CIDQ Official Practice Test

Question 1

Which of the following is the MOST important consideration in planning for a small open office project?

Management of overall cost per square foot
Specification of appropriate materials and finishes
Maintaining ratio between circulation and work area
Support of job function and relationships

Answer 1

Support of job function and relationships

Question 2

When beginning a schematic floor plan for an existing building, what is the MOST effective sequence of adding spaces to the plan?

Building core, largest spaces, general circulation, public spaces, then other room allocations

Building core, public spaces, largest spaces, other room allocations, then general circulation

Public spaces, general circulation, largest spaces, other room allocations, then building core

Largest spaces, other room allocations, general circulation, public spaces, then building core

Answer 2

Building core, largest spaces, general circulation, public spaces, then other room allocations

Question 3

A client would like to install a window in a 60-minute rated door in a corridor. Which of the following would be acceptable?

10” x 10” [250 mm x 250 mm] wired glass
6” x 12” [150 mm x 300 mm] wired glass
10” x 10” [250 mm x 250 mm] tempered glass
6” x 12” [150 mm x 300 mm] tempered glass

Answer 3

10” x 10” [250 mm x 250 mm] wired glass

Question 4

Which of the following is a characteristic of a halogen lamp?

Easy to install and maintain
Cannot be dimmed
Requires a transformer at the switch
Brighter than other incandescent sources

Answer 4

Brighter than other incandescent sources

Question 5

What type of carpet construction has no separate primary backing?

Knitted
Woven
Tufted
font-default-tick Fusion-bonded

Answer 5

Woven

Question 6

Which of the following documents are MOST likely to be included in the design development package?

Technical drawings, schedules, and specifications required to price, build, and install the work

Any documents required to communicate compliance with applicable codes to local authorities responsible for issuance of permits

Technical drawings, images, and samples communicating design intent and client requirements

Detailed floor plans, ceiling plans, elevations, sections, design details, millwork drawings, and material samples and specifications

Answer 6

Detailed floor plans, ceiling plans, elevations, sections, design details, millwork drawings, and material samples and specifications

Question 7

When are three-dimensional studies MOST useful in the design process?

In the final contract document presentation
During the programming phase
As a rough sketch during the schematic stage
Throughout the entire design process

Answer 7

Throughout the entire design process

Question 8

When presenting the preliminary design and design concept of an office space to a client, what information should be included?

Preliminary floor plan, orthographic drawings, and rendered perspectives

Bubble diagrams, preliminary floor plan, and conceptual sketches

Dimensioned floor plan, orthographic drawings, and sample boards

Bubble diagrams, conceptual sketches, and sample boards

Answer 8

Bubble diagrams, preliminary floor plan, and conceptual sketches

Question 9

Which of the following is MOST important to include when preparing documents for the schematic presentation to the client?

Zoning diagrams
Stacking diagrams
Blocking plans
Floor plans

Answer 9

Floor plans

Question 10

What should be done before starting schematic design work on an office renovation with no existing electronic plans?

Develop program, field verify and document existing conditions
Obtain the original drawings, field verify and document existing conditions
Obtain the original drawings, develop construction documents
Develop preliminary plan, establish project budget

Answer 10

Obtain the original drawings, field verify and document existing conditions

Question 11

The difference between a precedent study and a case study is that the case study:

refers to a social aspect of a project.
refers to a project utilizing the newest theories.
has not been realized in physical form.
refers to an innovation in design.

Answer 11

refers to a social aspect of a project.

Question 12

What is identified in a precedent study?

The design solution
New building sites
Programmatic needs
Design team members

Answer 12

Programmatic needs

Question 13

Which aspect of lighting design should be addressed FIRST?

Lighting concepts using preliminary plans
Daylighting opportunities in the design
Reflected ceiling plans and details
Lighting control locations and circuiting

Answer 13

Daylighting opportunities in the design

Question 14

In terms of occupant health, which of the following lamp types is BEST for use in a bedroom?

