including _____ mm in size when used in connection with potable water piping shall be galvanized.
51
71
Interceptors for sand and similar heavy solids shall have a water seal of not less than _____ mm deep.
152
72
Trenches shall be back-filled in thin layers of _____ m
0.3
73
(Vertical wall areas for rainwater piping size) For two adjacent walls, add _____ percent of the total wall areas to the roof area.
35
74
Before placing filter material or drain lines in a prepared excavation, all smeared or compacted surfaces shall be removed from trenches by raking to a depth of _____ mm.
25.4 mm
75
Each grease trap shall have an approved water seal of not less than _____ mm.
51
76
Minimum thickness of lead safe pan in mm
1.6
77
Cleanout size of 64 mm pipe. (answer in mm)
64
78
Estimated sewage flow rate for airports per employee
56.8 LpD
79
Each run of pipe which is more than _____ m in total developed length shall be provided with a cleanout.
15
80
No standpipe receptor for any clotheswasher shall extend more than _____ m nor less than 0.45 m above its trap.
0.8
81
The inlet compartment of any septic tank shall be not less than _____ of the total capacity of the tank.
36925
82
The vacuum breaker shall be installed at the discharge side of the flushometer valve with the critical level at least _____ mm.
152
83
Retention time of commercial kitchen waste
2.5 hours
84
No underfloor cleanout in any residential occupancy shall be located more than _____ m from an access door, trap door or crawl hole.
6.1
85
All septic tank covers shall be capable of supporting an earth load of not less than _____ when the maximum coverage does not exceed 9m.
14.4 kpa
86
An exposed and readily accessible drawn brass tubing trap, not less than Gauge ___ may be used on fixtures discharging domestic sewage but shall exclude urine.
17
87
The minimum size of any pump discharge or any discharge pipe from a sump having a water closet connected thereto shall not be less than _____ mm diameter.
50.8
88
Water closets shall be computed as _____ fixture units when determining septic tank size.
6
89
Every abandoned building (house) sewer, or part thereof, shall be plugged or capped in an approved manner within _____ m of the property line.
1.5
90
The sand interceptor shall have a minimum dimension of _____ m^2 for the net free opening of the inlet section.
0.2
91
For flush tank supplies, the available pressure may not be less than _____.
55.16 kpa
92
Estimated sewage flow rate for Day Camps (no meals served)
56.8 LpD
93
(Septic Tank) The liquid depth shall be not less than ______ nor more than _____.
0.6 m to 1.8 m
94
The corresponding maximum trap loading pipe size for fixture unit 3 (answer in mm)
38
95
Restaurant kitchen and other special-use sinks may be made of approved-type bonderized and galvanized sheet steel of not less than Gauge No. _____.
16
96
When seepage pits are used in combination with disposal fields, the filter material in the trenches shall terminate at least _____ from the pit excavation.
1.5 m
97
Lead pipe shall be supported at intervals not exceeding _____ m at centers with a rigid vertical back-up.
1.2
98
Fixture outlets shall not be connected to the horizontal excreta drainage piping system within _____ m of any vertical to horizontal change of direction of a stack containing suds-producing fixtures.
2.4
99
When disposal fields and/or seepage pits are installed in sloping ground, the minimum horizontal distance between any part of the leaching system and ground surface shall be _____.
4.6 m
100
Where there is exposure to skin contamination with poisonous, infectious, or irritating materials, provide 1 lavatory for each _____ persons.
5
101
No part of the perimeter of the leaching bed shall be more than ____ from a distribution drain line.
0.9 m
102
Lead bends and lead traps shall not be less than ____ mm in wall thickness.
3.2
103
Wiped lead joints shall have an exposed surface on each side of a joint not less than _____ mm.
19
104
The diameter of an individual vent shall not be less than _____ mm nor less than 1/2 the diameter of the drain to which it is connected.
32
105
The public sewer may be considered as not being available when such public sewer or any exterior drainage facility connected thereto is located more than _____ m from any proposed building or exterior drainage facility on any lot or premises thereat.
61
106
Fixtures that also serves as a vent for not to exceed _____ fixtures.
4
107
The arch or dome of seepage pit shall be an approved type one or two piece reinforced concrete slab of ____ minimum compressive strength.
2500 psi
108
Side walls of the septic tank shall exceed at least _____ above the liquid depth.
228.6 mm
109
Each pressure relief valve shall be an approved automatic type with drain and each such relief valve shall be set at a pressure of not more than _____ kpa.
1033
110
Vertical vent pipes for outdoor installations shall extend to at least _____ m distant from any part of the roof that is used for other purposes.
3
111
The width of a continuous and indelibly colored stripe in copper tubing.
6.4 mm
112
Water pipes crossing sewer or drainage piping constructed of clay or materials, not approved for use within a building, shall be laid a minimum of _____ m above the sewer or drainpipe.
