Engines And Related Systems Flashcards

1
Q

Spell out the below engine system abbreviations:
FADEC, ECU, HMA, RDPS, PRI, REV, CONT, NG, NP, PTIT, AGB

A

Full Authority Digital Electronic Control
Electronic Control Unit
Hydromechanical Metering Assembly
Ratio Detector Power Supply
Primary
Reversionary
Contingency
Gas Producer
Power Turbine
Power Turbine Inlet Temperature
Accessory Gear Box

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Identify the 4 major sections of the T55-GA-714A Turbine Engine?

A

Intake, Compressor, Combustion, Exhuast

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Identify the three engine mounted components that have impending bypass indicators that should be checked on pre-flight inspection.

A

Main Fuel Filter, In-Line Fuel Filter, Main Oil Filter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

What NG speed constitutes an NG over speed?

A

Above 111%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Identify the engines torque limits (dual/single)?

A

Dual 100%, Single 123%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Identify at what PTIT time limited operations begin.

A

Above 816°C

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Identify the component that supplies the engine oil pressure signal that is seen on the Powertrain portion of the engine instrument page.

A

Oil Pressure Transmitter

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Identify the engine oil temperature limit.

A

149

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Identify what NR percent position we normally have the NR selector switch set at?

A

100%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What does the load share switch on the FADEC control panel allow the pilot to choose for engine load share?

A

Torque or PTIT

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

In relation to FADEC system what component is installed in the flight control closet for the purpose of sending thrust position and rate information to the ECU’s to eliminate rotor droop?

A

Thrust CPT(Control Position Transducer)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Identify the 5 stations of the engine system.

A

Intake, Compressor, Diffuser, Combustor, Exhaust

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What position should the ECL’s be in to see current fault BIT codes on the ECU’s?

A

Ground

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

An Engine FAULT detected by the ECU that does not impact the normal control of the engine is a ____ fault.

A

Soft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

An engine FAULT that could cause unacceptable engine or aircraft performance is a ____ fault.

A

Hard

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

When the Ignition Lock Switch is IN and ON this supplies power to the circuit of what two components on the engine for the purpose of engine starting?

A

Engine Ignition Exciter, Start Fuel Solenoid Valve

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

Below 6000 ft PA what component draws fuel out of the main tank to the engines in the event the main tank boost pump fails?

A

Engine Driven Fuel Pump

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

Identify the FADEC modes of operation the Bleed Band system automatically operates.

A

Primary and Reversionary

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Name the component on the engine that supplies the PTIT data to CAAS for display on the EICAS page on the MFD

A

PTIT Buss Bar

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Name the component that supplies the NR rotor speed data to CAAS for display on the EICAS page on the MFD.

A

Permanent Magnetic Generators in the Main Generators

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

Name the component that supplies the NG speed data to CAAS for display on the EICAS page on the MFD and where is it mounted?

A

NG speed pickup assembly mounted on the Engine Oil Pump

22
Q

Name the component mounted on the engine that supplies the engine torque data to CAAS for display on the EICAS page on the MFD?

A

Torque Junction Box

23
Q

Name the component on the engine that supplies the NP speed data to CAAS on the EICAS page on the MFD.

A

NP Speed Assembly

24
Q

Name the component that eliminates small particle build up on the engine chip detector to prevent an engine chip caution.

A

Engine CHIP Fuzz Burn-off Module

25
Q

During a preflight inspection you are checking engine fluid lines for what two faults?

A

Leaks and Chaffing

26
Q

Write out the underlined Immediate Action Steps for Single Engine Failure (ENG1 FAIL or ENG2 FAIL WARNING)

A

External Load- Jettison (as required)
FLT DIR CPLR- Uncouple
DAFCS modes- OFF

27
Q

Engine fire extinguisher bottle gauges should be checked on preflight in accordance with what chart in the TM 1-1520-271-CL?

A

Engine Fire Extinguisher Bottle Pressure Chart

28
Q

Name the system that automatically controls engine operation throughout the full operating range of the engine.

A

FADEC

29
Q

ENG FAIL WARNINGS will be displayed on which MFDs when active?

A

All 5 MFDs

30
Q

The FADEC Control Panel located on the overhead switch panel provides what to the aircraft operators?

A

Engine Control

31
Q

With the ENG COND levers in FLT and PRI mode selected NR will be maintained at what selected speed?

A

NR Switch Selection (typically 100%)

32
Q

2 places a chip caution will appear

A

MFD, Maintenance Panel

33
Q

The main fuel filter removes contaminants from fuel prior to reach what power plant component?

A

HMA

34
Q

After starting the first engine, the second engine must be started or motored for __________ within _________ .

A

10 seconds

3 minutes

35
Q

What are the two functions of the liquid to liquid cooler?

A

Dissipates heat from engine oil

Warms fuel prior to ignition

(Thermal Transference)

36
Q

Name the component mounted on the AGB that supplies the engine CHIP caution signal

A

Chip Detector Magnet

37
Q

Where is the Chip Detector Magnet located?
(Mounted on what power plant component?)

A

AGB

38
Q

What are the two sections of the HMA?

A

HMU and FPU

Hydromechanical Unit and Fuel Pump Unit

39
Q

What are the five features of the HMA?

A

-Bleed Air Port
-Main Metering Valve
-3 Phase Alternator
-NG Speed Sensor
-Reversionary Stepper Motor

40
Q

The engine interstate air bleed aids compressor stall by ______.
It is operated by the FADEC system’s _________.

A

Pneumatically tightening or loosening a metal band around vent holes in the compressor section.

It is operated by the FADEC systems’s HMA (hydro mechanical metering assembly)

41
Q

What is the main source of power for FADEC systems?

A

The integral alternator located in the HMA, above 48% NG

42
Q

Is fuel pressure measured after the main boost pumps or after the engine driven fuel pumps?

A

Fuel pressure is measured after the boost pumps

43
Q

What Engines are on the CH47

A

Lycoming T55-GA-714A

44
Q

How much shaft horsepower per engine

A

5,049

45
Q

Identify the 5 Engine Stations

A

Intake station
Compressor Station
Diffuser Station
Combustor Station
Exhaust Station

46
Q

What does the Torquemeter System consist of

A

Internal torque components
Torquemeter Junction Box
Radio Detection Power Supply (RDPS)

47
Q

What percent does FADEC load share keep NR within?
What degree range does FADEC load share keep PTIT within

A

2% TQ
30° PTIT

48
Q

What does CPT stand for, and what does the Thrust CPT do

A

Control Position Transducer
Transmits position and rate of movement to thrust ILCA And to FADEC. So that fuel needs can be telegraphed and more rapidly met.

49
Q

HMA spelled out

A

Hydromechanical Metering Assembly

50
Q

RDPS

A

Radio Detector Power Supply

51
Q

ECU

A

Electronic Control Unit

52
Q

AGB

A

Accessory Gear Box