SPDI II Flashcards

(113 cards)

1
Q

Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe

A

Correct answer: ASTM D1785

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

An alarming device that produces a buzzing sound which is caused by the rapid vibration of armature.

A

Correct answer: Buzzer
Source: DepEd Information Sheet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

an alarm that produces an audible alarm tone when electrical energy is applied

A

Bell

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

applies current to an electromagnet pulled the bell’s clapper against the bell or gong and gave one chime

A

Single-Stroke Bells

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

a device that makes a loud prolonged sound as a signal or warning

A

Siren

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

It injects large quantities of fresh air into this compartment to mix the compartment’s entire contents and to provide oxygen for the aerobic digester process.

A

Correct answer: Aerator
Source: Audel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

The part of the valve housing through which the stem extends.

A

Correct answer: Bonnet
Source: ASPE

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is the standard specification for seamless copper water tube?

A

Correct answer: ASTM B88

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts

A

ASTM B888

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Standard Specification for High-Test Gray-Iron Castings

A

ASTM A88

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Which type of fire line installation has become obsolete and seldom installed?

A

Correct answer: Dry Standpipe
Source: How to Design and Install Plumbing by A.J. Matthias, Jr.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

the fire department can attach its pumping equipment

A

Wet Standpipe with Siamese Connection

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Water is immediately available, therefore the installation is a very practical one.

A

Wet Standpipe

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Pipe material used for LPG

A

Correct answer: PE
Source: NFPA 58

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

How do you connect PPR?

A

Correct answer: fusion welding
Source: pprsupply.com; ppr.almatherm; various websites

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

slip over the outside of two pipes to connect them, usually permanently

A

coupling

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

How do you connect pvc, cpvc, abs

A

solvent welding

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

How do you connect PEX

A

crimping

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Diameter of Class I System hose

A

Correct answer: 64 mm
Source: RA 9514

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Diameter of Class II hose

A
  • 38 mm
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

Consists of bacteria, algae, fungi, silt, protoza, and other colloidal matters making the water colored and acidic

A

Correct answer: suspended and colloidal materials
Source: PDE by Max Fajardo

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Consists of carbon dioxide, hydrogen sulfide, methance, oxygen, and nitroneous and organic compounds

A

Entrained gases

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Consists of calcium, magnesium sodium, iron and manganese