0.3
113
Interceptors shall be of approved design and be of not less than _____ compartments.
2
114
Distance of Building or structures to Building Sewer (answer in meters)
0.60 m
115
In an air test, the air is forced into the pipe system until there is a uniform gauge pressure of _____ kpa or sufficient to balance a column of mercury 254 mm in height
34.5
116
The distance to vent of a trap arm 51 mm in diameter. (answer in meters)
1.52
117
Distance of Septic Tank to to Water Supply wells.
15.2 m
118
If the highest group of the fixtures contains flushometer valves , the pressure for the group should not be less than _____.
103.42 kpa
119
A _____ kpa air pressure may be substituted for the water test.
344.5
120
Minimum depth of filter materials under drain lines
304.8 mm
121
The minimum wall thickness of any steel tank shall be _____ mm.
2.8 mm
122
An additional cleanout shall be provided on a horizontal line with an aggregate offset angle of direction exceeding _____ degrees.
135
123
Each vent pipe or stack through roof shall extend its flashing all around and the stack vent shall terminate vertically not less than _____ m above the roof.
0.15
124
The yoke vent connection with the vent stack shall be placed not less than _____ m above the floor level.
1
125
Allowable slope of a pipe having a diameter 203 mm or larger is _____%.
0.5
126
Access to each septic tank shall be provided by at least two manholes _____ in minimum dimension.
508 mm
127
Water pipes and fittings with a lead content that exceed ___% shall be prohibited and not used in potable piping systems.
8
128
Depth of equivalent area of rectangular gutter = ____ x diameter.
0.392
129
Cleanouts may be omitted on a horizontal drain line less than _____ m in length unless such line is serving sinks or urinals.
1.5
130
Each vent opening shall terminate not less than _____ m above any openable window, door opening, air intake or vent shaft.
0.9
131
Tunnels shall have a clear height of _____ m above the pipe and shall be limited in length to 1/2 the depth of trench, with a maximum length of 2.4 meters.
0.6 m
132
Water pipe joints shall be installed not less than _____ m away from sewer line in both directions.
3
133
Limit stops shall be provided on such valves and shall be adjusted to deliver hot water with a maximum temperature of _____ deg. C.
48.8
134
Storage factor for fully equipped commercial kitchen- 16 hours operation
2
135
How many tests cocks does a Double Check Valve Backflow Prevention Assembly have?
4
136
Each seepage pit shall have a minimum sidewall of _____ below the inlet.
3 m
137
Such tailpiece or connections shall be as short as possible and in no case shall exceed _____ m long.
0.6
138
The developed length between the trap of a water closet or similar fixture measured from the top of closet ring (closet flange) to inner edge of vent shall not exceed _____ m.
1.8
139
No galvanized wrought iron or galvanized steel pipe shall be used underground and shall be kept at least _____ mm above ground.
152
140
Distribution drain lines in leaching beds shall be more than ____ apart on centers.
1.8 m
141
Kitchen Sink (Water Supply)
13 mm
142
Urinal wall-mounted washdown or siphon jet (Trap arm size)
51 mm
143
Urinal wall-mounted washout, separate trap (Trap arm size)
38 mm
144
Lavatory (Water Supply)
10 mm
145
Interceptors for grease, oil, etc. (Trap arm size)
51 mm
146
Clotheswashers (Trap arm size)
51 mm
147
Urinal Stall (Water Supply)
19 mm
148
Bidet (Water Supply)
13 mm
149
Drinking Fountain (Water Supply)
10 mm
150
Sinks and/or dishwashers (residential) 51 mm min. waste (Trap arm size)
38 mm
151
Sinks, service (Trap arm size)
51 mm
152
Laundry tubs (Trap arm size)
38 mm
153
Bidets (Trap arm size)
38 mm
154
Wash basin (lavatory) single (Trap arm size)
32 mm
155
Interceptors for sand, autowash, etc. (Trap arm size)
76 mm
156
Water Closet public installation (Trap arm size)
76 mm
157
Water Closet Flushometer tank (Water Supply)
10 mm
158
Receptors, indirect waste receptors for commercial sinks, dishwashers, air washers, etc. (Trap arm size)
51 mm
159
Sinks flushing rim, clinic (Trap arm size)
76 mm
160
Sinks bar private (Trap arm size)
38 mm
161
Urinal wall-mounted, integral trap, trap arm only (Trap arm size)
51 mm
162
Sinks bar commercial (Trap arm size)
38 mm
163
Dental Units or Cuspidors (Trap arm size)
32 mm
164
Dental Unit or Cuspidor (Water Supply)
10 mm
165
Service Sink (Water Supply)
13 mm
166
Sinks commercial or industrial, schools, etc. (Trap arm size)
38 mm
167
Laundry Tray 1 or 2 compartments (Water Supply)
13 mm
168
Dental Lavatory (Water Supply)
13 mm
169
Mobile Home Park Traps (Trap arm size)
