Part 2: Principles of Flight Flashcards

1
Q

What is Newton’s 3rd Law?

A

To every action, there is an equal and opposite reaction.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What is Bernouili’s Principle?

A

As airspeed increases, air pressure decreases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

in straight and level flight at constant speed, which forces are in balance?

A

Weight = Lift; Thrust = Drag

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What is the angle of attack of a wing?

A

The angle between the chord line of the wing and the oncoming air

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Where does air flow faster around a wing?

A

Over the top

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

How much lift is generated by the top of the wing?

A

Up to 80%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Where is the greatest effect of lift on the wing?

A

Nearer the front edge of the wing

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the relationship between air flow and lift?

A

Lift is at 90 degrees to air flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

How does drag vary in relation to airspeed?

A

The square of airspeed: 2 x airspeed = 4 x drag

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What are the three planes of movement?

A

lateral, longitudinal, normal

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What controls a plane’s pitch?

A

Elevators

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What controls a plane’s roll?

A

Ailerons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What controls a plane’s yaw?

A

Rudder

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What are dihedral wings?

A

Wings angled upwards (to create lateral stability)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are anhedral wings?

A

Wings angled downwards

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What do trimming tabs do?

A

Cancel out forces on flight controls

17
Q

What do flaps do?

A

They adjust lift and drag created by a wing (by changing its shape)

18
Q

What degree of flap give the best increase in lift?

A

30-60 degrees

19
Q

What degree of flap gives maximum drag?

A

90 degrees

20
Q

What are slats?

A

At front of wing, reduce stalling speed

21
Q

What is the critical angle of attack?

A

15 degrees (after this stalling is likely)

22
Q

What forces act on a glider?

A

Weight, drag and lift

23
Q

How does a glider speed up?

A

Lowers the nose

24
Q

How does a glider slow down?

A

Using airbrake

Suggested better answer by Katie Nixon:

A glider slows down by pitching nose up (using airbrakes only increases the rate of descent)

25
What control makes a helicopter produce lift?
Collective pitch control
26
What control makes a helicopter move forwards/backwards and side to side?
Cyclic pitch control
27
What undesirable effect is generated by helicopter rotor blades?
Torque reaction
28
What counters the torque reaction in helicopters?
Rudder pedals
29
What control makes a helicopter rotate?
Rudder pedals
30
What is angle A?
The angle of attack
31
Where is air pressure lowest?
At point B (where airflow is the fastest)
32
What is this aircraft doing?
Pitching
33
What is this aircraft doing?
Rolling
34
What is this aircraft doing?
Yawing
35
What is happening in the bottom diagram?
The plane is stalling (note angle of attack is 16 degrees, one degree more than the "critical" angle of attack).
36
This diagram shows a plane pitching, rolling and yawing + their controls. These are done across which three axis?
Pitching across the lateral axis. Rolling across the longitudinal axis. Yawing across the normal (or vertical) axis.
37
The diagram shows the three axes. What is movement across each of these called?
Movement across longitudinal axis = rolling. Movement across lateral axis = pitching. Movement across normal axis = yawing.