301 Question Bank 2

Question 1

What is the 3M manual?

Answer 1

OPNAVINST 4790.4D

Question 2

What is the meaning of SPMIG

Answer 2

Standard PMS Materials Identification Guide

Question 3

What publication should be used by work center personnel to cross-reference the proper tools and materials for PMS

Answer 3

SPMIG

Question 4

The SPIN used in conjunction with the _______ to validate tools, parts, and materials

Answer 4

SPMIG

Question 5

What is a SDS?

Answer 5

Safety Data Sheet

Question 6

Who is your D3MA

Answer 6

FCC Ortega

Question 7

Who is overall responsible for the 3M program?

Answer 7

CO

Question 8

What is listed in the LOEP

Answer 8

All applicable maintenance for that work center

Question 9

What does MRC stand for?

Answer 9

Maintenance Requirement Card

Question 10

To replace missing/mutilated MRC and LGL, what tab in SKED is provided solely for printing specific MRC’s

Answer 10

PMS Documents

Question 11

How do you validate an MRC

Answer 11

MRC > MIP > LOEP > Change Page

Question 12

B4 4FCD Y indicates what?

Answer 12

MRC SYSCOM Contorl Number

Question 13

What does the ‘Y’ or ‘N’ in the MRC SYSCOM Contorl Number?

Answer 13

parts required or not required

Question 14

The rate block of an MRC is the receommned skill level needed to complete those maintenance requirements

Answer 14

True

Question 15

Which block of the MRC, detailing a listing of those precautions and references, directs attention to hazards to personnel while doing maintenance

Answer 15

Safety Precaution

Question 16

What block details the sequence of steps to be followed in peforming the maintenance action?

Answer 16

Procedure

Question 17

What is “Gun Decking”

Answer 17

Intentional falsification of records

Question 18

What does it mean if the SYSCOM Contorl Number at the bottom right of th eMRC is shown with brackets ‘[ ]’ around it?

Answer 18

MRC was printed from the PMS Viewer tab and should not be used due to potential loss of custom line-outs

Question 19

Common safety charpters when conducting maintenance: B5

Answer 19

Sign conservation

Question 20

Common safety charpters when conducting maintenance: B11

Answer 20

Tag-out

Question 21

What is ORM

Answer 21

Operational Risk Management

Question 22

Which safety precaution applies to death or injury

Answer 22

Warning

Question 23

Which statment applies to damage to equipment, if not correctly followed?

Answer 23

caution

Question 24

What is the purpose of the tag-out program

Answer 24

• provide perosnnel and ship safety and prevent damage to equipment
• prevent improper operation of an equipment
  provide special procedure prior to operating an equipment

Question 25

What type of tags prohibits the operation or removal of equipment that could jeopardize safety of personnel or endanger equipment?

Answer 25

Danger tags

Question 26

What type of tag would be used as a precautionary measure to provide temporary special instruction or to indicate that unusual action must be exercised to operate equipment?

Answer 26

Caution

Question 27

Can you operate a valve that has red tag on it that says the position is 'Shut'?

Answer 27

No

Question 28

What program is used to conduct tag-outs and tag-out audits?

Answer 28

eTAGOUT

Question 29

What is the purpose of the Instrument Log?

Answer 29

- The control doucment for administering labels. - Provides sequential listing of all OOC and Cal instruments

Question 30

How often are tag out audits normally performed

Answer 30

- Every two weeks, conducted by Department Head

Question 31

What symbol indicates a lost check

Answer 31

Circle

Question 32

Which symbol following a peridoicity code indicates that the procedure is intended to be scheduled and performed by Off-Ship Maintenance Personnel?

Answer 32

+

Question 33

What periodicity is Q-1

Answer 33

Quarterly

Question 34

What is an IEM?

Answer 34

Inactive Equipment Maintenance

Question 35

A piece of equipment that will not be operated for a least how many days may be placed in IEM

Answer 35

7 days

Question 36

What are the four checks related to an equipment in IEM

Answer 36

LU, PM, OT, SU

Question 37

What does the MY TASKS/TASKS display provide?

Answer 37

-provides a quick way for the MP to view MRCs, spotchecks, and/or SMA checks assigned to them -quick way to immediatly sign for completion of those tasks

Question 38

What is OMMS-NG used for?

Answer 38

used for corrective maintenance

Question 39

What is a JSN

Answer 39

Job Sequence Number; 4-digit number assigned by the work center to the maintenance action