76 mm
170
Wash sink, circular or multiple, each set of faucets (Water Supply)
13 mm
171
Bedpan Washer (Water Supply)
25 mm
172
Bathtub (Water Supply)
13 mm
173
Urinal wall-mounted, blowout, integral trap, trap arm only (Trap arm size)
76 mm
174
Urinal wall lip (Water Supply)
13 mm
175
Floor Drains (Trap arm size)
51 mm
176
Shower, each head (Water Supply)
13 mm
177
Shower, gang (Trap arm size)
51 mm
178
Water Closet Flushometer valve (Water Supply)
25 mm
179
Urinal stall (Trap arm size)
51 mm
180
Wash basin, in sets (Trap arm size)
38 mm
181
Combination Sink and Tray (Water Supply)
13 mm
182
Urinal Pedestal (Water Supply)
25 mm
183
Water Closet private installation (Trap arm size)
76 mm
184
Bathtubs (Trap arm size)
38 mm
185
Drinking Fountains (Trap arm size)
31 mm
186
Receptors (floor sinks) indirect waste receptors for refrigerators, coffee urns, water stations, etc. (Trap arm size)
38 mm
187
Urinal pedestal (Trap arm size)
76 mm
188
Water Closet Flush tank (Water Supply)
10 mm
189
Shower, single stall (Trap arm size)
51 mm
190
Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems
ASTM F2389
191
Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings
ASTM A126
192
National Building Code of the Philippines (Old)
RA 6541
193
Civil Engineering Law (Old)
RA 544
194
Standard for the Fire Protection of Information Technology Equipment
NFPA 75
195
Standard for the Fire Protection of Telecommunications Facilities
NFPA 76
196
An Act to Regulate the Practice of Architecture in the Philippines (Old)
RA 545
197
Standard for the Installation of Standpipe and Hose Systems
NFPA 14
198
Fire Code
NFPA 1
199
Accessibility Law
BP 344
200
Sanitary Engineering Law
RA 1364
201
Philippine Clean Air Act of 1999
RA 8749
202
Provincial Water Utilities Act of 1973
PD 198
203
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D3350
204
Code on Sanitation of the Philippines
PD 856
205
Liquefied Petroleum Gas Code
NFPA 58
206
Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
NFPA 211
207
Standard Specification for Seamless Red Brass Pipe, Standard Sizes
ASTM B43
208
Philippine Environment Code
PD 1152
209
National Building Code of the Philippines (Current)
PD 1096
210
Standard on Types of Building Construction
NFPA 220
211
Standard for the Installation of Air-Conditioning and Ventilating Systems
NFPA 90A
212
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Schedules 40, 80, and 120
ASTM D1785
213
Waterways Encroachment
PD 296
214
Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM A123
215
Electric Code
NFPA 70
216
New Electrical Engineering Law
RA 7920
217
Philippine Mechanical Engineering Act of 1998
RA 8495
218
Plumbing Law
RA 1378
219
Fire Code of the Philippines (Old)
PD 1185
220
National Fuel Gas Code
NFPA 54
221
Health Care Facilities Code
NFPA 99
222
Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR)
ASTM F442
223
Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
ASTM F441
224
Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment
NFPA 720
225
Standard on Continuity, Emergency and Crisis Management
NFPA 1600
226
Standard Specification for Seamless Copper Water Tube
ASTM B88
227
Water Code of the Philippines
PD 1067
228
Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems
ASTM D2846
229
Standard for the Installation of Stationary Pumps for Fire Protection
NFPA 20
230
National Fire Alarm and Signaling Code
NFPA 72
231
Standard for Emergency and Standby Power Systems
NFPA 110
232
Standard for Portable Fire Extinguishers
NFPA 10
233
Philippine Clean Water Act of 2004
RA 9275
234
Creation of the Professional Regulation Commission
PD 223
235
Civil Code of the Philippines
RA 386
236
Standard for Fire Safety and Emergency Symbols
NFPA 170
237
Fire Code of the Philippines of 2008
RA 9514
238
Standard Specification for Seamless Brass Tube
ASTM B135
239
Standard Method of Test for Temper of Strip and Sheet Metals for Electronic Devices (Spring-Back Method)
ASTM F155
240
Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes
ASTM A312
241
Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
ASTM A194
242
Flammable and Combustible Liquids Code
NFPA 30
243
Standard for the Inspection, Testing, and Maintenance of Water-based Fire Protection Systems
NFPA 25
244
Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
ASTM A53
245
Standard Specification for PVC Sewer Pipe and Fittings
ASTM D2729
246
Life Safety Code
NFPA 101
247
Standard for the Installation of Private Fire Service Mains and their Appurtenances
NFPA 24
248
Standard for the Installation of Sprinkler Systems
NFPA 13
249
Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
ASTM A888