A

Dissolved Minerals

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

Consists of entrainment of radioactive substances from mining or processing ores

A

Radioactive materials

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
An approved pressure reduction device shall be permanently installed where static pressure of a wet standpipe exceeds _____. A.12 bar B. 7.2 bar C. 6.9 bar D .9.8 bar
Correct answer: 6.9 bar Source: RA 9514 Additional info: - 1 kg/cm^2- 0.98 bar - 1 psi- 0.069 bar
26
The pipe connection in which a ball is held in a cup-like that allows movement in every direction.
Correct answer: Ball Joint Source: RNPCP, Chapter 2
27
What Fire Extinguisher is least compatible for Class B Fires?
Correct answer: Wet Chemical
28
Can be used for Class A and B
Foam
29
May be used for Class A, B, C, and D
Dry Powder
30
May be used for Class B and Electrical
Carbon Dioxide
31
Fire extinguisher used for Class D fires
Correct answer: Dry Powder Extinguisher (also for Class A, B, and C) Source: umb.edu
32
for Class A fires
Water Extinguisher
33
for Class A and B
Foam Extinguisher
34
Wet Chemical
for Class A and F
35
A fitting that is used to close an open fitting
Correct answer: plug Source: Audel
36
used to close an open pipe
cap
37
used to close an open fitting
plug
38
used to reduce the size of an opening
bushing
39
provide convenient connections that can be easily unmade
unions
40
Diameter of dry standpipe if the highest outlet is 23 m or less
Correct answer: 102 mm Source: RA 9514
41
diameter of dry standpipe if the highest outlet is higher than 23 m
153 mm
42
The device that operates automatically when refilling the water tank after each discharge and shutting off completely when the tank is already full.
Correct answer: Float Valve Source: freedrinkingwater.com
43
a form of check valve, installed at the bottom of Pump suction line, inside the wet well.
Foot Valve
44
a valve that controls the pressure of a fluid or gas to a desired value, using negative feedback from the controlled pressure.
Pressure Regulating Valve
45
also called a one-way valve, is a device that allows the flow of fluids to move only in one direction
Check Valve
46
It spatters or scatters the effluent in drops or small blobs wherein they are mixed with the air
Correct answer: aerator Source: PDE by Max Fajard
47
designed to overcome tendency of the falling waste to stock up excessive back pressure at the bottom of the stack
Deaerator
48
Minimum diameter of combination standpipe
Correct answer: 150 mm Source: RA 9514
49
If the bell has hammer, the buzzer has _____.
Correct answer: Metal strip Source: DepEd Information Sheet
50
a thin sheet of electromagnetic materials which vibrates when electromagnet is energized and produces a buzzing sound.
Metal Strip
51
part of an electric bell; This is a small ball attached to the armature which strikes the gong.
Hammer or beater (striker)
52
part of an electric bell; A concave disc that produces loud sound when stuck by the hammer.
Gong bell
53
A liquid drain cleaner has a pH Level categorized as _____.
Correct answer: Basic
54
Which is typically not found on a pump curve? A. net positive suction head B. flow rate C. pipe diameter D. efficiency contour
Correct answer: C. pipe diameter Additional info: - another info that can be found on a pump curve is the impeller size
55
All dry standpipes shall be equipped with a two-way 63 mm outlet above the roof. All outlets shall be equipped with _____.
Correct answer: gate valves Source: NBC; PD 1096
56
A small pump connected to a fire sprinkler system to maintain pressure in the sprinkler pipes
Correct answer: Jockey pump Source: ASPE Volume 1
57
used for increasing pressure in of a water source when that source is not adequate for the system (fire sprinkler system)
fire pump
58
The minimum diameter of a dry standpipe requiring a 3-way Siamese connection
Correct answer: 125 mm Source: National Building Code
59
2-way siamese connection
100 mm dry standpipe
60
4-way siamese connection
150 mm dry standpipe
61
In an ordinary hazard, the coverage of 1 sprinkler head is _____.
Correct answer: 12 sqm Source: NFPA Chapter 13
62
Vents suitable for listed draft-hood equipped, gas-fired appliances, including most domestic heating and hot water systems
Correct answer: Type B vents Source: nachi.org
63
for venting listed gas-fired vented wall furnaces or gas-fired vented recessed heaters
Type BW
64
Use Type BH gas vents only for positive or negative pressure venting gas appliances producing flue gasses at Class I (up to 245 °C) or Class II (up to 135 °C) temperatures
Type BH
65
designed for venting approved oil-fired and natural-gas appliances that produce draft hood flue gasses that do not exceed a temperature of 570º F (299º C), or 926º F (299º C) for 10 minutes in an over-fire situation
Type L
66
The design, construction, and operation of the deep wells for the abstraction of groundwater shall be subject to the provisions of _____.
Correct answer: Water Code of the Philippines Source: NBC; PD 1096
67
A type of Globe valve which has a wide bearing surface producing good resistance to the cutting effects of scale, dirt, and other kinds of foreign matter found inside the pipe
Correct answer: Plug Source: ASPE
68
has a pressure-tight bearing between the disc and the seat recommended for cold water and any temperature service