LED lamp
Fluorescent lamp
Incandescent lamp
Clear mercury vapor lamp

Answer 14

Incandescent lamp

Question 15

Which of the following is a coordinator of voluntary standards development?

UL
ASTM
ANSI
ASHRAE

Answer 15

ANSI

Question 16

What method would the designer use to evaluate materials and finishes for a project without knowledge of the building standard lighting temperature?

Specify new light fixtures throughout to best match the materials and finishes
Evaluate the materials with two light sources of different spectral character
Evaluate the materials outdoors under direct sunlight
Request that all of the fixtures be re-lamped for consistent color temperature

Answer 16

Evaluate the materials with two light sources of different spectral character

Question 17

What is the MINIMUM required lighting level for a path of egress in a commercial space?

1 foot-candles (11 lux)
5 foot-candles (54 lux)
10 foot-candles (108 lux)
15 foot-candles (161 lux)

Answer 17

1 foot-candles (11 lux)

Question 18

Which specification type is used when documenting a custom reception desk, with specific fabrication, materials, and installation methods?

Reference
Performance
Descriptive
Proprietary

Answer 18

Descriptive

Question 19

When dimensioning a stair section what must be called out to make sure the stair is built to code?

Handrail height
Nosing radius
Stair width
Landing size

Answer 19

Handrail height

Question 20

During which design phase would an interior designer start an outline specification?

Design development
Schematic design
Contract documentation
Contract administration

Answer 20

Schematic design

Question 21

Upon completion of the following tasks, what should the interior designer do NEXT? • Interview client. • Obtain architectural drawings. • Conduct a site inspection. • Prepare preliminary sketches. • Evaluate existing furniture for continued use.

Review sketches and furniture layouts with your design firm’s owner.

Review preliminary specifications with the manufacturer’s representatives.

Present choices to the client’s purchasing department.

Note dimensional discrepancies on the architectural drawings.

Answer 21

Review preliminary specifications with the manufacturer’s representatives.

Question 22

What code deficiency exists in the accompanying drawing depicting an entrance door to a 1,500 sf [140 m2] suite, a corridor, and an exit stair door in a five-story office building?

The suite entrance door is too close to the fire exit.

The exit stair door is not equipped with quick release (panic) hardware.

A dampered duct opening is located in the exit stair wall.

Exit signage should be beside, not over, the exit door.

Answer 22

A dampered duct opening is located in the exit stair wall.

Question 23

In which space is emergency lighting REQUIRED?

Elevators
Private offices
Egress corridors
Restrooms

Answer 23

Egress corridors

Question 24

What has the GREATEST positive impact on life safety in an open office?

Heat detection
Operable windows
Building egress
Fire equipment location

Answer 24

Building egress

Question 25

The typical chronological order of system installation in new commercial construction is:

HVAC, Plumbing, Electrical
Electrical, Plumbing, HVAC
Plumbing, HVAC, Electrical
Electrical, HVAC, Plumbing

Answer 25

Plumbing, HVAC, Electrical

Question 26

Which of the following has the GREATEST impact on the effectiveness of an HVAC system?

Rooftop chiller size
Wall insulation type
Window treatments
Occupancy load

Answer 26

Occupancy load

Question 27

What is the result of withholding external fresh air from an HVAC system?

Unit efficiency is diminished
VOC build-up becomes more concentrated
Electrostatic filters are required
Condensation builds up in the ducts

Answer 27

VOC build-up becomes more concentrated

Question 28

A final construction budget for an office remodeling project is 10% higher than the client anticipated. What strategy would be MOST effective in lowering the costs?

Ask the contractor to use less expensive substitutes.
Select less expensive finish materials.
Reevaluate the area requirements with the client.
Create a new, simpler space plan.

Answer 28

Select less expensive finish materials.

Question 29

What method of scheduling, ideal for small projects of low complexity, indicates each team member’s responsibility and the projected timeline for each task from initiation to its completion?

