Trim Carpentry Flashcards

(38 cards)

1
Q

Doors to be plum with jamb and level with header _________ of an inch on 6’8” doors, and ________ of an inch on 8’ doors.

A

1/8”

3/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Maintain a minimum _________ of an inch reveal around the perimeter of all doors, +/- __________ on the hinge side.

A

1/8”

1/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Doors to close and latch with __________ play on interior doors, and _________ of an inch on exterior doors.

A

No

1/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Doors not to ____________ when opened at a 45 degree angle.

A

Open (ghost)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

What’s the tolerance on chips, damage, defects or scratches on doors/base/case?

A

No tolerance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Thresholds to be tight to the jamb legs, gaps not to exceed ________ of an inch at ends (replace).

A

1/16”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Exterior doors with less than a _________ foot overhang to have a sill pan flashing system.

A

6’

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What’s the tolerance for binding, rubbing, or dragging on bi-pas closet doors?

A

No tolerance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Header casing at bi-pass doors to be level and secure with no ________.

A

Shiners

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Bi-pass closet doors to close flush on one side of the door opening with bowed framing allowed up to _________ of an inch.

A

1/8”

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

_____________ ____________ to be installed at all bi-pass closet doors.

A

Floor guides

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Finger pulls at bi-pass closet doors to be secured in place with __________, _________, or __________.

A

Nails
Adhesive
Caulk

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

____________ ___________ to be mounted on the back side of all bi-pass doors.

A

Door stoppers

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What’s the tolerance on base/case installed plumb, level and tight (no butt joints)?

A

No tolerance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

At what distance do you view base?

A

5’

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

At what distance do we view casing?

17
Q

Bows in base no to exceed _______ of an inch in _______ feet.

18
Q

Shelving material to be tight to the walls with gaps not to exceed __________ of an inch (replace).

19
Q

Bulkheads are to be installed ____________, ___________ and square to the wall.

A

Plumb
Level
Square

20
Q

Shelving to be installed level within __________ of an inch in _______ feet.

21
Q

Shelving _______ feet or less does not require a support bracket.

22
Q

Shelving under _________ feet requires one support bracket installed in a stud.

23
Q

Shelving over ________ feet requires 2 support brackets installed in a stud.

24
Q

Closet poles to be level, parallel to shelving, cut tight between side cleats within _______ of an inch.

25
Bullnose and/or exposed edges are to be ___________ __________.
Sanded smooth
26
What’s the tolerance for chips, gouges, nicks, scratches and saw marks on shelving?
No tolerance
27
Deadbolt holes are to be drilled through the jamb into the __________.
Framing
28
What is the proper depth that a deadbolt should be drilled?
When the deadbolt fully extends into the locked position
29
Deadbolt strike plates to be installed flush using _______ inch screws at all holes in the plate.
3”
30
Minimum of _________ 3” screws at the top hinge of all exterior doors.
2
31
There should be no ___________ around the weatherstrip on exterior doors.
Daylight
32
Fire door to have __________ _________ hinges and close/latch when held at a ________ degree angle.
Self closing | 45
33
Strike plates to be properly ___________ and installed flush.
Mortised
34
All screws to be ____________ and installed straight.
Countersunk
35
Maintain _____________ of an inch gap between flooring and bottom of doors.
1 3/8” - 1 1/2”
36
_________ _________ to be used at all interior and exterior doors.
Spring stops
37
________ _________ to be installed at all exterior portal doors.
Wall stopper
38
What’s the tolerance for damage, defects, dents, tarnish, scratches on door hardware?
No tolerance