Conventional Disc
69
does not fit into the seat opening, but over it, much as a bottlecap fits over the bottle opening
Composition Disc
70
a single tapered disc, thin at the bottom and thicker at the top
Solid Wedge
71
All interior wet standpipes shall be connected to a street main not less than ___ in diameter.
Correct answer: 4" or 100 mm Source: NBC; PD 1096
72
When installing _____, the authority having jurisdiction shall require evidence of the competency of the installers.
Correct answer: medical gas piping Source: UPC
73
The height of the tub should be between _____ from finished floor level.
Correct answer: 0.45 m - 0.50 m Source: UN Standards
74
Fire service connection in street front for Dry Standpipe shall be _____.
Correct answer: 46 to 122 cm Source: RA 9514 Additional info: - Mounting height is similar for combination standpipe
75
Which of the following is not a quarter-turn valve?
Correct answer: Needle Valves (similar to globe valves; for finer control of flow on smaller lines) Source: assuredautomation.com
76
The minimum size of a fire hose outlet of an interior wet standpipe.
Correct answer: 1 1/2" or 38 mm Source: RA 9514
77
The minimum size of a fire house outlet of dry standpipe
2 1/2" or 63.5 mm
78
All fire service connections shall be located on a street front not less than ______.
Correct answer: 46 cm Source: RA 9514
79
A nipple installed where fittings or valves are to be very close to each other
Correct answer: Close Nipple Source: Audel
80
A nipple installed where a large amount of unthreaded portion exists between the threads
Long Nipple
81
A nipple installed where a a small amount of unthreaded portion exists between the threads
Short/Shoulder Nipple
82
Standard for Installation of Sprinkler Systems
Correct answer: NFPA 13 Source: NFPA
83
Standard for Portable Fire Extinguishers
NFPA 10
84
Standard for the Installation of Standpipe and Hose Systems
NFPA 14
85
National Fire Alarm and Signaling Code
NFPA 72
86
A Positive Displacement Pump wherein the high-pressure seal reciprocates with the piston
Correct answer: Piston Pump Source: pumpsolutions.com.au
87
have a stationary, high-pressure seal that is attached to the cylinder housing of the pump
Plunger Pump
88
a simple kind of rotary pump that a pair of gears push the liquid
Gear Pump
89
Two screws turning against each other for pumping the liquid.
Screw Pump
90
A pipe installed in buildings not as part of the water supply or disposal system, but primarily for use as water conveyance in case of fire
Correct answer: Standpipe Source: PDE by Max Fajardo
91
always located near the stairs for use by firemen in case of fire.
Fire Hose
92
An integrated network of hydraulically designed piping system installed in a building, structure or area with outlets arranged in a systematic pattern which automatically discharges water when activated by heat or combustion products from a fire.
Sprinkler
93
Discharge pipes from pressure tanks shall extend _____ from and into the bottom of such tanks.
Correct answer: 5 cm Source: RA 9514
94
A Flow Meter that measures an induced voltage generated by the fluid as it flows through a pipe.
Correct answer: Electromagnetic Flow Meter Source: emerson.com
95
Most common water meters for residential and small commercial properties.
Positive Displacement
96
Determines the flow through a meter of known internal capacity. The speed of the flow can then be converted into a volume of flow to determine the usage.
Velocity Meter
97
sends the liquid through a rotor causing it to rotate at an angular velocity proportional to the fluid flow rate.
Turbine Flow Meter
98
The sum of static head and velocity head at a pump discharge
Correct answer: Total Discharge Head Source: ASPE
99
Total head at the pump discharge minus suction head or plus suction lift.
Total Head
100
The energy of a fluid at any particular point of a flow stream per weight of the fluid. Units of measurement are generally in feet (meters).
Head
101
Static head near the inlet of a pump relative to the pump centerline.
Suction Head
102
Maximum height of water closet according to BP 344
Correct answer: 0.45 m Source: BP 344
103
Maximum height of urinal lip according to BP 344
0.48 m
104
common water closet height
0.38 m
105
height of water closet for juvenile
0.33 m
106
This new concept in plumbing has almost completely eliminated the vent stack and other forms of ventilation, but still attained the desired functions and effectiveness.
Correct answer: Sovent System Source: PDE by Max Fajardo
107
a term used to describe soil or waste system where all pipings are of threaded pipe, tubing or other such rigid construction using recessed drainage fittings to correspond to the types of piping
Durham System
108
A pump has a 900 revolutions per minute. After the maintenance, the rate of revolution increased to 950. Calculate the new head pressure if the original head pressure is 100 ft.
Correct answer: 112 ft Head pressure increases as RPM increases.
109
Standard for the Fire Protection of Telecommunications Facilities
Correct answer: NFPA 76
110
Liquefied Petroleum Gas Code
NFPA 58
111
National Fire Alarm and Signaling Code
NFPA 72
112
Health Care Facilities Code
NFPA 99
113
A full-way valve used to regulate a fluid flow in which a threaded stem raises & lowers a wedge-shaped disk
Correct answer: Gate Valve Source: sciencedirect.com; various websites