Preemptive
Shared
Milestone
Critical path

Answer 29

Milestone

Question 30

Why are addenda issued?

To provide additional information not included in the bid package
To inform potential bidders about acceptable alternates
To obtain additional information
To request a change during construction

Answer 30

To provide additional information not included in the bid package

Question 31

Who is responsible for specifying and indicating heat detector devices on the drawings for a classroom project?

Fire-protection Engineer
Interior Designer
Electrical Engineer
Architect

Answer 31

Fire-protection Engineer

Question 32

What is the MINIMUM width required for a bedroom that is 10 ft. [3.05 m] long?

6 ft. [1.83 m]
7 ft. [2.13 m]
8 ft. [2.44 m]
9 ft. [2.74 m]

Answer 32

7 ft. [2.13 m]

Question 33

The occupancy load threshold requiring an increase from two to three egress doors per story is:

100
250
300
500

Answer 33

500

Question 34

A textile drapery intended for use on walls in a new concert hall must pass which standard test?

NFPA 269
NFPA 286
ASTM D6413
ASTM E2257

Answer 34

ASTM D6413

Standard Test Method for Flame Resistance of Textiles (Vertical Test)

Question 35

An Interior Designer is finishing a basement for a client and her family that includes a game room, 3/4 bathroom, laundry room, a bedroom, and the mechanical room for the home. The overall unfinished ceiling height is 8’-6” (2590.8 mm) and the home is forced-air, wood frame construction built in the late 20th-century. What would be the most appropriate wall and ceiling construction assembly in the basement?

Gypsum board ceiling throughout, walls to the underside of the sub-floor above, with acoustical batting

Combination of gypsum board and suspended acoustical tile ceilings, insulated walls to the finished ceiling height

Suspended acoustical tile ceiling, insulated walls to the underside of the sub-floor above

Combination of gypsum board and suspended acoustical tile ceilings, insulated walls to the underside of the sub-floor above

Answer 35

Combination of gypsum board and suspended acoustical tile ceilings, insulated walls to the underside of the sub-floor above

Question 36

Which of the following architectural elements can contribute to a daylighting strategy?

Flat white paint
Exposed concrete floor
Low-emissivity glass
Insulation with high R values

Answer 36

Low-emissivity glass

Question 37

When evaluating a systems furniture solution for a client who prefers wide aisles, which characteristic of the system will be MOST critical to achieve the desired aisle width?

Height of panels
Thickness of panels
Length of power
Material of panels

Answer 37

Thickness of panels

Question 38

When specifying the installation of ceramic tile, which of the following is required?

Sealant
Adhesive
Reducer Strip
Anti Fracture Membrane

Answer 38

Adhesive

Question 39

What is the minimum DCOF (Dynamic Coefficient of Friction) required for tile located in a public space?

0. 42
1. 57
2. 58
3. 60

Answer 39

0.42

Question 40

When a client brings their preferred furniture dealer as part of the project team, what should the designer do to coordinate their efforts?

Coordinate with the Architect and Structural Engineer

Coordinate with the general contractor to schedule furniture delivery

Answer requests for information (RFI’s) on the furniture bid package

Request that all correspondence go through the project manager

Answer 40

Coordinate with the general contractor to schedule furniture delivery

Question 41

Which casework grade would be MOST appropriate to specify base cabinets in an elementary school classroom?

Utility
Custom
Premium
Economy

Answer 41

Custom

Question 42

Construction documents generally undergo coordination review at which percentage of completion milestones?

50% and 90%
25% and 75%
30% and 60%
50% and 75%

Answer 42

50% and 90%

Question 43

A client needs to move into their space as soon as it is substantially complete and the furniture is installed. What is the MOST important task for the contractor to complete?

Punch list (deficiency list)
Post occupancy evaluation
Application for payment
Certificate of occupancy

Answer 43

Punch list (deficiency list)