Safety, tools and PDI

Question 1

What is Bill C-45?

Answer 1

Federal legislation that protects you and your co-workers and prescribes criminal charges where a workplace injury or fatality occurs

Question 2

What is the angle of a cold file?

Answer 2

60 degrees

Question 3

What angle of the cutting lip of a drill bit?

Answer 3

59 degrees

Question 4

What should be the clearance angle of a drill bit?

Answer 4

12 degree

Question 5

What is the angle of a proper propane flare?

Answer 5

45 degrees

Question 6

What are colour aviation snips are for which cutting direct?

Answer 6

Yellow-straight
Green-right
Red-left

Question 7

What type of tanks can spin fittings be used on?

Answer 7

Polyethylene tanks

Question 8

How far should the table saw be above the material?

Answer 8

3/8”

Question 9

What is the maximum distance the tool rest should be from the grinding stone?

Answer 9

1/8”

Question 10

What is a jointer used for?

Answer 10

Used to straight or True one edge or surface

Question 11

What are sockets identified by?

Answer 11

Fastener size
Drive size
Socket depth
Number of points
Impact or hand socket

Question 12

How are hacksaw blades identified by?

Answer 12

Identified by 8, 10, and 12 inch lengths

and number of teeth per inch

Question 13

What should be your average cutting speed?

Answer 13

Approximately 50 strokes per minute

Question 14

How do you measure a file?

Answer 14

From heel to point not including tang

Question 15

How is a drill press sized?

Answer 15

By the distance between the post and the Center of the chuck

Question 16

What is a thickness planer used for?

Answer 16

Used to reduce thickness

Question 17

How is a router sized?

Answer 17

Sized by motor horsepower

Question 18

Things to remember when using router bits?

Answer 18

Deep cuts may require multiple passes

Question 19

What is the formula for calculating torque?

Answer 19

Torque = Force X Distance

Question 20

What are the numbers and colours of Robertson screwdrivers?

Answer 20

#0 Robertson: Yellow
#1 Robertson: Green
#2 Robertson: Red
#3 Robertson: Black

Question 21

What is GVW?

Answer 21

Gross vehicle weight

-the actual weight of the loaded vehicle

Question 22

What is GAW

Answer 22

Gross axle weight

-actual weight of the loaded vehicle carried by each axle

Question 23

What is GAWR

Answer 23

Gross axle weight rating

-maximum weight per axle

Question 24

What is GCWR?

Answer 24

Gross combined weight rating

-maximum weight allowed

Question 25

What is GVWR?

Answer 25

Gross vehicle weight rating | -maximum weight allowed by the vehicle manufacturer

Question 26

What size fire extinguisher should a trailer and motor home have? And where should it be located?

Answer 26

Trailers- 5 pound Motor homes- 10 Must be within 24" of the main entrance

Question 27

Where can a VIN be found?

Answer 27

May be found on: door pillar, trailer tongue, ID plate on the trailer exterior, or in an interior cabinet

Question 28

How are hammers sized?

Answer 28

By weight

Question 29

How are pliers sized?

Answer 29

By length

Question 30

Where can you find the best information about motor home controls?

Answer 30

In the owners manual

Question 31

What is required when there is propane on board

Answer 31

A LP detector

Question 32

What is required in required by law in every trailer, camper, or motorhome?

Answer 32

A Co detector, and a smoke detector

Question 33

What happens when you don't wait for air brakes to pressure up?

Answer 33

It may not allow that parking brake to release or may not have enough pressure to apply that brakes

Question 34

What does code say about filling holding tanks?

Answer 34

Code states that you must fill till the lowest drain in unit is flooded over

Question 35

What must you check for if furnace is close to the cook top?

Answer 35

Must ensure that the cook top is properly boxed in

Question 36

What are the two sizes of router bits

Answer 36

1/4" 1/2"