Book 3: Unit 8 - Review: Chapter 19 - 20

Question 1

With regard to written communication, the acronym “PFD” mean
Select one:

a. Process flow description

b. Process flow diagram

c. Plumbing fixture diagram

d. Piping fixture drawing

Answer 1

b. Process flow diagram

Question 2

On P&IDs, the letters “NO” and “NC” are often found beside

Select one:

a. Controller symbols

b. Valve symbols

c. Pressure transmitter symbols

d. Flow indicator symbols

Answer 2

b. Valve symbols

Question 3

One of the main advantages of verbal communication is:

Select one:

a. There is a permanent record of the communication

b. It takes longer to process the wording than written communication

c. Talking to people the other side of the office

d. Immediate feedback and clarification

Answer 3

d. Immediate feedback and clarification

Question 4

One of the acceptable practices of single line sketches:

Select one:

a. Included as part of the trainee competent qualification sign-off requirements

b. Hand written notes are used instead of Standard Operating Procedure (SOP)

c. Used instead of the P&IDs and PFDs

d. Used as the official verification process for P&IDs and PFDs

Answer 4

a. Included as part of the trainee competent qualification sign-off requirements

Question 5

One of the typical details shown in the Process Flow Diagram (PFD) includes:

Select one:

a. Detailed pipe sizes

b. Main piping and direction of flow

c. Detailed configuration and exact location of equipment

d. All valve locations and orientation

Answer 5

b. Main piping and direction of flow

Question 6

The letters LAL inside a circle on a P&ID stands for

Select one:

a. Level alarm low

b. Level recorder

c. Level alarm high

d. Level glass

Answer 6

a. Level alarm low

Question 7

The symbol [shown below] is used in electrical diagrams to indicate a:

Select one:

a. Transformer

b. Knife switch

c. A ground

d. A normally open contact

Answer 7

c. A ground

Question 8

Single line sketches are used for:

Select one:

a. Official job instructions

b. Detailed plant process flow including equipment

c. Official plant process flow diagram and P & ID

d. Learning purposes completed with personalized written notes

Answer 8

d. Learning purposes completed with personalized written notes

Question 9

If you understand instructions given over a two-way radio, you should respond with
Select one:

a. “Affirmative”

b. “Loud and Clear”

c. “Over and Out”

d. “Roger That”

Answer 9

d. “Roger That”

Question 10

One of the main advantages of written communication is:

Select one:

a. The subject line can say it all

b. That it can be proof read and edited

c. It can be delivered in the shortest time

d. Immediate feedback from the recipients

Answer 10

b. That it can be proof read and edited

Question 11

One of the commonly accepted document control best practices is to:

Select one:

a. Store controlled documents in multiple locations

b. Have limited circulation of printed copies

c. Securely stored documents in the personal drive of the designated document control officer

d. Keep outdated documents for future reference

Answer 11

b. Have limited circulation of printed copies

Question 12

A piping and instrumentation diagram (P&ID) will show major flow lines:

Select one:

a. with most instrumentation

b. with all information for those lines

c. only with line size and major valves

d. with basic information for those lines

Answer 12

b. with all information for those lines

Question 13

The symbol [shown below] is used in P&ID diagrams to indicate a:

Select one:

a. Globe valve

b. Plug valve

c. Gate valve

d. Check valve

Answer 13

d. Check valve

Question 14

If your plant maintenance department neglects oil changes, filter replacement, and bearing lubrication, your plant will eventually need more unscheduled ___________ maintenance.

Select one:

a. Routine

b. Project

c. Emergency

d. Preventative

Answer 14

c. Emergency

Question 15

A process flow diagram (PFD) shows:

Select one:

a. The physical layout of equipment

b. All instrumentation

c. All the equipment in a plant

d. Major piping to do with a process

Answer 15

d. Major piping to do with a process

Question 16

An electrical diagram will show:

Select one:

a. The number and size of wires required

b. The basic power flow to each item

c. The exact location of each item in a building

d. The type of load at each item

Answer 16

b. The basic power flow to each item

Question 17

One of best practices for writing SOPs is to:

Select one:

a. Use a standardized template

b. Use text based format only

c. Put it to use as soon as it is written

d. Allow all workers an opportunity to write a SOP

Answer 17

a. Use a standardized template

Question 18

Which form of communication is preferred in the workplace?

Select one:

a. Personal

b. Verbal

c. Written

d. Radio

Answer 18

c. Written

Question 19

One of the main advantages of written communication is:

Select one:

a. It reduces the possibility of misinterpretation

b. It can be delivered in the shortest time

c. Immediate feedback from the recipients

d. The subject line can say it all

Answer 19

a. It reduces the possibility of misinterpretation

Question 20

The symbol [shown below] is used in P&ID diagrams to indicate a:

Select one:

a. Gate valve

b. Check valve

c. Plug valve

d. Globe valve

Answer 20

c. Plug valve