Basic Rigging Flashcards

(35 cards)

1
Q

If a sling leg is attached to a suspended load at an angle of less than 90”, the horizontal force acting on the sling leg

A

Increases as the sling angle gets smaller

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

both ends of a sling are attached to the hoist hook and a load is suspended from the center of the sling, what hitch is being used?

A

Basket

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Determine the weight of a load consisting of 100 brass rods, 6 ft. long and 1.5 inches in diameter. (The weight per linear foot is 6.51 lb.)

A

3906 LB

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

If a rope has a breaking strength of 25,000 Lb and the design factor of the sling is 5, what is the maximum allowable load they can lift?

A

5000 lb

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The purpose of the latch on a hoist hook is to

A

Retain the sling

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The following factors all affect wire-rope strength. In which one is the Did ratio important?

A

Bending over a curved surface

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Which of these wire-rope end fittings is the most efficient (assuming all are prepared correctly)?

A

Speitered socket|

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The letters FC, as part of a wire rope designation, stand for

A

Fiber core

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Which of the following is used to protect a rope loop from abrasion and sharp bends?

A

Thimble

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The length of wire rope between loops or end fittings of braided wire-rope slings should be a minimum of
_______times the diameter of the component wire rope.

A

10

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

The specification for welded-link chain that corresponds to a wire rope’s rated load is called the chain’s

A

Working Load limit

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Chain slings should be visually inspected_____ before and while using them.

A

daily

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Heavy-duty metal mesh is designated as______ gauge

A

10

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

An advantage of metal mesh slings is that they

A

conform to irregutarty shaped loads

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The standard minimum design factor for metal-mesh slings

A

5

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

fiber-rope sling should be removed from service if it

A

Shows kinking

17
Q

The highest grade of manila rope is known as

18
Q

Bending a load-bearing rope at a sharp angle can_____ its strength by as much as____%

19
Q

A splice of any type in a fiber rope reduces its strength by about____%

20
Q

Synthetic webbing is spliced by

21
Q

Wire rope should be removed from hoist service if the rigger finds

A

Two broken wires at a socketed end titing

22
Q

Overwrapping can throw a hoist’s stopping point out of adjustment if a____ limit switch is used.

23
Q

A top-running crane with a bridge beam supported on legs is called a____crane

24
Q

When conducting daily hoist and crane inspections, check limit switches with______and at____speed

25
Hoist load chain and sling chain
look similar
26
In a crane operation involving several people,
The operator must respond to a "stop" signal from anyone
27
When working with floor-operated hoists and cranes, you should make sure that (the)
obstructions can be avoided by the moving load
28
One edge of the load serves as a pivot during_____ turning
One-hook
29
When should blocks or other holding devices be placed at the location where a load will be set?
Before the load is lifted
30
In general, you should not use a hoist or crane to pull a load, but it is permissible if you
use a manual chain host in a horizontal setup
31
The height of a movable sectional metal scaffold that measures 4 x 8 ft at the base should not exceed _____ft
16
32
When you secure a scaffold with guy wires, what accessories do you use to tighten the wires to the correct tension?
Tumbuckles
33
A wooden ladder must NOT be coated with
Paint
34
Guy wires give the most support when they are positioned at a _____ angle to the vertical
45
35
If you inspect an aluminum ladder and find one cracked rung, you should
repair the rung immediately